EN 16232:2013/FprA1:2018

SLOVENSKI STANDARD
SIST EN 16232:2013/oprA1:2017
01-maj-2017
,]GHONL]DRWURNH*XJDOQLFH]DGRMHQþNH'RSROQLOR$
Child use and care articles - Infant swings
Artikel für Säuglinge und Kleinkinder - Babyschaukeln
Articles de puériculture - Balancelles suspendues pour enfant
Ta slovenski standard je istoveten z: EN 16232:2013/prA1
ICS:
97.190 Otroška oprema Equipment for children
SIST EN 16232:2013/oprA1:2017 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

SIST EN 16232:2013/oprA1:2017
SIST EN 16232:2013/oprA1:2017
DRAFT
EUROPEAN STANDARD
EN 16232:2013
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
March 2017
ICS 97.190
English Version
Child use and care articles - Infant swings
Articles de puériculture - Balancelles suspendues pour Artikel für Säuglinge und Kleinkinder - Babyschaukeln
enfant
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 252.

This draft amendment A1, if approved, will modify the European Standard EN 16232:2013. If this draft becomes an amendment,
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration.

This draft amendment was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 16232:2013/prA1:2017 E
worldwide for CEN national Members.

SIST EN 16232:2013/oprA1:2017
EN 16232:2013/prA1:2017 (E)
Contents Page
European foreword . 3
1 Modification to the European foreword . 4
2 Modification to Clause 1, Scope . 4
3 Modifications to Clause 2, Normative references . 4
4 Modification to 4.6, Test probes for finger entrapment . 4
5 Modification to Clause 6, Chemical hazards – migration of certain elements . 5
6 Modification to Clause 7, Thermal hazards . 8
7 Modification to 8.14.3, Test methods . 8
8 Modification to 8.3, Entrapment hazards . 9
9 Modification to 8.4.1.2.2, Test method for β and δ angles . 9
10 Modification to 8.4.1.2.3, Test method for γ angle . 9
11 Modification to 8.7, Hazards from entanglement in cords, ribbons and similar parts . 10
12 Modification to Clause 9, Product information . 11
13 Modification to 9.2.1, General requirements . 11
14 Modification to 9.2.2, Requirements for infant swings with electrical components . 11
15 Modification to 9.3, Purchase information . 11
16 Modification to 9.4.1, General . 11
17 Modification to 9.4.2, Warnings . 11
18 Modifications to Annex B (informative), A-deviation . 11
19 Addition of a new Annex C (normative), Warnings . 12
20 Modifications to the final Bibliography . 38

SIST EN 16232:2013/oprA1:2017
EN 16232:2013/prA1:2017 (E)
European foreword
This document (EN 16232:2013/prA1:2017) has been prepared by Technical Committee CEN/TC 252
“Child use and care articles”, the secretariat of which is held by AFNOR.
This document is currently submitted to the CEN Enquiry.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association.
SIST EN 16232:2013/oprA1:2017
EN 16232:2013/prA1:2017 (E)
1 Modification to the European foreword
nd
Replace the 2 paragraph with:
“This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by [DAV +6 months] and conflicting national standards
shall be withdrawn at the latest by [DAV + 12 months].".
2 Modification to Clause 1, Scope
Replace the whole Scope with the following one:
“This European Standard specifies safety requirements and test methods for chair mounted seats
intended to be positioned on an adult chair to raise the sitting position of a child able to sit unaided up
to an age of 36 months or a maximum weight of 15 kg.
This European Standard does not apply to cushions, pads and to products only aimed at restraining the
child on a chair without raising the child's sitting position.”.
3 Modifications to Clause 2, Normative references
Add the following references:
"EN 71-2:2011+A1:2014, Safety of toys — Part 2: Flammability";
"EN 71-10:2005, Safety of toys — Part 10: Organic chemical compounds — Sample preparation and
extraction";
"EN 71-11, Safety of toys — Part 11: Organic chemical compounds — Methods of analysis";
"EN 622-1, Fibreboards — Specifications — Part 1: General requirements";
"EN 717-1, Wood-based panels — Determination of formaldehyde release — Part 1: Formaldehyde
emission by the chamber method";
"EN ISO 14184-1, Textiles — Determination of formaldehyde — Part 1: Free and hydrolysed formaldehyde
(water extraction method) (ISO 14184-1)".
Replace "EN 71-3:1994" with "EN 71-3".
Delete:
"EN 1103, Textiles — Fabrics for apparel — Detailed procedure to determine the burning behaviour".
4 Modification to 4.6, Test probes for finger entrapment
Replace the whole subclause with the following one:
"
4.6 Test probes for finger entrapment
4.6.1 Finger probes with hemispherical end
Probes (see Figure 5) made from plastics or other hard, smooth material of diameters 7 mm and
( )
−01,
+01,
mm with a full hemispherical end that can be mounted on a force-measuring device.
( 0 )
Probe for mesh made from plastics or other hard, smooth material, with a full hemispherical end and
dimensions as stated in Figure 5, that can be mounted on a force-measuring device.
SIST EN 16232:2013/oprA1:2017
EN 16232:2013/prA1:2017 (E)
Dimensions in millimetres
a) b)
Key
Probe type 7 mm probe 12 mm probe Mesh probe
0 +01, 0
7 12 7
Diameter A
( ) ( ) ( )
−01, 0 −01,
5,6
Diameter B --- ---
( )
−01,
Radius RB half of diameter A half of diameter A half of diameter B
1 line scribed around circumference showing depth of penetration
Figure 5 — Test probes with hemispherical end
4.6.2 Shape assessment probe
Probe made from plastics or other hard, smooth material with the dimensions shown in Figure 6.

a) b)
Key
A front view
B top view
C side view
D 3D view
Figure 6 — Shape assessment probe
".
5 Modification to Clause 6, Chemical hazards – migration of certain elements
Replace Clause 6 with the following one:
SIST EN 16232:2013/oprA1:2017
EN 16232:2013/prA1:2017 (E)
"
6 Chemical hazards
6.1 General
If testing is required, a separate unconditioned sample shall be used for the tests in Clause 6.
6.2 Migration of certain elements (see A.2)
The migration of elements from materials on exterior surfaces shall not exceed the limits listed in
Table 1.
Table 1 — Limits for heavy metals migration
Element mg/kg
Aluminium 70 000
Antimony 560
Arsenic 47
Barium 18 750
Boron 15 000
Cadmium 17
Chromium (III) 460
Chromium (VI) 0,2
Cobalt 130
Copper 7 700
Lead 160
Manganese 15 000
Mercury 94
Nickel 930
Selenium 460
Strontium 56 000
Tin 180 000
Organic tin 12
Zinc 46 000
When testing is performed, the method described in EN 71-3 shall be used.
Materials on the back of the backrest and the surface under the sitting surface are excluded from these
requirements.
6.3 Formaldehyde (see A.2)
Accessible textile components shall not contain free and hydrolysed formaldehyde in excess of
30 mg/kg.
When testing is performed, the method described in EN ISO 14184-1 shall be used.
SIST EN 16232:2013/oprA1:2017
EN 16232:2013/prA1:2017 (E)
Resin-bonded wood components shall not release formaldehyde in excess of 0,124 mg/m (class E1
according to EN 622-1).
When testing is performed, the method described in EN 717-1 shall be used.
6.4 Colorants and primary aromatic amines (see A.2)
When tested in accordance with EN 71-10:2005, Annex A, if the colour fastness to sweat of accessible
textile components is lower than 3-4 on the grey scale as defined in EN 20105-A03, the part shall be
tested for colorants and primary aromatic amines with the methods described in EN 71-10 and EN 71-
11 and the limits in Table 2 and Table 3 shall be fulfilled.
Table 2 — Colourants limits
CoIour Index Generic Colour Index CAS Number Limit
Name (CIGN) Constitution
Number (CICN)
Disperse Blue 1 64500 2475–45–8 Action limit
Disperse Blue 3 61505 2475–46–9 Action limit
Disperse Blue 106 111935 12223-01-7 Action limit
Disperse Blue 124 111938 61951-51-7 Action limit
Disperse Yellow 3 11855 2832-40-8 Action limit
Disperse Orange 3 11855 730-40-5 Action limit
Disperse Orange 11132 12223-33-5 Action limit
37/76/59
13301-61-6
Disperse Red 1 11110 2872-52-8 Action limit
Solvent Yellow 1 11000 60-09-3 Action limit
Solvent Yellow 2 11020 60-11-7 Action limit
Solvent Yellow 3 11160 97-56-3 Action limit
Basic Red 9 42500 569-61-9 Action limit
Basic Violet 1 42535 8004-87-3 Action limit
Basic Violet 3 42555 548-62-9 Action limit
Acid Red 26 16150 3761–53–3 Action limit
Acid Violet 49 42640 1694–09–3 Action limit
SIST EN 16232:2013/oprA1:2017
EN 16232:2013/prA1:2017 (E)
Table 3 — Primary aromatic amines limits
Compound CAS number Limit
Benzidine 92–87–5 Action limit
2-Naphthylamine 91-59-8 Action limit
4-Chloroaniline 106–47–8 Action limit
3.3'-Dichlorobenzidine 91–94–1 Action limit
3.3'-Dimethoxybenzidine 119–90–4 Action limit
3.3'-Dimethylbenzidine 119–93–7 Action limit
o-Toluidine 95–53–4 Action limit
2-Methoxyaniline (o-Anisidine) 90-04-0 Action limit
Aniline 62–53–3 Action limit
".
6 Modification to Clause 7, Thermal hazards
Replace the whole clause with the following:
"
7 Thermal hazards (see A.3)
7.1 Requirement
When tested in accordance with 7.2, there shall be no surface flash and the rate of spread of flame shall
not exceed 50 mm/s.
A separate sample, conditioned according to 5.1, may be used for these tests.
7.2 Test method
To verify the surface flash effect apply the test flame defined in EN 71-2:2011+A1:2014, 5.5 for
(3 ± 0,5) s to the infant swing in different places likely to cause surface flash.
To verify rate of spread of flame apply the test flame defined in EN 71-2:2011+A1:2014, 5.4.".
7 Modification to 8.14.3, Test methods
Replace "Table 1" with "Table 4" in the table title and in the 2nd paragraph.
SIST EN 16232:2013/oprA1:2017
EN 16232:2013/prA1:2017 (E)
8 Modification to 8.3, Entrapment hazards
Replace the whole subclause with the following:
"
8.3 Entrapment hazards
8.3.1 Requirement
When tested in accordance with 8.3.2, there shall be no completely bounded openings, within the
protected volume, between 7 mm and 12 mm unless the depth is less than 10 mm or unless the shape
assessment probe (see 4.6) enters when tested in accordance with 8.3.2.
When tested in accordance with 8.3.2, there shall be no openings in mesh, within the protected volume,
that allow the test probe for mesh (see 4.6) to penetrate to the 7 mm diameter section.
The test shall be carried out with the product in any intended position of use.
This requirement does not apply to the restraint system.
8.3.2 Test method
Check whether the 7 mm probe (see 4.6), with an applied force of up to 30 N, enters 10 mm or more
into any accessible completely bounded opening in any possible orientation.
If the 7 mm probe enters 10 mm or more, then the 12 mm probe (see 4.6) shall also enter 10 mm or
more with an applied force of up to 5 N.
If the 7 mm probe enters with an applied force of up to 30 N but the 12 mm probe does not enter 10 mm
or
...