EN ISO 4623-2:2016

SLOVENSKI STANDARD
01-november-2016
1DGRPHãþD
SIST EN ISO 4623-2:2004
SIST EN ISO 4623-2:2004/AC:2006
Barve in laki - Ugotavljanje odpornosti proti filiformni koroziji - 2. del: Podlage iz
aluminija (ISO 4623-2:2016)
Paints and varnishes - Determination of resistance to filiform corrosion - Part 2:
Aluminium substrates (ISO 4623-2:2016)
Beschichtungsstoffe - Bestimmung der Beständigkeit gegen Filiformkorrosion - Teil 2:
Aluminium als Substrat (ISO 4623-2:2016)
Peintures et vernis - Détermination de la résistance à la corrosion filiforme - Partie 2:
Subjectiles en aluminium (ISO 4623-2:2016)
Ta slovenski standard je istoveten z: EN ISO 4623-2:2016
ICS:
87.040 Barve in laki Paints and varnishes
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 4623-2
EUROPEAN STANDARD
NORME EUROPÉENNE
August 2016
EUROPÄISCHE NORM
ICS 87.040 Supersedes EN ISO 4623-2:2004
English Version
Paints and varnishes - Determination of resistance to
filiform corrosion - Part 2: Aluminium substrates (ISO
4623-2:2016)
Peintures et vernis - Détermination de la résistance à la Beschichtungsstoffe - Bestimmung der Beständigkeit
corrosion filiforme - Partie 2: Subjectiles en aluminium gegen Filiformkorrosion - Teil 2: Aluminium als
(ISO 4623-2:2016) Substrat (ISO 4623-2:2016)
This European Standard was approved by CEN on 23 July 2016.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 4623-2:2016 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 4623-2:2016) has been prepared by Technical Committee ISO/TC 35 “Paints
and varnishes” in collaboration with Technical Committee CEN/TC 139 “Paints and varnishes” the
secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by February 2017, and conflicting national standards
shall be withdrawn at the latest by February 2017.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document supersedes EN ISO 4623-2:2004.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 4623-2:2016 has been approved by CEN as EN ISO 4623-2:2016 without any
modification.
INTERNATIONAL ISO
STANDARD 4623-2
Second edition
2016-08-15
Paints and varnishes — Determination
of resistance to filiform corrosion —
Part 2:
Aluminium substrates
Peintures et vernis — Détermination de la résistance à la corrosion
filiforme —
Partie 2: Subjectiles en aluminium
Reference number
ISO 4623-2:2016(E)
©
ISO 2016
ISO 4623-2:2016(E)
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved

ISO 4623-2:2016(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 2
5 Sampling . 2
6 Apparatus . 2
7 Reagents . 2
8 Test panels . 2
8.1 Material and dimensions . 2
8.2 Preparation and coating . . 3
8.3 Drying and conditioning . 3
8.4 Thickness of coating . 3
9 Procedure. 3
9.1 Determination . 3
9.2 Scribing the test panels . 3
9.3 Testing . 5
9.4 Inspection of test panels . 5
10 Evaluation of the degree of filiform corrosion . 5
11 Precision . 5
12 Test report . 5
Bibliography . 7
ISO 4623-2:2016(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment,
as well as information about ISO’s adherence to the World Trade Organization (WTO) principles in the
Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html.
The committee responsible for this document is ISO/TC 35, Paints and varnishes, Subcommittee SC 9,
General test methods for paints and varnishes.
This second edition cancels and replaces the first edition (ISO 4623-2:2003), which has been technically
revised. It also incorporates the Technical Corrigendum ISO 4623-2:2003/Cor 1:2005. The following
main changes have been made:
a) duplicate determination has been changed to triplicate determination;
b) information on the shape of the scribe marks has been added;
c) the width of the scribe marks has been changed to be in line with EN
...