EN 13445-3:2014/prA12
(Amendment)Unfired pressure vessels - Part 3: Design
Unfired pressure vessels - Part 3: Design
This Part of this European Standard specifies requirements for the design of unfired pressure vessels covered by EN 13445-1:2009 and constructed of steels in accordance with EN 13445-2:2009. EN 13445-5:2009, Annex C specifies requirements for the design of access and inspection openings, closing mechanisms and special locking elements. NOTE This Part applies to design of vessels before putting into service. It may be used for in service calculation or analysis subject to appropriate adjustment.
Unbefeuerte Druckbehälter - Teil 3: Konstruktion
Dieser Teil 3 der Europäischen Norm legt die Anforderungen an die Konstruktion von unbefeuerten Druckbehältern
nach EN 13445-1:2014 und hergestellt aus Stählen nach EN 13445-2:2014 fest.
EN 13445-5:2014 gibt im Anhang C Bedingungen für die Konstruktion von Zugangs- und Besichtigungsöffnungen,
von Verschlüssen und besonderen Verschlusselementen.
ANMERKUNG Dieser Teil gilt für Konstruktion und Berechnung von Behältern vor der Inbetriebnahme. Er kann auch, mit
entsprechenden Anpassungen, für Berechnungen oder analytische Nachweise im Betrieb verwendet werden.
Récipients sous pression non soumis à la flamme - Partie 3 : Conception
Cette partie de la présente norme européenne spécifie les exigences relatives à la conception des récipients sous
pression non soumis à la flamme couverts par l’EN 13445-1:2014 et construits en aciers conformes à
l’EN 13445-2:2014.
L’Annexe C de l’EN 13445-5:2014 spécifie les exigences relatives à la conception des ouvertures d’accès et
d’inspection, des mécanismes de fermeture et des éléments de verrouillage spéciaux.
NOTE Cette partie s'applique à la conception des récipients avant mise en service. Elle peut être utilisée pour les calculs
ou l'analyse en service sous réserve d'apporter les ajustements appropriés.
Nekurjene tlačne posode - 3. del: Konstruiranje - Dopolnilo A12
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-julij-2017
1HRJUHYDQH QHNXUMHQH WODþQHSRVRGHGHO .RQVWUXLUDQMH'RSROQLOR$
Unfired pressure vessels - Part 3: Design
Unbefeuerte Druckbehälter - Teil 3: Konstruktion
Récipients sous pression non soumis à la flamme - Partie 3 : Conception
Ta slovenski standard je istoveten z: EN 13445-3:2014/prA12
ICS:
23.020.32 7ODþQHSRVRGH Pressure vessels
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT
EUROPEAN STANDARD
EN 13445-3:2014
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA12
June 2017
ICS 23.020.30
English Version
Unfired pressure vessels - Part 3: Design
Récipients sous pression non soumis à la flamme - Unbefeuerte Druckbehälter - Teil 3: Konstruktion
Partie 3 : Conception
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 54.
This draft amendment A12, if approved, will modify the European Standard EN 13445-3:2014. If this draft becomes an
amendment, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for
inclusion of this amendment into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. I
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.