EN ISO 21809-5:2017
(Main)Petroleum and natural gas industries - External coatings for buried or submerged pipelines used in pipeline transportation systems - Part 5: External concrete coatings (ISO 21809-5:2017)
Petroleum and natural gas industries - External coatings for buried or submerged pipelines used in pipeline transportation systems - Part 5: External concrete coatings (ISO 21809-5:2017)
ISO 21809-5:2017 specifies the requirements for qualification, application, testing and handling of materials required for the application of reinforced concrete coating externally to either bare pipe or pre-coated pipe for use in pipeline transportation systems for the petroleum and natural gas industries as defined in ISO 13623.
The external application of concrete is primarily used for the negative buoyancy of pipes used in buried or submerged pipeline systems and/or for the mechanical protection of the pipe and its pre-coating.
ISO 21809-5:2017 is applicable to concrete thicknesses of 25 mm or greater.
Erdöl- und Erdgasindustrie - Umhüllungen für erd- und wasserverlegte Rohrleitungen in Transportsystemen -Teil 5: Betonummantelungen (ISO 21809-5:2017)
Dieses Dokument legt die Anforderungen an die Qualifizierung, Anwendung, Prüfung und den Umschlag von Werkstoffen fest, die für die Anwendung von bewehrten Betonumhüllungen bei Glattrohren oder vorbeschichteten Rohren für den Einsatz in Rohrleitungen von Transportsystemen der Erdöl- und Erdgasindustrie, wie in ISO 13623 definiert, erforderlich sind.
Die äußere Aufbringung von Beton dient hauptsächlich dazu, für Abtriebssicherheit der in erd- oder wasserverlegten Rohrleitungssystemen verwendeten Rohre und/oder für den mechanischen Schutz des Rohrs und seiner Umhüllung zu sorgen.
Dieses Dokument gilt für Betondicken größer oder gleich 25 mm.
Industries du pétrole et du gaz naturel - Revêtements externes des conduites enterrées ou immergées utilisées dans les systèmes de transport par conduites - Partie 5: Revêtements externes en béton (ISO 21809-5:2017)
L'ISO 21809-5:2017 spécifie les exigences relatives à la qualification, à la mise en ?uvre, aux essais et à la manutention des matériaux requis pour l'application d'un revêtement extérieur en béton armé sur des tubes en acier nus ou pré-revêtus, utilisés dans les systèmes de transport par conduites pour les industries du pétrole et du gaz naturel tels que définis dans l'ISO 13623.
L'application extérieure de béton est principalement utilisée pour empêcher la flottabilité des tubes utilisés dans les systèmes de conduites enterrées et immergées et/ou pour la protection mécanique du tube et de son pré-revêtement.
L'ISO 21809-5:2017 s'applique aux épaisseurs de béton supérieures ou égales à 25 mm.
Naftna industrija in industrija zemeljskega plina - Zunanje prevleke za cevovode, zakopane v zemljo ali potopljene v vodo, v sistemih cevovodnega transporta - 5. del: Zunanje betonske prevleke (ISO 21809-5:2017)
V tem dokumentu so določene zahteve za usposobljenost, uporabo, testiranje in ravnanje z materiali, ki so potrebni za nanašanje armiranega betonskega premaza na zunanji strani bodisi na golo cev ali v predhodno obloženo cev za uporabo v cevovodnih transportnih sistemih za naftno industrijo in industrijo zemeljskega plina
kot je opredeljeno v standardu ISO 13623.
Zunanji nanos betona se primarno uporablja za negativno plovnost cevi, ki se uporablja v pokopanih ali potopljenih cevovodnih sistemih in/ali za mehansko zaščito cevi in njenega predhodnega premaza.
Ta dokument velja za beton debeline 25 mm ali več.
General Information
Relations
Related Packages
Standards Content (Sample)
SLOVENSKI STANDARD
01-oktober-2017
1DGRPHãþD
SIST EN ISO 21809-5:2010
Naftna industrija in industrija zemeljskega plina - Zunanje prevleke za cevovode,
zakopane v zemljo ali potopljene v vodo, v sistemih cevovodnega transporta - 5.
del: Zunanje betonske prevleke (ISO 21809-5:2017)
Petroleum and natural gas industries - External coatings for buried or submerged
pipelines used in pipeline transportation systems - Part 5: External concrete coatings
(ISO 21809-5:2017)
Industries du pétrole et du gaz naturel - Revêtements externes des conduites enterrées
ou immergées utilisées dans les systèmes de transport par conduites - Partie 5:
Revêtements externes en béton (ISO 21809-5:2017)
Ta slovenski standard je istoveten z: EN ISO 21809-5:2017
ICS:
25.220.99 Druge obdelave in prevleke Other treatments and
coatings
75.200 2SUHPD]DVNODGLãþHQMH Petroleum products and
QDIWHQDIWQLKSURL]YRGRYLQ natural gas handling
]HPHOMVNHJDSOLQD equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 21809-5
EUROPEAN STANDARD
NORME EUROPÉENNE
August 2017
EUROPÄISCHE NORM
ICS 75.200 Supersedes EN ISO 21809-5:2010
English Version
Petroleum and natural gas industries - External coatings
for buried or submerged pipelines used in pipeline
transportation systems - Part 5: External concrete coatings
(ISO 21809-5:2017)
Industries du pétrole et du gaz naturel - Revêtements Erdöl- und Erdgasindustrie - Umhüllungen für erd- und
externes des conduites enterrées ou immergées wasserverlegte Rohrleitungen in Transportsystemen -
utilisées dans les systèmes de transport par conduites - Teil 5: Betonummantelungen (ISO 21809-5:2017)
Partie 5: Revêtements externes en béton (ISO 21809-
5:2017)
This European Standard was approved by CEN on 25 July 2017.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 21809-5:2017 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 21809-5:2017) has been prepared by Technical Committee ISO/TC 67
“Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries”
in collaboration with Technical Committee ECISS/TC 110 “Steel tubes, and iron and steel fittings” the
secretariat of which is held by UNI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by February 2018 and conflicting national standards shall
be withdrawn at the latest by February 2018.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 21809-5:2010.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 21809-5:2017 has been approved by CEN as EN ISO 21809-5:2017 without any
modification.
INTERNATIONAL ISO
STANDARD 21809-5
Second edition
2017-06
Petroleum and natural gas
industries — External coatings for
buried or submerged pipelines used
in pipeline transportation systems —
Part 5:
External concrete coatings
Industries du pétrole et du gaz naturel — Revêtements externes
des conduites enterrées ou immergées utilisées dans les systèmes de
transport par conduites —
Partie 5: Revêtements externes en béton
Reference number
ISO 21809-5:2017(E)
©
ISO 2017
ISO 21809-5:2017(E)
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved
ISO 21809-5:2017(E)
Contents Page
Foreword .v
Introduction .vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 3
4 Symbols and abbreviated terms . 6
4.1 Symbols . 6
4.2 Abbreviated terms . 6
5 General requirements . 6
5.1 Rounding . 6
5.2 Compliance with this document . 6
6 Information supplied by the purchaser . 7
6.1 General information . 7
6.2 Additional information . 7
7 Materials . 7
7.1 Pipe . 7
7.2 Cement . 8
7.3 Supplementary cementitious materials . 8
7.4 Aggregate — Fine and coarse . 9
7.5 Heavyweight aggregate. 9
7.6 Lightweight aggregate . 9
7.7 Recycled concrete as aggregate .10
7.8 Water .10
7.9 Steel reinforcement .10
7.10 Concrete admixtures .10
7.11 Reclaimed concrete .10
8 Concrete mix .11
9 Coating application .11
9.1 Qualification .11
9.2 Application of concrete coating .13
9.3 Environmental conditions .13
9.4 Pipe .13
9.4.1 Pre-coated pipe .13
9.4.2 Bare pipe .14
9.5 Steel reinforcement .14
9.5.1 General.14
9.5.2 Cage reinforcement .14
9.5.3 Welded wire mesh reinforcement.14
9.5.4 Woven wire mesh reinforcement .14
9.5.5 Reinforcement placement .15
9.6 Concrete cutback .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.