EN 17109:2020+A1:2024

SLOVENSKI STANDARD
01-december-2024
Gorniška oprema - Individualni varnostni sistemi za vrvne plezalne parke -
Varnostne zahteve in preskusne metode
Mountaineering equipment - Individual safety systems for rope courses - Safety
requirements and test methods
Bergsteigerausrüstung - Einzelsicherungssysteme für Seilgärten -
Sicherheitsanforderungen und Prüfverfahren
Équipement d'alpinisme et d'escalade - Systèmes d'assurage individuels pour parcours
acrobatiques en hauteur - Exigences de sécurité et méthodes d'essai
Ta slovenski standard je istoveten z: EN 17109:2020+A1:2024
ICS:
97.220.40 Oprema za športe na Outdoor and water sports
prostem in vodne športe equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 17109:2020+A1
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2024
EUROPÄISCHE NORM
ICS 97.220.40 Supersedes EN 17109:2020
English Version
Mountaineering equipment - Individual safety systems for
rope courses - Safety requirements and test methods
Équipement d'alpinisme et d'escalade - Systèmes Bergsteigerausrüstung - Einzelsicherungssysteme für
d'assurage individuels pour parcours acrobatiques en Seilgärten - Sicherheitsanforderungen und
hauteur - Exigences de sécurité et méthodes d'essai Prüfverfahren
This European Standard was approved by CEN on 15 December 2019 and includes Amendment 1 approved by CEN on 12 August
2024.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 17109:2020+A1:2024 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Safety requirements . 6
4.1 Design and construction . 6
4.2 Manual extraction test for categories C, D and E . 8
4.3 Static strength . 8
4.3.1 Function under a test load (only for MCD with pulleys) . 8
4.3.2 Deformation test for MCD . 8
4.3.3 Static strength test for all ISS with all categories of MCD . 9
4.3.4 MCD transversal static strength test . 9
4.4 Locking devices of the opening of the MCD . 9
4.5 Stability of tape . 9
4.6 Corrosion resistance . 9
5 Test methods . 9
5.1 Design and construction . 9
5.2 Manual extraction test for categories C, D and E . 9
5.3 Static tests . 10
5.3.1 General. 10
5.3.2 Function under a test load (only for MCD with pulleys) . 11
5.3.3 !Deformation test for MCD of category E and A to D where relevant" . 11
5.3.4 Static strength test for all ISS or their component . 11
5.3.5 MCD transversal static test . 12
5.4 Stitching test . 13
5.5 Stability of tape . 13
5.5.1 Preparation . 13
5.5.2 Test . 14
5.6 Corrosion resistance test . 14
6 Marking . 14
7 !Manufacturer’s instructions and information" . 14
Annex A (normative) !Compatibility of categories D and E MCD with safety line
supports" . 16
Annex B (informative) Standards on mountaineering equipment . 17
Annex ZA (informative) !Relationship between this European Standard and the essential
requirements of Regulation (EU) 2016/425 aimed to be covered" . 19

European foreword
This document (EN 17109:2020+A1:2024) has been prepared by Technical Committee CEN/TC 136
“Sports, playground and other recreational facilities and equipment”, the secretariat of which is held by
DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2025, and conflicting national standards shall be
withdrawn at the latest by April 2025.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document includes Amendment 1 approved by CEN on 12 August 2024.
This document supersedes EN 17109:2020.
The start and finish of text introduced or altered by amendment is indicated in the text by tags !".
This document has been prepared under a standardisation request addressed to CEN and CENELEC by
the European Commission. The Standing Committee of the EFTA States subsequently approves these
requests for its Member States.
For the relationship with EU Legislation, see informative Annex ZA, which is an integral part of this
document.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
1 Scope
This document specifies safety requirements and test methods for components of an individual safety
system for protection against a fall from height used in permanent and mobile rope courses as defined
in !EN 15567-1:2015+A1:2020".
The products considered in this !document" are not intended to limit, by themselves, the
deceleration of the fall of the user, as defined in !EN 15567-1:2015+A1:2020". For this
requirement, it is essential to consider the whole ropes course system.
Safety lines and harnesses are not covered in this !document".
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
!EN 362:2004, Personal protective equipment against falls from a height — Connectors"
EN 565:2017, Mountaineering equipment — Tape — Safety requirements and test methods
EN 12275:2013, Mountaineering equipment — Connectors — Safety requirements and test methods
!EN 15567-1:2015+A1:2020", Sports and recreational facilities — Ropes courses — Part 1:
Construction and safety requirements
EN ISO 9227:2017, Corrosion tests in artificial atmospheres — Salt spray tests (ISO 9227:2017)
ISO 7000:2004, Graphical symbols for use on equipment — Registered
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
• IEC Electropedia: available at https://www.electropedia.org/
• ISO Online browsing platform: available at https://www.iso.org/obp
3.1
ropes course
constructed facility with restricted access and requiring supervision consisting of one or more activity
systems, support systems and, if needed, an appropriate safety system
[SOURCE: !EN 15567-1:2015+A1:2020", 3.1 modified: Note 1 deleted]
3.2
individual safety system
ISS
component(s) connecting the harness to the safety line for protection against fall from height consisting
of mobile connecting device(s), lanyard(s) and a connecting system to the harness which may be
supplied as a pre-assembled product, or supplied by one or more manufacturer(s) and may be
assembled by a user to make an ISS
EXAMPLE See Figure 1
Key
1 safety line
2 mobile connecting device
3 lanyard
4 connecting system to the harness
5 harness
Figure 1 — Example of ISS
3.3
safety line
flexible or rigid, horizontal, vertical or sloping, continuous or discontinuous device used as a protection
against falling from a height
Note 1 to entry: In this standard, any part of a rope course where the mobile connecting device (MCD) is intended
to be connected is considered as safety line (e.g. safety line, anchor point, fall arrester, integrated trolley/rail
systems).
[SOURCE: !EN 15567-1:2015+A1:2020", 3.13, modified: Note 1 included]
3.4
mobile connecting device
MCD
part of the ISS which is used to connect it to the safety line and allows the user to move along the safety
line
EXAMPLE Shuttles, pulleys, connectors.
3.5
lanyard
part of the ISS connecting the MCD to the connecting system to the harness
3.6
category A MCD
self-closing device which is not automatically self-locking
EXAMPLE Self-closing or screw gate connector.
3.7
category B MCD
self-locking device
EXAMPLE Self-locking connector.
3.8
category C MCD
interlocking device designed to reduce the likelihood of unintentional detaching from the safety system
3.9
category D MCD
interlocking device designed to prevent unintentional detaching from the safety system
3.10
category E MCD
device that is permanently attached during operation and can only be opened with a tool
3.11
connecting system to the harness
device which connects the lanyard to the harness
3.12
safety line su
...