EN ISO 11148-8:2011

SLOVENSKI STANDARD
01-februar-2012
1DGRPHãþD
SIST EN 792-8:2001+A1:2008
1HHOHNWULþQDURþQDRURGMD9DUQRVWQH]DKWHYHGHO%UXVLOQLNLLQSROLUQLNL,62

Hand-held non-electric power tools - Safety requirements - Part 8: Sanders and polishers
(ISO 11148-8:2011)
Handgehaltene nichtelektrisch betriebene Maschinen Sicherheitsanforderungen Teil 8:
Schleifmaschinen für Schleifblätter und Polierer (ISO 11148-8:2011)
Machines portatives à moteur non électrique - Exigences de sécurité - Partie 8:
Polisseuses-lustreuses et ponceuses (ISO 11148-8:2011)
Ta slovenski standard je istoveten z: EN ISO 11148-8:2011
ICS:
25.140.10 3QHYPDWLþQDRURGMD Pneumatic tools
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 11148-8
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2011
ICS 25.140.10 Supersedes EN 792-8:2001+A1:2008
English Version
Hand-held non-electric power tools - Safety requirements - Part
8: Sanders and polishers (ISO 11148-8:2011)
Machines portatives à moteur non électrique - Exigences Handgehaltene nicht elektrisch betriebene Maschinen -
de sécurité - Partie 8: Polisseuses-lustreuses et ponceuses Sicherheitsanforderungen - Teil 8: Schleifmaschinen für
(ISO 11148-8:2011) Schleifblätter und Polierer (ISO 11148-8:2011)
This European Standard was approved by CEN on 12 November 2011.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11148-8:2011: E
worldwide for CEN national Members.

Contents Page
Foreword .3
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 2006/42/EC .4

Foreword
This document (EN ISO 11148-8:2011) has been prepared by Technical Committee ISO/TC 118
"Compressors and pneumatic tools, machines and equipment" in collaboration with Technical Committee
CEN/TC 255 “Hand-held, non-electric power tools - Safety” the secretariat of which is held by SIS.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by June 2012, and conflicting national standards shall be withdrawn at
the latest by June 2012.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 792-8:2001+A1:2008.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive.
For relationship with EU Directive, see informative Annex ZA, which is an integral part of this document.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 11148-8:2011 has been approved by CEN as a EN ISO 11148-8:2011 without any
modification.
Annex ZA
(informative)
Relationship between this European Standard and the Essential
Requirements of EU Directive 2006/42/EC
This European Standard has been prepared under a mandate given to CEN by the European Commission
and the European Free Trade Association to provide a means of conforming to Essential Requirements of the
New Approach Directive 2006/42/EC on machinery.
Once this standard is cited in the Official Journal of the European Union under that Directive and has been
implemented as a national standard in at least one Member State, compliance with the clauses of this
standard confers, within the limits of the scope of this standard, a presumption of conformity with the
corresponding Essential Requirements of that Directive except ER 1.5.7 and associated EFTA regulations.
WARNING — Other requirements and other EU Directives may be applicable to the product(s) falling
within the scope of this standard.

INTERNATIONAL ISO
STANDARD 11148-8
First edition
2011-12-01
Hand-held non-electric power tools —
Safety requirements —
Part 8:
Sanders and polishers
Machines portatives à moteur non électrique — Exigences de
sécurité —
Partie 8: Polisseuses-lustreuses et ponceuses

Reference number
ISO 11148-8:2011(E)
©
ISO 2011
ISO 11148-8:2011(E)
©  ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56  CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2011 – All rights reserved

ISO 11148-8:2011(E)
Contents Page
Foreword . iv
Introduction . v
1  Scope . 1
2  Normative references . 2
3  Terms and definitions . 2
3.1  General terms and definitions . 2
3.2  Terms and definitions related to sanders and polishers . 4
4  Safety requirements and/or protective measures . 4
4.1  General . 4
4.2  Mechanical safety . 5
4.3  Thermal safety . 6
4.4  Noise reduction . 6
4.5  Vibration . 7
4.6  Materials and substances processed, used or exhausted . 7
4.7  Ergonomics . 7
4.8  Controls . 8
5  Verification . 9
5.1  General conditions for tests . 9
5.2  Noise . 9
5.3  Vibration . 9
5.4  Unintentional start . 9
5.5  Power tool construction . 9
5.6  Structure of verification . 9
6  Information for use . 10
6.1  Marking, signs and written warnings . 10
6.2  Instruction handbook . 11
6.3  Operating instructions . 16
6.4  Data . 16
6.5  Maintenance instructions . 17
Annex A (informative) List of significant hazards . 18
Annex B (informative) Examples of sanders and polishers covered by this part of ISO 11148 . 20
Annex C (normative) Symbols for labels and signs . 21
Annex D (informative) Examples of abrasive products for use with polishers and sanders . 22
Bibliography . 23

ISO 11148-8:2011(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 11148-8 was prepared by Technical Committee ISO/TC 118, Compressors and pneumatic tools,
machines and equipment, Subcommittee SC 3, Pneumatic tools and machines.
ISO 11148 consists of the following parts, under the general title Hand-held non-electric power tools — Safety
requirements:
 Part 1: Assembly power tools for non-threaded mechanical fasteners
 Part 2: Cutting-off and crimping power tools
 Part 3: Drills and tappers
 Part 4: Non-rotary percussive power tools
 Part 5: Rotary percussive drills
 Part 6: Assembly power tools for threaded fasteners
 Part 7: Grinders
 Part 8: Sanders and polishers
 Part 9: Die grinders
 Part 10: Compression power tools
 Part 11: Nibblers and shears
 Part 12: Circular, oscillating and reciprocating saws
A part
...