EN 12517:1998/A1:2002

SLOVENSKI STANDARD
01-maj-2003
Neporušitveno preskušanje zvarnih spojev - Radiografsko preskušanje zvarnih
spojev - Stopnje sprejemljivosti - Dopolnilo A1
Non-destructive testing of welds - Radiographic testing of welded joints - Acceptance
levels
Zerstörungsfreie Prüfung von Schweißverbindungen - Durchstrahlungsprüfung von
Schweißverbindungen - Zulässigkeitsgrenzen
Essais non destructifs des assemblages soudés - Contrôle par radiographie des
assemblages soudés - Niveaux d'acceptation
Ta slovenski standard je istoveten z: EN 12517:1998/A1:2002
ICS:
25.160.40 Varjeni spoji in vari Welded joints
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 12517:1998/A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2002
ICS 25.160.40
English version
Non-destructive testing of welds - Radiographic testing of
welded joints - Acceptance levels
Essais non destructifs des assemblages soudés - Contrôle Zerstörungsfreie Prüfung von Schweißverbindungen -
par radiographie des assemblages soudés - Niveaux Durchstrahlungsprüfung von Schweißverbindungen -
d'acceptation Zulässigkeitsgrenzen
This amendment A1 modifies the European Standard EN 12517:1998; it was approved by CEN on 23 August 2002.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references concerning such
national standards may be obtained on application to the Management Centre or to any CEN member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2002 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 12517:1998/A1:2002 E
worldwide for CEN national Members.

Contents
page
Foreword.3
General.4
1 Scope .4
2 Normative references .4
3 Radiographic technique .4
4 General.4
5 Acceptance levels.4
Annex A (informative)  Guide to the limitations of radiography.6
Annex ZA (informative) Clauses of this European Standard addressing essential requirements or other
provisions of EU directives.7
Foreword
This document (EN 12517:1998/A1:2002) has been prepared by Technical Committee CEN/TC 121 "Welding", the
secretariat of which is held by DS.
This European Standard shall be given the status of a national standard, either by publication of an identical text or
by endorsement, at the latest by April 2003 and conflicting national standards shall be withdrawn at the latest by
April 2003.
This document has been prepared under a mandate given to CEN by the European Commission and the European
Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative annex ZA, which is an integral part of this document.
Annex A is informative.
According to the CEN/CENELEC Internal Regulations, the national standards orga
...