EN 1337-2:2000
(Main)Structural bearings - Part 2: Sliding elements
Structural bearings - Part 2: Sliding elements
This European Standard specifies the characteristics for the design and manufacture of sliding elements and guides which are not structural bearings but only parts of them for combination with structural bearings as defined in other Parts of this European Standard.
Suitable combinations are shown in Table 1 of EN 1337-1:2000. Sliding surfaces with a diameter of the circumscribing circle of single or multiple PTFE sheets less than 75 mm or greater than 1500 mm, or with effective bearing temperatures less than ¿35°C or greater than 48°C are outside the scope of this European Standard. Sliding elements for use as temporary devices during construction, for example during launching of the superstructure, are also outside the scope of this European Standard. In this standard the specification is also given for curved sliding surfaces which are not part of separate sliding elements but which are incorporated in cylindrical or spherical PTFE bearings as per prEN 1337-7:1996. NOTE The general principles detailed in this European Standard may be applied for sliding elements outside this scope, but their suitability for the intended use should be proven.
Lager im Bauwesen - Teil 2: Gleitteile
Diese Europäische Norm legt Angaben für Bemessung und Herstellung von Gleitteilen und Führungen fest, die keine Lager, sondern nur Teile von solchen sind, für die Kombination mit Lagern, die in anderen Teilen dieser Norm geregelt sind. Geeignete Kombinationen sind in EN 1337-1:2000, Tabelle 1 angegeben. Gleitflächen aus ein- oder mehrteiligen PTFE-Platten, deren umschreibender Kreis einen Durchmesser von weniger als 75 mm oder mehr als 1500 mm hat oder deren wirksame Lagertemperatur niedriger als -35 °C oder
höher als 48 °C ist, liegen außerhalb des Anwendungsbereichs dieser Norm. Gleitelemente, die vorübergehend als Hilfslager während der Bauphase dienen (z. B. beim Taktschieben des Überbaus) liegen außerhalb des Anwendungsbereichs dieser Norm. In dieser Norm sind auch Angaben für gekrümmte Gleitflächen enthalten, die nicht Teile von separaten Gleitteilen sind, sondern die in Kalotten- und Zylinderlagern nach prEN 1337-7:1996 eingebaut werden. ANMERKUNG Die in dieser Europäischen Norm beschriebenen Grundsätze dürfen für Gleitelemente angewendet werden, die außerhalb dieses Anwendungsbereiches liegen, jedoch ist deren Brauchbarkeit für
den vorgeschriebenen Verwendungszweck nachzuweisen.
Appareils d'appui structuraux - Partie 2: Eléments de glissement
La présente Norme européenne spécifie les caractéristiques relatives à la conception et à la fabrication des éléments de glissement et des guides qui ne sont pas des appareils d'appui structuraux mais seulement des pièces qui y sont associées sous différentes combinaisons, telles que définies dans les autres parties de la présente Norme européenne. Les combinaisons appropriées sont indiquées au Tableau 1 de l'EN 1337-1:2000. Les surfaces de glissement ayant un diamètre du cercle de circonscription des feuilles uniques ou multiples de PTFE inférieur à 75 mm ou supérieur à 1 500 mm ou des températures effectives d'appareils d'appui inférieures à - 35 °C ou supérieures à + 48 °C n'entrent pas dans le domaine d'application de la présente Norme européenne. Les éléments de glissement utilisés temporairement pendant la construction (comme lors du lancement de la structure) n'entrent pas dans le domaine d'application de la présente Norme européenne. La présente Norme européenne donne également la spécification relative aux surfaces courbes de glissement qui ne font pas partie d'éléments de glissement séparés, mais qui sont intégrées dans des appareils d'appui cylindriques et sphériques comportant du PTFE décrits dans le prEN 1337-7 :1996. NOTE Les principes généraux décrits en détail dans la présente Norme européenne peuvent être appliqués aux éléments de glissement qui n'entrent pas dans ce domaine d'application, mais il convient d'attester qu'ils sont adaptés à l'usage prévu.
Konstrukcijska ležišča - 2. del: Drsni elementi
General Information
- Status
- Withdrawn
- Publication Date
- 12-Dec-2000
- Withdrawal Date
- 16-Mar-2004
- Technical Committee
- CEN/TC 167 - Structural bearings
- Drafting Committee
- CEN/TC 167/WG 3 - Sliding, spherical and cylindrical elements
- Current Stage
- 9960 - Withdrawal effective - Withdrawal
- Start Date
- 17-Mar-2004
- Completion Date
- 17-Mar-2004
- Directive
- 89/106/EEC - Construction products
Relations
- Effective Date
- 22-Dec-2008
- Referred By
EN 1998-2:2005 - Eurocode 8 - Design of structures for earthquake resistance - Part 2: Bridges - Effective Date
- 28-Jan-2026
Get Certified
Connect with accredited certification bodies for this standard
ICC Evaluation Service
Building products evaluation and certification.
QAI Laboratories
Building and construction product testing and certification.
Aboma Certification B.V.
Specialized in construction, metal, and transport sectors.
Sponsored listings
Frequently Asked Questions
EN 1337-2:2000 is a standard published by the European Committee for Standardization (CEN). Its full title is "Structural bearings - Part 2: Sliding elements". This standard covers: This European Standard specifies the characteristics for the design and manufacture of sliding elements and guides which are not structural bearings but only parts of them for combination with structural bearings as defined in other Parts of this European Standard. Suitable combinations are shown in Table 1 of EN 1337-1:2000. Sliding surfaces with a diameter of the circumscribing circle of single or multiple PTFE sheets less than 75 mm or greater than 1500 mm, or with effective bearing temperatures less than ¿35°C or greater than 48°C are outside the scope of this European Standard. Sliding elements for use as temporary devices during construction, for example during launching of the superstructure, are also outside the scope of this European Standard. In this standard the specification is also given for curved sliding surfaces which are not part of separate sliding elements but which are incorporated in cylindrical or spherical PTFE bearings as per prEN 1337-7:1996. NOTE The general principles detailed in this European Standard may be applied for sliding elements outside this scope, but their suitability for the intended use should be proven.
This European Standard specifies the characteristics for the design and manufacture of sliding elements and guides which are not structural bearings but only parts of them for combination with structural bearings as defined in other Parts of this European Standard. Suitable combinations are shown in Table 1 of EN 1337-1:2000. Sliding surfaces with a diameter of the circumscribing circle of single or multiple PTFE sheets less than 75 mm or greater than 1500 mm, or with effective bearing temperatures less than ¿35°C or greater than 48°C are outside the scope of this European Standard. Sliding elements for use as temporary devices during construction, for example during launching of the superstructure, are also outside the scope of this European Standard. In this standard the specification is also given for curved sliding surfaces which are not part of separate sliding elements but which are incorporated in cylindrical or spherical PTFE bearings as per prEN 1337-7:1996. NOTE The general principles detailed in this European Standard may be applied for sliding elements outside this scope, but their suitability for the intended use should be proven.
EN 1337-2:2000 is classified under the following ICS (International Classification for Standards) categories: 91.010.30 - Technical aspects. The ICS classification helps identify the subject area and facilitates finding related standards.
EN 1337-2:2000 has the following relationships with other standards: It is inter standard links to EN 1337-2:2004, EN 1998-2:2005. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
EN 1337-2:2000 is associated with the following European legislation: EU Directives/Regulations: 305/2011, 89/106/EEC; Standardization Mandates: M/104. When a standard is cited in the Official Journal of the European Union, products manufactured in conformity with it benefit from a presumption of conformity with the essential requirements of the corresponding EU directive or regulation.
EN 1337-2:2000 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Lager im Bauwesen - Teil 2: GleitteileAppareils d'appui structuraux - Partie 2: Eléments de glissementStructural bearings - Part 2: Sliding elements91.010.30Technical aspectsICS:Ta slovenski standard je istoveten z:EN 1337-2:2000SIST EN 1337-2:2001en01-april-2001SIST EN 1337-2:2001SLOVENSKI
STANDARD
SIST EN 13
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...