EN 420:2003
(Main)Protective gloves - General requirements and test methods
Protective gloves - General requirements and test methods
This standard defines the general requirements and relevant test procedures for glove design and construction, resistance of glove materials to water penetration, innocuousness, comfort and efficiency, marking and information supplied by the manufacturer applicable to all protective gloves.
NOTE It can also be applicable to arm protectors and gloves permanently incorporated in containment enclosures.
This European Standard does not address the protective properties of gloves and therefore should not be used alone but only in combination with the appropriate specific European Standard(s).
A non exhaustive list of these standards is given in the Bibliography.
Schutzhandschuhe - Allgemeine Anforderungen und Prüfverfahren
Diese Norm legt die für alle Schutzhandschuhe anzuwendenden relevanten Prüfverfahren und die allgemeinen Anforderungen zu Gestaltungsgrundsätzen, Handschuhkonfektionierung, Widerstand des Handschuhmaterials gegen Wasserdurchdringung, Unschädlichkeit, Komfort und Leistungsvermögen sowie die vom Hersteller vorzu-nehmende Kennzeichnung und vom Hersteller zu liefernden Informationen fest.
ANMERKUNG Sie kann auch auf Armschutz und auf Handschuhe angewendet werden, die ständig in geschlossenen Behältnissen eingesetzt werden.
Diese Europäische Norm befasst sich nicht mit den schützenden Eigenschaften von Handschuhen und ist daher nie alleine, sondern nur in Kombination mit den zutreffenden spezifischen Europäischen Normen anzuwenden.
Eine nicht abschließende Liste dieser Normen enthalten die Literaturhinweise dieser Norm.
Gants de protection - Exigences générales et méthodes d'essai
La présente Norme européenne définit les exigences générales et les procédures d'essai concernant l'ergonomie et la construction du gant, la résistance des matériaux constitutifs à la pénétration de l'eau, l'innocuité, le confort et l'efficacité, le marquage et l'information fournie par le fabricant applicables à tous les gants de protection.
NOTE Elle peut aussi s'appliquer aux protecteurs du bras et aux gants incorporés de manière permanente à des enceintes fermées.
Cette présente Norme européenne ne concerne pas les propriétés de protection des gants et ne doit donc pas être utilisée seule mais seulement en association avec le(s) Norme(s) européenne(s) spécifique(s) appropriée(s).
Une liste non exhaustive de ces normes est donnée dans la bibliographie.
Varovalne rokavice - Splošne zahteve in preskusne metode
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Protective gloves - General requirements and test methodsVarovalne rokavice - Splošne zahteve in preskusne metodeGants de protection - Exigences générales et méthodes d'essaiSchutzhandschuhe - Allgemeine Anforderungen und Prüfverfahren13.340.40Varovanje dlani in rokHand and arm protectionICS:SIST EN 420:2003enTa slovenski standard je istoveten z:EN 420:200301-december-2003SIST EN 420:2003SLOVENSKI
STANDARDSIST EN 420:19961DGRPHãþD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 420September 2003ICS 13.340.40Supersedes EN 420:1994English versionProtective gloves - General requirements and test methodsGants de protection - Exigences générales et méthodesd'essaiSchutzhandschuhe - Allgemeine Anforderungen undPrüfverfahrenThis European Standard was approved by CEN on 24 July 2003.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and UnitedKingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2003 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 420:2003 E
Definition of "For minimal risks only".20Annex B (normative)
Leather - Chemical tests - Determination of chromium VI content.21B.1Scope.21B.2Principle.21B.3Definition.21B.4Chemicals.21B.5Apparatus.22B.6Procedure.23B.7Calculation and expression of results.25B.8Accuracy.26B.9Test report.26B.10Reversed phase material.26Annex C (normative)
Pictograms.27Annex D (informative)
Test results — Uncertainty of measurement.28Annex ZA (informative)
Clauses of this European Standard addressing essential requirements orother provisions of EU Directives.29Bibliography.30
Handb
Backc
PalmFigure 1 — Definitions of hand, palm and back3.1handpart of the body from the tip of the middle finger to the wrist3.2glovepersonal protective equipment (PPE) which protects the hand or part of the hand against hazards. It canadditionally cover part of the forearm and arm3.3glove palmpart of the glove which covers the palm of the hand, i.e. from the wrist to the base of the fingers3.4glove backpart of the glove which covers the back of the hand (i.e. from the wrist to the base of the fingers)
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.