iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 848-2:2007+A1:2009/FprA2

(Amendment)

Safety of woodworking machines - One side moulding machines with rotating tool - Part 2: Single spindle hand fed/integrated fed routing machines

Safety of woodworking machines - One side moulding machines with rotating tool - Part 2: Single spindle hand fed/integrated fed routing machines

This document specifies all significant hazards, hazardous situations and events as listed in Clause 4 which are relevant to stationary and displaceable single spindle hand fed/integrated fed routing machines with fixed head but allowing only movement along the axis of the tool during machining hereinafter referred to as "machines" designed to cut solid wood, chip board, fibreboard, plywood and also these materials if they are covered with plastic laminate, edgings or veneer when they are used as intended and under the conditions foreseen by the manufacturer. This document does not apply to inverted pin routers and radial arm routers (machines where the work piece is fixed and the tool head is manually moved); NC boring machines and NC routing machines; hand-held routers or any adaptation permitting their use in a different mode, e.g. bench mounting; routing machines set up on a bench or a table similar to a bench, which are intended to carry out work in a stationary position, capable of being lifted by one person by hand. The bench can also be an integrated part of the machine if it consists of hinged legs which can be extended down. This document is not applicable to single spindle hand fed/integrated fed routing machines which are manufactured before the date of its publication as EN.

Sicherheit von Holzbearbeitungsmaschinen - Fräsmaschinen für einseitige Bearbeitung mit drehendem Werkzeug - Teil 2: Einspindelige Oberfräsmaschinen mit Handvorschub/mechanischem Vorschub

Sécurité des machines pour le travail du bois - Machines à fraiser sur une face à outil rotatif - Partie 2: Perceuses et défonceuses monobroche à avance manuelle/mécanisée

Varnost lesnoobdelovalnih strojev - Rezkalni stroji z vrtečim orodjem za enostransko obdelavo - 2. del: Enovretenski rezkalni stroji z ročnim/mehanskim podajanjem

General Information

Status
Not Published
ICS
79.120.10 - Woodworking machines
Technical Committee
CEN/TC 142 - Woodworking machines - Safety
Drafting Committee
CEN/TC 142/WG 5 - Spindle moulding, routing machines and machine centres
Current Stage
5060 - Closure of Vote - Formal Approval
Start Date
12-Jul-2012
Completion Date
12-Jul-2012
Directive
2006/42/EC - Directive 2006/42/EC of the European Parliament and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast)
Mandate
M/396 - Mandate to CEN and Cenelec for standardisation in the field of machinery
Ref Project
SIST EN 848-2:2007+A1:2010/kFprA2:2012 - Safety of woodworking machines - One side moulding machines with rotating tool - Part 2: Single spindle hand fed/integrated fed routing machines

Relations

Merged Into
EN 848-2:2007+A2:2012 - Safety of woodworking machines - One side moulding machines with rotating tool - Part 2: Single spindle hand fed/integrated fed routing machines
Effective Date
01-Aug-2012
Amends
EN 848-2:2007+A1:2009 - Safety of woodworking machines - One side moulding machines with rotating tool - Part 2: Single spindle hand fed/integrated fed routing machines
Effective Date
17-Jul-2010

Buy Standard

EN 848-2:2007+A1:2010/kFprA2:2012EN 848-2:2007+A1:2010/kFprA2:2012
PreviousNext
Draft
EN 848-2:2007+A1:2010/kFprA2:2012
English language
22 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-junij-2012
9DUQRVWOHVQRREGHORYDOQLKVWURMHY5H]NDOQLNL]YUWHþLPRURGMHP]DHQRVWUDQVNR
REGHODYRGHO(QRYUHWHQVNLUH]NDOQLVWURML]URþQLPPHKDQVNLPSRGDMDQMHP
Safety of woodworking machines - One side moulding machines with rotating tool - Part
2: Single spindle hand fed/integrated fed routing machines
Sicherheit von Holzbearbeitungsmaschinen - Fräsmaschinen für einseitige Bearbeitung
mit drehendem Werkzeug - Teil 2: Einspindelige Oberfräsmaschinen mit
Handvorschub/mechanischem Vorschub
Sécurité des machines pour le travail du bois - Machines à fraiser sur une face à outil
rotatif - Partie 2: Perceuses et défonceuses monobroche à avance manuelle/mécanisée
Ta slovenski standard je istoveten z: EN 848-2:2007+A1:2009/FprA2
ICS:
79.120.10 Lesnoobdelovalni stroji Woodworking machines
SIST EN 848- en,fr,de
2:2007+A1:2010/kFprA2:2012
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
FINAL DRAFT
EN 848-2:2007+A1:2009
NORME EUROPÉENNE
EUROPÄISCHE NORM
FprA2
April 2012
ICS 79.120.10
English Version
Safety of woodworking machines - One side moulding machines
with rotating tool - Part 2: Single spindle hand fed/integrated fed
routing machines
Sécurité des machines pour le travail du bois - Machines à Sicherheit von Holzbearbeitungsmaschinen -
fraiser sur une face à outil rotatif - Partie 2: Perceuses et
Fräsmaschinen für einseitige Bearbeitung mit drehendem
défonceuses monobroche à avance manuelle/mécanisée Werkzeug - Teil 2: Einspindelige Oberfräsmaschinen mit
Handvorschub/mechanischem Vorschub
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 142.
This draft amendment A2, if approved, will modify the European Standard EN 848-2:2007+A1:2009. If this draft becomes an amendment,
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration.

This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has
the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2012 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 848-2:2007+A1:2009/FprA2:2012: E
worldwide for CEN national Members.

Contents Page
Foreword .4
1 Modifications to Clause 1, Scope .5
2 Modifications to Clause 2, Normative references .5
3 Modification to 3.2, Definitions .6
4 Modifications to Clause 4, List of significant hazards .7
5 Modifications to 5.1, General . 10
6 Modifications to 5.2.1.1, General . 10
7 Modification to 5.2.1.2, Use of well tried components . 11
8 Modification to 5.2.3, Starting . 11
9 Modifications to 5.2.4, Normal stopping . 11
10 Modifications to 5.2.5, Additional stop . 11
11 Modifications to 5.2.6, Emergency stop . 12
12 Modifications to 5.2.7, Mode selection . 12
13 Modifications to 5.2.8, Spindle speed monitoring . 12
14 Modification to 5.2.9, Integrated feed . 13
15 Modification to 5.3.1, Stability . 13
16 Modification to 5.3.3.1, Tools . 13
17 Modifications to 5.3.3.3.2, Height adjustments . 13
18 Modifications to 5.3.4.1, General . 14
19 Modifications to 5.3.4.2, Brake release . 14
20 Modification to 5.3.5, Device to minimise the possibility or the effect of ejection . 15
21 Modification to 5.3.6.1, General . 15
22 Modification to5.3.6.2, Workpiece guiding for straight work . 15
23 Modification to 5.3.6.3, Workpiece guiding for shaped work . 16
24 Modification to 5.3.7.1.2, Ring guard . 16
25 Modification to 5.3.7.1.4, Safeguarding for straight work . 16
26 Modifications to 5.3.7.2, Guarding of drives . 16
27 Modifications to 5.3.8, Characteristics of guards . 17
28 Modification to 5.3.9, Clamping device . 17
29 Modification to 5.3.10, Safety appliances . 17
30 Modifications of 5.4.2.2, Noise emission measurement . 17
31 Modifications to 5.4.3, Emission of chips and dust . 17
32 Modifications to 5.4.4, Electricity . 18
33 Modification to 6.2, Marking . 18
34 Modifications to 6.3, Instruction handbook . 18
35 Deletion of Annex A . 19
36 Addition of a new normative Annex C, Impact test method for guards . 19
37 Deletion of Annex ZA . 21
38 Modification to Annex ZB . 21
39 Modifications to Bibliography . 22

Foreword
This document (EN 848-2:2007+A1:2009/FprA2:2012) has been prepared by Technical Committee
CEN/TC 142 “Woodworking machines - Safety”, the secretariat of which is held by UNI.
This document is currently submitted to the Unique Acceptance Procedure.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of the Machinery Directive.
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document.
1 Modifications to Clause 1, Scope
st
Add at the end of 1 paragraph "including reasonably foreseeable misuse".
st
Add after 1 paragraph: "Machines which are designed to work wood based materials may also be used for
working hardened plastic materials with similar physical characteristics as wood".
Replace reference to EN 848-3:2007 with EN 848-3:2007+A2:2009.
2 Modifications to Clause 2, Normative references
Add the following reference:
"EN 61800-5-2:2007, Adjustable speed electrical power drive systems – Part 5-2: Safety requirements –
Functional (IEC 61800-5-2:2007)",
"EN ISO 4413:2010, Hydraulic fluid power — General rules and safety requirements for systems and their
components (ISO 4413:2010)
EN ISO 4414:2010, Pneumatic fluid power — General rules and safety requirements for systems and their
components (ISO 4414:2010)".
Delete reference to EN 982:1996, EN 983:1996, EN ISO 11202:1995/AC:1997, EN ISO 11204:1995/AC 1997
and EN ISO 11688-1/1998/AC:1998.
Replace "EN ISO 3743-1:1995" with "EN ISO 3743-1:2010" and replace the title with "Acoustics —
Determination of sound power levels and sound energy levels of noise sources using sound pressure —
Engineering methods for small movable sources in reverberant fields — Part 1: Comparison method for a
hard-walled test room (ISO 3743-1:2010)".
Replace "EN ISO 3744:1995" with "EN ISO 3744:2010" and replace the title with "Acoustics — Determination
of sound power levels and sound energy levels of noise sources using sound pressure — Engineering
methods for an essentially free field over a reflecting plane (ISO 3744:2010)".
Replace "EN ISO 3746:1995" with "EN ISO 3746:2010" and replace the title with "Acoustics — Determination
of sound power levels and sound energy levels of noise sources using sound pressure — Survey method
using an enveloping measurement surface over a reflecting plane (ISO 3746:2010)".
Replace "EN ISO 11202:1995" with "EN ISO 11202:2010" and replace the title with "Acoustics — Noise
emitted by machinery and equipment — Determination of emission sound pressure levels at a work station
and at other specified positions applying approximate environmental corrections (ISO 11202:2010)".
Replace "EN ISO 11204:1995" with "EN ISO 11204:2010" and replace the title with "Acoustics — Noise
emitted by machinery and equipment — Determination of emission sound pressure levels at a work station
and at other specified positions applying accurate environmental corrections (ISO 11204:2010)".
Replace "EN ISO 12100-1:2003" and "EN ISO 12100-2:2003" with "EN ISO 12100:2010, Safety of machinery
— General principles for design — Risk assessment and risk reduction (ISO 12100:2010)".
Replace throughout the standard reference to:
"EN 847-1:2005" with "EN 847-1:2005+A1:2007",
"EN 894-1:1997" with "EN 894-1:1997+A1:2008",
"EN 894-2:1997" with "EN 894-2:1997+A1:2008",
"EN 894-3:2000" with "EN 894-3:2000+A1:2008",
"EN 982:1996" with "EN ISO 4413:2010",
"EN 983:1996" with "EN ISO 4414:2010",
"EN 1005-1:2001" with "EN 1005-1:2001+A1:2008",
"EN 1005-2:2003" with "EN 1005-2:2003+A1:2008",
"EN 1005-3:2002" with "EN 1005-3:2002+A1:2008",
"EN 1005-4:2005" with "EN 1005-4:2005+A1:2008",
"EN 1037:1995" with "EN 1037:1995+A1:2008",
"EN 1088:1995" with "EN 1088:1995+A2:2008",
"EN 60439-1:1999" with "EN 60439-1:1999 and EN 60439-1:1999/A1:2004" in the text excluding Clause 2,
"EN 60529:1991" with "EN 60529:1991 and EN 60529:1991/A1 2000" in the text excluding Clause 2,
"EN ISO 3743-1:1995" with "EN ISO 3743-1:2010",
"EN ISO 3743-2:1996" with "EN ISO 3743-2:2009",
"EN ISO 3744:1995" with "EN ISO 3744:2010",
"EN ISO 3745:2003" with "EN ISO 3745:2009",
"EN ISO 3746:1995" with "EN ISO 3746:2010",
"EN ISO 4871:1996" with "EN ISO 4871:2009",
"EN ISO 9614-1:1995" with "EN ISO 9614-1:2009",
"EN ISO 11202:1995" with "EN ISO 11202:2010",
"EN ISO 11204:1995" with "EN ISO 11204:2010",
"EN ISO 11688-1:1998" with "EN ISO 11688-1:2009",
"EN ISO 12100-1:2003" and "EN ISO 12100-2:2003" with "EN ISO 12100:2010" and
"EN ISO 13850:2006" with "EN ISO 13850:2008".
3 Modification to 3.2, Definitions
Add the following term and definition:
"3.2.19
performance level PL
discrete level used to specify the ability of safety-related parts of control systems to perform a safety function
under foreseeable conditions
[EN ISO 13849-1:2008, 3.1.23]
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 19085-4:2024(Main)
Woodworking machines - Safety - Part 4: Vertical panel circular sawing machines (ISO 19085-4:2024)
SIST EN ISO 19085-4:2025

This document specifies the safety requirements and measures for manually loaded and unloaded vertical panel circular sawing machines (defined in 3.1) capable of continuous production use, with hand feed or integrated feed, hereinafter referred to also as “machines”.
This document deals with all significant hazards, hazardous situations and events, as listed in Annex A, relevant to the machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer, including reasonably foreseeable misuse. Transport, assembly, dismantling, disabling and scrapping phases are also taken into account.
This document is also applicable to machines fitted with one or more of the following devices/additional working units, whose hazards have been dealt with:
—     an integrated feed device;
—     a device for scoring;
—     an angle cutting device;
—     a middle support device;
—     programmable end stops for parallel vertical cuts;
—     a device for grooving with a milling tool with a cutting width not exceeding 27 mm;
—     a panel pusher;
—     a panel lowering device;
—     stop devices for workpiece during horizontal cuts.
The machines are designed for cutting panels consisting of:
a)       solid wood;
b)       material with similar physical characteristics to wood (see ISO 19085-1:2021, 3.2);
c)        composite materials with core consisting, for example, of polyurethane or mineral material laminated with light alloy;
d)       polymer-matrix composite materials and reinforced thermoplastic/thermoset/elastomeric materials;
e)       gypsum boards, gypsum bounded fibreboards;
f)         honeycomb aluminium boards;
g)       matrix engineered mineral boards, silicate boards;
h)       aluminium light alloy plates;
i)         composite boards made from the materials listed above.
This document does not apply to machines
—     with pressure beam and saw unit mounted behind the workpiece support,
—     where the guide rails on which the saw unit moves vertically are fixed on the machine frame and the horizontal cut can only be made by manually feeding the panel,
—     designed to cut in vertical direction only,
—     automatically performing two or more cutting cycles in sequence,
—     intended for use in potentially explosive atmosphere, and
—     manufactured prior to the publication of this document.

  • Draft
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 19085-9:2024(Main)
Woodworking machines - Safety - Part 9: Circular saw benches (with and without sliding table) (ISO 19085-9:2024)
SIST EN ISO 19085-9:2025

This document specifies the safety requirements and measures for circular saw benches with or without sliding table or demountable power feed unit or both and capable of continuous production use, also known as “table saws” (in the USA), hereinafter referred to also as “machines”.
The machines are designed to cut solid wood and material with similar physical characteristics to wood (see ISO 19085-1:2021, 3.2).
This document deals with all significant hazards, hazardous situations and events as listed in Annex A relevant to the machines when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer; reasonably foreseeable misuse has been considered too. Transport, assembly, dismantling, disabling and scrapping phases have also been taken into account.
This document is also applicable to machines fitted with one or more of the following devices or working units, whose hazards have been dealt with:
—     device for the main saw blade and scoring saw blade to be raised and lowered through the table;
—     device to tilt the main saw blade and scoring saw blade for angled cutting;
—     device for scoring;
—     device for grooving with milling tool with a width not exceeding 20 mm in one pass;
—     demountable power feed unit;
—     additional manually operated sliding table;
—     powered workpiece clamping device.
This document does not apply to:
a)       machines intended for outdoor use on building sites;
NOTE            Building site saws (contractor saws) are covered by the requirements of ISO 19085-10:2018.
b)       handheld woodworking machines including any adaptation permitting their use in a different mode, i.e. bench mounting;
c)        machines intended for use in a potentially explosive atmosphere;
d)       machines manufactured prior to the publication of this document.

  • Draft
    59 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 19085-5:2024(Main)
Woodworking machines - Safety - Part 5: Dimension saws (ISO 19085-5:2024)
SIST EN ISO 19085-5:2025

This document specifies the safety requirements and measures for dimension saws (defined in 3.1), capable of continuous production use and hereinafter referred to also as “machines”.
The machines are designed to cut solid wood and material with similar physical characteristics to wood.
This document deals with all significant hazards, hazardous situations and events, listed in Annex A, relevant to the machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer; reasonably foreseeable misuse has been considered too. Transport, assembly, dismantling, disabling and scrapping phases have also been taken into account.
This document is also applicable to machines fitted with one or more of the following devices/additional working units, whose hazards have been dealt with:
a)       device to raise and lower the main saw blade and scoring saw blade;
b)       device to tilt the main saw blade and scoring saw blade for angled cutting in one or both directions;
c)        device for scoring;
d)       device for grooving with milling tool with a width not exceeding 20 mm;
e)       demountable power feed unit;
f)         power-operated sliding table;
g)       workpiece clamping.
This document is not applicable to machines intended for use in potentially explosive atmospheres or to machines manufactured prior to the date of its publication.

  • Draft
    66 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 19085-7:2024(Main)
Woodworking machines - Safety - Part 7: Surface planing, thickness planing and combined surface/thickness planing machines (ISO 19085-7:2024)
SIST EN ISO 19085-7:2024

This document specifies the safety requirements and measures for
—     surface planing machines, also called jointers,
—     thickness planing machines, also called planers or single surface planers, and
—     combined surface/thickness planing machines
with fixed cutter block position, with an integrated feed in thickness planing mode, with or without demountable power feed device in planing mode, with manual loading and/or unloading of the workpiece, and capable of continuous production use, altogether referred to as “machines”.
The machines are designed to cut solid wood and material with similar physical characteristics to wood (see ISO 19085-1:2021, 3.2).
This document deals with all significant hazards, hazardous situations and events as listed in Annex A relevant to the machines when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer. Reasonably foreseeable misuse has been considered too. Transport, assembly, dismantling, disabling and scrapping phases have also been taken into account.
This document is also applicable to surface planing machines and combined surface/thickness planing machines fitted with an optional mortising device, whose hazards have been dealt with.
This document does not apply to:
a)       machines with more than one cutter block;
b)       machines with a mortising unit driven by a separate motor;
c)        machines where the cutter block is adjustable for depth of cut setting in thickness planing mode;
d)       machines where the conversion from planing to thickness planing mode or vice versa is achieved by mounting or demounting parts/units;
e)       machines where surface planing and thickness planing can be performed at the same time;
f)         machines intended for use in potentially explosive atmosphere;
g)       machines manufactured prior to the publication of this document.

  • Draft
    56 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 19085-11:2024(Main)
Woodworking machines - Safety - Part 11: Combined machines (ISO 19085-11:2024)
SIST EN ISO 19085-11:2024

This document specifies the safety requirements and measures for combined woodworking machines (defined in 3.1), capable of continuous production use, with manual loading and unloading of the workpiece and hereinafter referred to also as “machines”.
The machines are designed to cut solid wood and material with similar physical characteristics to wood (see ISO 19085-1:2021, 3.2).
This document deals with all significant hazards, hazardous situations and events, listed in Annex A, relevant to the machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer; reasonably foreseeable misuse has been considered too. Transport, assembly, dismantling, disabling and scrapping phases have also been taken into account.
This document applies to machines also equipped with the devices or additional working units listed in the Scopes of ISO 19085-5:2024, ISO 19085-6:2024, ISO 19085-7:2024 and ISO 19085-9:2024.
This document does not apply to:
a)       machines incorporating a planing unit and a mortising device only;
NOTE            Machines incorporating a planing unit and a mortising device only are dealt with in ISO 19085-7:2024.
b)       combined machines incorporating a band saw unit;
c)        machines with a mortising unit with a separate drive other than the planing unit drive;
d)       machines intended for use in potentially explosive atmosphere;
e)       machines manufactured before the publication of this document.

  • Draft
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 19085-8:2024(Main)
Woodworking machines - Safety - Part 8: Wide belt sanding machines and surface treating machines (ISO 19085-8:2024)
SIST EN ISO 19085-8:2024

This document specifies the safety requirements and measures for wide belt sanding machines (defined in 3.1) and for surface treating machines (defined in 3.2) capable of continuous production use, altogether referred to as “machines”.
This document deals with all significant hazards, hazardous situations and events, as listed in Annex A, relevant to the machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer, including reasonably foreseeable misuse. Transport, assembly, dismantling, disabling and scrapping phases are also taken into account.
This document is also applicable to machines fitted with one or more of the following devices/additional working units, whose hazards have been dealt with:
—     transversal sanding unit;
—     cleaning brushing unit;
—     satining roller unit;
—     disk brushing unit;
—     texturing brushing roller unit;
—     texturing brushing belt unit;
—     cutterblock unit;
—     texturing band saw unit;
—     spiked roller unit;
—     multi blade unit;
—     conveyor directly controlled by the machine;
—     additional workpiece vacuum clamping device;
—     antistatic bar unit.
NOTE 1        An antistatic bar is a device that eliminates electrostatic charges on the workpiece to ease its subsequent cleaning from dust by airflow.
This document is also applicable to machines fitted with a laser engraving unit, but the specific hazards of this unit have not been dealt with.
The machines are designed to process workpieces with flat surface and even thickness, in shape of panels or beams or frames, consisting of:
a)       solid wood;
b)       material with similar physical characteristics to wood (see ISO 19085-1:2021, 3.2);
c)        gypsum boards, gypsum bounded fibreboards;
d)       composite materials with core consisting of, e.g. polyurethane or mineral material;
e)       composite boards made from the materials listed above;
f)         all materials listed above, already lacquered.
This document does not deal with hazards related to:
—     specific devices other than those listed above;
—     access through in-feed and out-feed openings of machines with a work piece height capacity greater than 700 mm;
—     systems for powered loading or unloading, or both, of the workpiece to or from a single machine;
NOTE 2        Loading the machine manually includes manually placing the workpiece onto a conveyor directly controlled by the machine. Unloading the machine manually includes manually removing the workpiece from a conveyor directly controlled by the machine.
—     out-feed workpieces on machines with feed speed higher than 60 m/min;
—     interfacing of the machine with any other machine.
This document is not applicable to machines intended for use in a potentially explosive atmosphere and to machines manufactured prior to the date of its publication.

  • Draft
    42 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 19085-6:2024(Main)
Woodworking machines - Safety - Part 6: Single spindle vertical moulding machines (toupie) (ISO 19085-6:2024)
SIST EN ISO 19085-6:2024

This document specifies the safety requirements and measures for single spindle vertical moulding machines (defined in 3.1), capable of continuous production use and hereinafter referred to also as “machines”.
The machines are designed to cut solid wood and material with similar physical characteristics to wood.
This document deals with all significant hazards, hazardous situations and events as listed in Annex A, relevant to the machines when they are operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Transport, assembly, dismantling, disabling and scrapping phases have also been taken into account.
This document is also applicable to machines fitted with one or more of the following devices/additional working units, whose hazards have been dealt with:
a)       device to adjust the arbor vertically;
b)       device to tilt the arbor;
c)        device to fit a manually operated tenoning sliding table;
d)       glass bead saw unit;
e)       adjustable table insert;
f)         device for changing the direction of rotation of the spindle;
g)       device for fixing shank mounted tools on the arbor;
h)       interchangeable arbor;
i)         quick tool/arbor change system;
j)         demountable power feed unit;
k)       support for the demountable power feed unit with power-driven adjustments.
This document does not apply to
—     machines equipped with outboard bearings,
—     machines equipped with powered movements of a front extension table and/or a tenoning sliding table.
This document is not applicable to machines intended for use in potentially explosive atmospheres or to machines manufactured prior to the date of its publication.

  • Standard
    71 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 19085-12:2021/A11:2023(Amendment)
Woodworking machines - Safety - Part 12: Tenoning/profiling machines (ISO 19085-12:2021)
SIST EN ISO 19085-12:2021/A11:2023
  • Amendment
    5 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 19085-3:2021(Main)
Woodworking machines - Safety - Part 3: Numerically controlled (NC/CNC) boring and routing machines (ISO 19085-3:2021)
SIST EN ISO 19085-3:2022

This document gives the safety requirements and measures for numerically controlled (NC/CNC) boring machines, NC/CNC routing machines and NC/CNC boring and routing machines (as defined in 3.2, 3.3 and 3.4), capable of continuous production use, hereinafter referred to as "machines".
This document deals with all significant hazards, hazardous situations and events, listed in Annex A, relevant to the machines when they are operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also, transport, assembly, dismantling, disabling and scrapping phases have been taken into account.
This document is also applicable to machines fitted with one or more of the following devices/additional working units, whose hazards have been dealt with:
—    additional working units for sawing, sanding, assembling or dowel inserting;
—    fixed or movable workpiece support;
—    mechanical, pneumatic, hydraulic or vacuum workpiece clamping;
—    automatic tool change devices.
It is also applicable to machines fitted with edge-banding equipment, even if the relevant specific hazards have not been dealt with.
NOTE      For the risk assessment needed for the edge-banding equipment, ISO 19085-17 can be useful.
Machines covered in this document are designed for workpieces consisting of:
—    solid wood;
—    material with similar physical characteristics to wood (see ISO 19085-1:2021, 3.2);
—    gypsum boards, gypsum bounded fibreboards, cardboard;
—    matrix engineered mineral boards, silicate boards;
—    composite materials with core consisting of polyurethane or mineral material laminated with light alloy;
—    polymer-matrix composite materials and reinforced thermoplastic/thermoset/elastomeric materials;
—    aluminium light alloy profiles;
—    aluminium light alloy plates with a maximum thickness of 10 mm;
—    composite boards made from the materials listed above.
This document does not deal with specific hazards related to:
—    use of grinding wheels;
—    ejection through openings guarded by curtains on machines where the height of the opening in the enclosure above the workpiece support exceeds 700 mm;
—    ejection due to failure of milling tools with a cutting circle diameter equal to or greater than 16 mm and sawing tools not conforming to EN 847‑1:2017 and EN 847‑2:2017;
—    the combination of a single machine being used with other machines (as a part of a line);
—    integrated workpiece loading/unloading systems (e.g. robots).
This document is not applicable to:
—    single spindle hand fed or integrated fed routing machines;
—    machines intended for use in potentially explosive atmosphere;
—    machines manufactured prior to its publication.

  • Standard
    96 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 19085-16:2021(Main)
Woodworking machines - Safety - Part 16: Table band saws and band re-saws (ISO 19085-16:2021)
SIST EN ISO 19085-16:2022

This document gives the safety requirements and measures for table band saws and band resaws, with manual loading and/or unloading and suitable for continuous production use, hereinafter referred to as “machines”.
The machines are designed to cut solid wood and material with similar physical characteristics to wood.
It deals with all significant hazards, hazardous situations and events, listed in Annex A, relevant to the machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer; reasonably foreseeable misuse has been considered too. Also, transport, assembly, dismantling, disabling and scrapping phases have been taken into account.
It is also applicable to machines fitted with one or more of the following devices/additional working units, whose hazards have been dealt with:
a) device to tilt the table;
b) device to tilt the saw unit.
This document does not apply to:
1)    machines driven by combustion engines or power take offs (PTO);
2)    log band sawing machines;
NOTE Log band sawing machines are covered by EN 1807-2:2013.
3)    horizontal band saws and band resaws;
4)    machines designed for cross-cutting of firewood.
This document does not deal with hazards related to the combination of a single machine being used with any other machine (as part of a line).
This document is not applicable to machines intended for use in potentially explosive atmospheres or to machines manufactured prior to the date of its publication.

  • Standard
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day