iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN ISO 9696:2017

(Main)

Water quality - Gross alpha activity - Test method using thick source (ISO 9696:2017)

Water quality - Gross alpha activity - Test method using thick source (ISO 9696:2017)

ISO 9696:2017 specifies a method for the determination of gross alpha activity in non-saline waters for alpha-emitting radionuclides which are not volatile up to 350 °C.
The method is applicable to raw and potable waters.
The range of application depends on the amount of total soluble salts in the water and on the performance characteristics (background count rate and counting efficiency) of the counter.
It is the laboratory's responsibility to ensure the suitability of this method for the water samples tested.

Wasserbeschaffenheit - Gesamt-Alpha-Aktivität - Dickschichtverfahren (ISO 9696:2017)

Dieses Dokument legt ein Verfahren zur Bestimmung der Gesamt-Alpha-Aktivität von Alpha-Strahlen emittierenden Radionukliden in nicht-salzhaltigem Wasser fest, die bis zu 350 °C nicht flüchtig sind.
Das Verfahren ist auf Roh- und Trinkwasser anwendbar.
Der Arbeitsbereich hängt von der Menge an gelösten Salzen im Wasser und von der Leistungsfähigkeit (Nulleffektzählrate und Zählausbeute) der Zählvorrichtung ab.
Es liegt in der Verantwortung des Labors sicherzustellen, dass dieses Verfahren für die zu untersuchenden Wasserproben geeignet ist

Qualité de l'eau - Activité alpha globale - Méthode d'essai par source épaisse (ISO 9696:2017)

Le présent document spécifie une méthode de détermination de l'activité alpha globale dans les eaux non salines pour les radionucléides émetteurs alpha qui ne sont pas volatils jusqu'à 350 °C.
La méthode est applicable à l'analyse des eaux brutes et des eaux potables.
La gamme de validité de la méthode dépend de la quantité de sels solubles totaux contenus dans l'eau et des caractéristiques de performance (taux de comptage du bruit de fond et rendement de comptage) du compteur.
Il incombe au laboratoire de s'assurer que cette méthode est adaptée aux échantillons d'eau soumis à essai.

Kakovost vode - Skupna alfa aktivnost - Preskusna metoda robustnega vira (ISO 9696:2017)

Ta mednarodni standard določa metodo za določevanje skupne alfa aktivnosti v neslanih vodah za alfa oddajne radionuklide, ki niso hlapni pri 350 °C. Metoda omogoča določevanje podprtih hlapnih nukleotidov, ki se merijo do meje, določene na podlagi razpolovne dobe, ohranitve matrike (hlapnih nukleotidov) in trajanja meritve (čas štetja). Ta metoda se uporablja za neobdelano in pitno vodo. Območje uporabe je odvisno od količine lebdeče snovi v vodi in od lastnosti števca (stopnja štetja v ozadju in učinkovitost štetja).

General Information

Status
Published
Publication Date
14-Nov-2017
Withdrawal Date
30-May-2018
ICS
13.060.60 - Examination of physical properties of water
17.240 - Radiation measurements
Technical Committee
CEN/TC 230 - Water analysis
Drafting Committee
CEN/TC 230 - Water analysis
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
15-Nov-2017
Completion Date
15-Nov-2017
Ref Project
SIST EN ISO 9696:2018 - Water quality - Gross alpha activity - Test method using thick source (ISO 9696:2017)

Buy Standard

EN ISO 9696:2018EN ISO 9696:2018
PreviousNext
Standard
EN ISO 9696:2018
English language
22 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-januar-2018
1DGRPHãþD
SIST ISO 9696:2010
Kakovost vode - Skupna alfa aktivnost - Preskusna metoda robustnega vira (ISO
9696:2017)
Water quality - Gross alpha activity - Test method using thick source (ISO 9696:2017)
Wasserbeschaffenheit - Gesamt-Alpha-Aktivität - Dickschichtverfahren (ISO 9696:2017)
Qualité de l'eau - Activité alpha globale - Méthode d'essai par source concentrée (ISO
9696:2017)
Ta slovenski standard je istoveten z: EN ISO 9696:2017
ICS:
13.060.60 Preiskava fizikalnih lastnosti Examination of physical
vode properties of water
17.240 Merjenje sevanja Radiation measurements
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 9696
EUROPEAN STANDARD
NORME EUROPÉENNE
November 2017
EUROPÄISCHE NORM
ICS 13.060.60
English Version
Water quality - Gross alpha activity - Test method using
thick source (ISO 9696:2017)
Qualité de l'eau - Activité alpha globale - Méthode Wasserbeschaffenheit - Gesamt-Alpha-Aktivität -
d'essai par source concentrée (ISO 9696:2017) Dickschichtverfahren (ISO 9696:2017)
This European Standard was approved by CEN on 19 September 2017.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 9696:2017 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 9696:2017) has been prepared by Technical Committee ISO/TC 147 "Water
quality" in collaboration with Technical Committee CEN/TC 230 “Water analysis” the secretariat of
which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by May 2018 and conflicting national standards shall be
withdrawn at the latest by May 2018.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 9696:2017 has been approved by CEN as EN ISO 9696:2017 without any modification.
FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 9696
ISO/TC 147/SC 3
Water quality — Gross alpha activity
Secretariat: AFNOR
— Test method using thick source
Voting begins on:
2017­06­22
Qualité de l’eau — Activité alpha globale — Méthode d’essai par
source concentrée
Voting terminates on:
2017­08­17
ISO/CEN PARALLEL PROCESSING
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO­
ISO/FDIS 9696:2017(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN­
DARDS TO WHICH REFERENCE MAY BE MADE IN
©
NATIONAL REGULATIONS. ISO 2017

ISO/FDIS 9696:2017(E)
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH­1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved

ISO/FDIS 9696:2017(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols . 2
5 Principle . 2
6 Reagents and equipment . 3
6.1 Reagents. 3
6.2 Equipment . 4
7 Procedure. 4
7.1 Sampling . 5
7.2 Pretreatment . 5
7.3 Concentration stage . 5
7.4 Sulfation stage . 5
7.5 Ignition stage . 6
7.6 Source preparation . 6
7.7 Measurement . 6
7.8 Background determination . 6
7.9 Preparation of the calibration source. 6
7.10 Sensitivity and bias. 7
7.11 Optimization of the determination . 7
8 Contamination check . 8
8.1 General . 8
8.2 Radon isotopes losses . 8
8.3 Polonium losses . . 8
9 Expression of results . 8
9.1 Calculation of activity concentration . 8
9.2 Standard uncertainty . 9
9.3 Decision threshold . 9
9.4 Detection limit .10
9.5 Confidence-interval limits .10
10 Test report .10
Annex A (informative) Performance criteria .12
Bibliography .13
ISO/FDIS 9696:2017(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non­governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the e
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 13165-1:2024(Main)
Water quality - Radium-226 - Part 1: Test method using liquid scintillation counting (ISO 13165-1:2022)
SIST EN ISO 13165-1:2024

This document specifies the determination of radium-226 (226Ra) activity concentration in non-saline
water samples by extraction of its daughter radon-222 (222Rn) and its measurement using liquid
scintillation analysis.
The test method described in this document, using currently available scintillation counters, has a
detection limit of approximately 50 mBq·l−1. This method is not applicable to the measurement of other
radium isotopes.

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 13164-4:2023(Main)
Water quality - Radon-222 - Part 4: Test method using two-phase liquid scintillation counting (ISO 13164-4:2023)
SIST EN ISO 13164-4:2023

This document describes a test method for the determination of radon-222 (222Rn) activity concentration in non-saline waters by extraction and liquid scintillation counting.
The 222Rn activity concentrations, which can be measured by this test method utilizing currently available instruments, are above 0,5 Bq·l−1 which is the typical detection limit for a 10 ml test sample and a measuring time of 1 h.
It is the responsibility of the laboratory to ensure the validity of this test method for water samples of untested matrices.
Annex A gives indication on the necessary counting conditions to meet the required detection limits for drinking water monitoring.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 13165-2:2022(Main)
Water quality - Radium-226 - Part 2: Test method using emanometry (ISO 13165-2:2022)
SIST EN ISO 13165-2:2023

This document specifies a test method to determine radium-226 (226Ra) activity concentration in all types of water by emanometry.
The test method specified is suitable for the determination of the soluble, suspended and total 226Ra activity concentration in all types of water with soluble 226Ra activity concentrations greater than 0,02 Bq l−1.
The decay chains of 238U and 232Th are given in Annex A. Figure A.1 shows the 238U and its decay chain.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 13163:2022(Main)
Water quality - Lead-210 - Test method using liquid scintillation counting (ISO 13163:2021)
SIST EN ISO 13163:2022

This document specifies a method for the measurement of 210Pb in all types of waters by liquid scintillation counting (LSC).
The method is applicable to test samples of supply/drinking water, rainwater, surface and ground water, as well as cooling water, industrial water, domestic, and industrial wastewater after proper sampling and handling, and test sample preparation. Filtration of the test sample is necessary. Lead‑210 activity concentration in the environment can vary and usually ranges from 2 mBq l-1 to 300 mBq l-1 [27][28].
Using currently available liquid scintillation counters, the limit of detection of this method for 210Pb is generally of the order of 20 mBq l-1 to 50 mBq l-1, which is lower than the WHO criteria for safe consumption of drinking water (100 mBq l−1).[4][6] These values can be achieved with a counting time between 180 min and 720 min for a sample volume from 0,5 l to 1,5 l. Higher activity concentrations can be measured by either diluting the sample or using smaller sample aliquots or both. The method presented in this document is not intended for the determination of an ultra-trace amount of 210Pb.
The range of application depends on the amount of dissolved material in the water and on the performance characteristics of the measurement equipment (background count rate and counting efficiency).
The method described in this document is applicable to an emergency situation.
The analysis of Pb adsorbed to suspended matter is not covered by this method.
It is the user’s responsibility to ensure the validity of this test method for the water samples tested.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 13160:2021(Main)
Water quality - Strontium 90 and strontium 89 - Test methods using liquid scintillation counting or proportional counting (ISO 13160:2021)
SIST EN ISO 13160:2021

This document specifies conditions for the determination of 90Sr and 89Sr activity concentration in samples of environmental water using liquid scintillation counting (LSC) or proportional counting (PC).
The method is applicable to test samples of drinking water, rainwater, surface and ground water, marine water, as well as cooling water, industrial water, domestic, and industrial wastewater after proper sampling and handling, and test sample preparation. Filtration of the test sample and a chemical separation are required to separate and purify strontium from a test portion of the sample.
The detection limit depends on the sample volume, the instrument used, the sample count time, the background count rate, the detection efficiency and the chemical yield. The method described in this document, using currently available LSC counters, has a detection limit of approximately 10 mBq l−1 and 2 mBq l−1 for 89Sr and 90Sr, respectively, which is lower than the WHO criteria for safe consumption of drinking water (100 Bq·l−1 for 89Sr and 10 Bq·l−1 for 90Sr)[3]. These values can be achieved with a counting time of 1 000 min for a sample volume of 2 l.
The methods described in this document are applicable in the event of an emergency situation. When fallout occurs following a nuclear accident, the contribution of 89Sr to the total amount of radioactive strontium is not negligible. This document provides test methods to determine the activity concentration of 90Sr in presence of 89Sr.
The analysis of 90Sr and 89Sr adsorbed to suspended matter is not covered by this method.
It is the user’s responsibility to ensure the validity of this test method selected for the water samples tested.

  • Standard
    51 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 10703:2021(Main)
Water quality - Gamma-ray emitting radionuclides - Test method using high resolution gamma-ray spectrometry (ISO 10703:2021)
SIST EN ISO 10703:2021

This document specifies a method for the physical pre-treatment and conditioning of water samples and the determination of the activity concentration of various radionuclides emitting gamma-rays with energies between 40 keV and 2 MeV, by gamma‑ray spectrometry according to the generic test method described in ISO 20042.
The method is applicable to test samples of drinking water, rainwater, surface and ground water as well as cooling water, industrial water, domestic and industrial wastewater after proper sampling, sample handling, and test sample preparation (filtration when necessary and taking into account the amount of dissolved material in the water). This method is only applicable to homogeneous samples or samples which are homogeneous via timely filtration.
The lowest limit that can be measured without concentration of the sample or by using only passive shield of the detection system is about 5·10-2 Bq/l for e.g. 137Cs.1 The upper limit of the activity corresponds to a dead time of 10 %. Higher dead times may be used but evidence of the accuracy of the dead-time correction is required.
Depending on different factors, such as the energy of the gamma-rays, the emission probability per nuclear disintegration, the size and geometry of the sample and the detector, the shielding, the counting time and other experimental parameters, the sample may require to be concentrated by evaporation if activities below 5·10-2 Bq/l need to be measured. However, volatile radionuclides (e.g. radon and radioiodine) can be lost during the source preparation.
This method is suitable for application in emergency situations.
1The sample geometry: 3l Marinelli beaker; detector: GE HP N relative efficiency 55 % ; counting time: 18h.

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 13162:2021(Main)
Water quality - Carbon 14 - Test method using liquid scintillation counting (ISO 13162:2021)
SIST EN ISO 13162:2021

This document specifies a method for the measurement of 14C activity concentration in all types of water samples by liquid scintillation counting (LSC) either directly on the test sample or following a chemical separation.
The method is applicable to test samples of supply/drinking water, rainwater, surface and ground water, marine water, as well as cooling water, industrial water, domestic, and industrial wastewater.
The detection limit depends on the sample volume, the instrument used, the sample counting time, the background count rate, the detection efficiency and the chemical recovery. The method described in this document, using currently available liquid scintillation counters and suitable technical conditions, has a detection limit as low as 1 Bq∙l−1, which is lower than the WHO criteria for safe consumption of drinking water (100 Bq·l-1). 14C activity concentrations can be measured up to 106 Bq∙l-1 without any sample dilution.
It is the user’s responsibility to ensure the validity of this test method for the water samples tested.

  • Standard
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 22017:2020(Main)
Water quality - Guidance for rapid radioactivity measurements in nuclear or radiological emergency situation (ISO 22017:2020)
SIST EN ISO 22017:2021

This document provides guidelines for testing laboratories wanting to use rapid test methods on water samples that may be contaminated following a nuclear or radiological emergency incident. In an emergency situation, consideration should be given to:
—     taking into account the specific context for the tests to be performed, e.g. a potentially high level of contamination;
—     using or adjusting, when possible, radioactivity test methods implemented during routine situations to obtain a result rapidly or, for tests not performed routinely, applying specific rapid test methods previously validated by the laboratory, e.g. for 89Sr determination;
—     preparing the test laboratory to measure a large number of potentially contaminated samples.
The aim of this document is to ensure decision makers have reliable results needed to take actions quickly and minimize the radiation dose to the public.
Measurements are performed in order to minimize the risk to the public by checking the quality of water supplies. For emergency situations, test results are often compared to operational intervention levels.
NOTE    Operational intervention levels (OILs) are derived from IAEA Safety Standards[8] or national authorities[9].
A key element of rapid analysis can be the use of routine methods but with a reduced turnaround time. The goal of these rapid measurements is often to check for unusual radioactivity levels in the test sample, to identify the radionuclides present and their activity concentration levels and to establish compliance of the water with intervention levels[10][11][12]. It should be noted that in such circumstances, validation parameters evaluated for routine use (e.g. reproducibility, precision, etc.) may not be applicable to the modified rapid method. However, due to the circumstances arising after an emergency, the modified method may still be fit-for-purpose although uncertainties associated with the test results need to be evaluated and may increase from routine analyses.
The first steps of the analytical approach are usually screening methods based on gross alpha and gross beta test methods (adaptation of ISO 10704 and ISO 11704) and gamma spectrometry (adaptation of ISO 20042, ISO 10703 and ISO 19581). Then, if required[13], test method standards for specific radionuclides (see Clause 2) are adapted and applied (for example, 90Sr measurement according to ISO 13160) as proposed in Annex A.
This document refers to published ISO documents. When appropriate, this document also refers to national standards or other publicly available documents.
Screening techniques that can be carried out directly in the field are not part of this document.

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 13161:2020(Main)
Water quality - Polonium 210 - Test method using alpha spectrometry (ISO 13161:2020)
SIST EN ISO 13161:2021

This document specifies a method for the measurement of 210Po in all types of waters by alpha spectrometry.
The method is applicable to test samples of supply/drinking water, rainwater, surface and ground water, marine water, as well as cooling water, industrial water, domestic, and industrial wastewater after proper sampling and handling, and test sample preparation. Filtration of the test sample may be required.
The detection limit depends on the sample volume, the instrument used, the counting time, the background count rate, the detection efficiency and the chemical yield. The method described in this document, using currently available alpha spectrometry apparatus, has a detection limit of approximately 5 mBq l−1, which is lower than the WHO criteria for safe consumption of drinking water (100 mBq l−1). This value can be achieved with a counting time of 24 h for a sample volume of 500 ml.
The method described in this document is also applicable in an emergency situation.
The analysis of 210Po adsorbed to suspended matter in the sample is not covered by this method.
If suspended material has to be removed or analysed, filtration using a 0,45 μm filter is recommended. The analysis of the insoluble fraction requires a mineralization step that is not covered by this document [13]. In this case, the measurement is made on the different phases obtained. The final activity is the sum of all the measured activity concentrations.
It is the user's responsibility to ensure the validity of this test method for the water samples tested.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 13164-3:2020(Main)
Water quality - Radon-222 - Part 3: Test method using emanometry (ISO 13164-3:2013)
SIST EN ISO 13164-3:2020

ISO 13164-3:2013 specifies a test method for the determination of radon-222 activity concentration in a sample of water following its transfer from the aqueous phase to the air phase by degassing and its detection. It gives recommendations for rapid measurements performed within less than 1 h.
The radon-222 activity concentrations, which can be measured by this test method utilizing currently available instruments, range from 0,1 Bq l−1 to several hundred thousand becquerels per litre for a 100 ml test sample.
This test method is used successfully with drinking water samples. The laboratory is responsible for ensuring the validity of this test method for water samples of untested matrices.
This test method can be applied on field sites or in the laboratory.
Annexes A and B give indications on the necessary counting conditions to meet the required sensitivity for drinking water monitoring

  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day