Plastics piping systems - Polyethylene (PE) pipes - Test method for the resistance to internal pressure after application of squeeze-off

This standard specifies a method for determining the resistance to internal pressure of polyethylene (PE) pipes after being subjected to a sqeeze-off procedure and then tested for hydrostatic strength.

Kunststoff-Rohrleitungssysteme - Rohre aus Polyethylen (PE) - Bestimmung der Widerstandsfähigkeit gegen Innendruck nach Abquetschen

Diese Norm legt ein Verfahren zur Bestimmung des widerstand gegen Innendruck vonRohren aus Polyethylen (PE) nach Reduzierung des Durchflußquerschnittes durch Abquetschen fest.

Systèmes de canalisations en plastique - Tubes en polyéthylène (PE) - Méthode d'essai de résistance à la pression interne après application de l'écrasement

La présente norme européenne spécifie une méthode de détermination de résistance à la pression interne des tubes polyéthylène (PE) après écrasement puis l'essai de résistance hydrostatique.

Cevni sistemi iz polimernih materialov - Cevi iz polietilena (PE) - Metoda za preskus odpornosti proti notranjemu tlaku po izvedenem stiskanju cevi (squeeze-off

General Information

Status
Withdrawn
Publication Date
19-Aug-1997
Withdrawal Date
20-Jan-2026
ICS
23.040.20 - Plastics pipes
Technical Committee
CEN/TC 155 - Plastics piping systems and ducting systems
Drafting Committee
CEN/TC 155/WG 33 - Thermoplastics piping systems for soil & waste discharge and non-pressure drainage and sewerage
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
07-May-2025
Completion Date
21-Jan-2026
Directive
305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
89/106/EEC - Construction products
Ref Project
SIST EN 12106:1999 - Plastics piping systems - Polyethylene (PE) pipes - Test method for the resistance to internal pressure after application of squeeze-off

Relations

Replaced By
EN 12106:2025 - Plastics piping systems - Polyethylene (PE), crosslinked polyethylene (PE-X) and unplasticized polyamide (PA-U) pipes - Test method for the resistance to internal pressure after application of squeeze-off
Effective Date
22-Nov-2023
Revised
prEN 12106 - Plastics piping systems - Polyethylene (PE) and crosslinked polyethylene (PE-X) pipes - Test method for the resistance to internal pressure after application of squeeze-of
Effective Date
06-Feb-2013

Frequently Asked Questions

EN 12106:1997 is a standard published by the European Committee for Standardization (CEN). Its full title is "Plastics piping systems - Polyethylene (PE) pipes - Test method for the resistance to internal pressure after application of squeeze-off". This standard covers: This standard specifies a method for determining the resistance to internal pressure of polyethylene (PE) pipes after being subjected to a sqeeze-off procedure and then tested for hydrostatic strength.

This standard specifies a method for determining the resistance to internal pressure of polyethylene (PE) pipes after being subjected to a sqeeze-off procedure and then tested for hydrostatic strength.

EN 12106:1997 is classified under the following ICS (International Classification for Standards) categories: 23.040.20 - Plastics pipes. The ICS classification helps identify the subject area and facilitates finding related standards.

EN 12106:1997 has the following relationships with other standards: It is inter standard links to EN 12106:2025, prEN 12106. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.

EN 12106:1997 is associated with the following European legislation: EU Directives/Regulations: 305/2011, 89/106/EEC. When a standard is cited in the Official Journal of the European Union, products manufactured in conformity with it benefit from a presumption of conformity with the essential requirements of the corresponding EU directive or regulation.

EN 12106:1997 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Cevni sistemi iz polimernih materialov - Cevi iz polietilena (PE) - Metoda za preskus odpornosti proti notranjemu tlaku po izvedenem stiskanju cevi (squeeze-offKunststoff-Rohrleitungssysteme - Rohre aus Polyethylen (PE) - Bestimmung der Widerstandsfähigkeit gegen Innendruck nach AbquetschenSystemes de canalisations en plastique - Tubes en polyéthylene (PE) - Méthode d'essai de résistance a la press
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

Loading comments...