EN 1402-5:2003
(Main)Unshaped refractory products - Part 5: Preparation and treatment of test pieces
Unshaped refractory products - Part 5: Preparation and treatment of test pieces
This standard specifies methods for the preparation and treatment (curing, drying and firing) of test pieces from unshaped refractory materials. The dimensions of the test pieces are specified. The methods are applicable to dense and insulating castables and to mouldable materials (plastics and ramming mixes) with the four types of chemical composition defined in ENV 1402-1.
Ungeformte feuerfeste Erzeugnisse - Teil 5: Herstellung und Behandlung von Probekörpern
Dieser Teil dieser Europäischen Norm legt Verfahren für die Herstellung und Behandlung (Lagern, Trocknen und Brennen) von Probekörpern aus ungeformten feuerfesten Erzeugnissen fest. Die Maße der Probekörper werden festgelegt.
Die Verfahren sind für dichte Feuerbetone, wärmedämmende Feuerbetone und Rammmassen mit den in prEN 1402 1 festgelegten vier Arten der chemischen Zusammensetzung anwendbar.
Produits réfractaires non façonnés - Partie 5: Préparation et traitement des éprouvettes
La présente partie de cette Norme européenne spécifie des méthodes de préparation et de traitement (cure, séchage et cuisson) d'éprouvettes de produits réfractaires non façonnés. Les dimensions des éprouvettes sont spécifiées.
Les méthodes s'appliquent aux bétons denses et isolants ainsi qu'aux matériaux moulables correspondant aux quatre types de compositions chimiques définies par Ie prEN 1402-l.
Neoblikovani ognjevzdržni izdelki - 5. del: Priprava vzorcev za preskus
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Neoblikovani ognjevzdržni izdelki - 5. del: Priprava vzorcev za preskusUngeformte feuerfeste Erzeugnisse - Teil 5: Herstellung und Behandlung von ProbekörpernProduits réfractaires non façonnés - Partie 5: Préparation et traitement des éprouvettesUnshaped refractory products - Part 5: Preparation and treatment of test pieces81.080Ognjevzdržni materialiRefractoriesICS:Ta slovenski standard je istoveten z:EN 1402-5:2003SIST EN 1402-5:2004en01-maj-2004SIST EN 1402-5:2004SLOVENSKI
STANDARDSIST ENV 1402-5:20001DGRPHãþD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 1402-5October 2003ICS 81.080Supersedes ENV 1402-5:1999English versionUnshaped refractory products - Part 5: Preparation andtreatment of test piecesProduits réfractaires non façonnés - Partie 5: Préparationet traitement des éprouvettesUngeformte feuerfeste Erzeugnisse - Teil 5: Herstellungund Behandlung von ProbekörpernThis European Standard was approved by CEN on 20 June 2003.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and UnitedKingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2003 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 1402-5:2003 ESIST EN 1402-5:2004
Length: 230 mm; width: 114 mm; thickness: 64 mm; Shape B:
Length: 230 mm; width: 64 mm; thickness: 54 mm; Shape C:
Length: 230 mm; width: 64 mm; thickness: 64 mm. The width of the test piece as tested shall correspond to the height during preparation. The vibration of the testpiece during preparation shall be recorded, and for shape C the compaction surface shall be marked for reference.The selection of test pieces for each type of material shall be as given in Table 1, except that for b
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.