EN ISO 13517:2013

SLOVENSKI STANDARD
01-marec-2014
Kovinski prah - Ugotavljanje hitrosti pretoka z uporabo kalibriranega lija (merilnik
pretoka po Gustavssonu) (ISO 13517:2013)
Metallic powders - Determination of flowrate by means of a calibrated funnel
(Gustavsson flowmeter) (ISO 13517:2013)
Metallpulver - Ermittlung der Durchflussrate mit Hilfe eines kalibrierten Trichters
(Gustavsson flowmeter) (ISO 13517:2013)
Poudres métalliques - Détermination du temps d'écoulement au moyen d'un entonnoir
calibré (cône d'écoulement de Gustavsson) (ISO 13517:2013)
Ta slovenski standard je istoveten z: EN ISO 13517:2013
ICS:
77.160 Metalurgija prahov Powder metallurgy
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 13517
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2013
ICS 77.160
English Version
Metallic powders - Determination of flowrate by means of a
calibrated funnel (Gustavsson flowmeter) (ISO 13517:2013)
Poudres métalliques - Détermination du temps Metallpulver - Ermittlung der Durchflussrate mit Hilfe eines
d'écoulement au moyen d'un entonnoir calibré (cône kalibrierten Trichters (Gustavsson flowmeter) (ISO
d'écoulement de Gustavsson) (ISO 13517:2013) 13517:2013)
This European Standard was approved by CEN on 1 March 2013.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2013 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 13517:2013: E
worldwide for CEN national Members.

Contents Page
Foreword .3

Foreword
This document (EN ISO 13517:2013) has been prepared by Technical Committee ISO/TC 119 "Powder
metallurgy".
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by November 2013, and conflicting national standards shall be withdrawn
at the latest by November 2013.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 13517:2013 has been approved by CEN as EN ISO 13517:2013 without any modification.

INTERNATIONAL ISO
STANDARD 13517
First edition
2013-05-01
Metallic powders — Determination
of flowrate by means of a calibrated
funnel (Gustavsson flowmeter)
Poudres métalliques — Détermination du temps d’écoulement au
moyen d’un entonnoir calibré (cône d’écoulement de Gustavsson)
Reference number
ISO 13517:2013(E)
©
ISO 2013
ISO 13517:2013(E)
© ISO 2013
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2013 – All rights reserved

ISO 13517:2013(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Principle . 1
3 Apparatus . 1
4 Calibration of the funnel. 2
4.1 Calibration by the manufacturer of the funnel . 2
4.2 Calibration by the user of the funnel. 3
5 Sampling . 3
6 Procedure. 3
7 Expression of results . 4
8 Precision . 4
9 Test report . 5
Bibliography . 6
ISO 13517:2013(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International
Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies
casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying an
...