prEN ISO 9809-4
(Main)Gas cylinders - Design, construction and testing of refillable seamless steel gas cylinders and tubes - Part 4: Stainless steel cylinders with an R m value of less than 1 100 MPa (ISO/DIS 9809-4:2024)
Gas cylinders - Design, construction and testing of refillable seamless steel gas cylinders and tubes - Part 4: Stainless steel cylinders with an R m value of less than 1 100 MPa (ISO/DIS 9809-4:2024)
This document specifies the minimum requirements for the materials, design, construction and workmanship, manufacturing processes, examinations and testing at time of manufacture for refillable, seamless, stainless steel gas cylinders with water capacities up to and including 150 l.
It is applicable to cylinders for compressed, liquefied and dissolved gases with a maximum actual tensile strength, Rma, of less than 1 100 MPa.
NOTE If so desired, cylinders of water capacity between 150 l and 450 l can be manufactured to be in full conformance to this document.
Gasflaschen - Auslegung, Herstellung und Prüfung von wiederbefüllbaren nahtlosen Gasflaschen aus Stahl - Teil 4: Flaschen aus Edelstahl mit einem Rm-Wert von weniger als 1 100 MPa (ISO/DIS 9809‑4:2024)
Bouteilles à gaz - Conception, construction et essais des bouteilles à gaz et des tubes rechargeables en acier sans soudure - Partie 4: Bouteilles en acier inoxydable ayant une valeur de Rm inférieure à 1 100 MPa (ISO/DIS 9809-4:2024)
Le présent document spécifie les exigences minimales concernant le matériau, la conception, la construction et la mise en œuvre, les procédés de fabrication, les examens et les essais au moment de la fabrication des bouteilles à gaz rechargeables en acier sans soudure d’une contenance en eau inférieure ou égale à 150 l.
Il s’applique aux bouteilles pour les gaz comprimés, liquéfiés et dissous ayant une résistance à la traction réelle, Rma, maximale inférieure à 1 100 MPa.
NOTE Si cela est souhaité, les bouteilles d’une contenance en eau comprise entre 150 l et 450 l peuvent être fabriquées conformément au présent document.
Plinske jeklenke - Konstruiranje, izdelava in preskušanje ponovno polnljivih plinskih jeklenk in velikih jeklenk iz celega iz jekla - 4. del: Nerjavne jeklenke iz jekla z vrednostjo Rm, manjšo od 1100 MPa (ISO/DIS 9809-4:2024)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN ISO 9809-4:2024
01-julij-2024
Plinske jeklenke - Konstruiranje, izdelava in preskušanje ponovno polnljivih
plinskih jeklenk in velikih jeklenk iz celega iz jekla - 4. del: Nerjavne jeklenke iz
jekla z vrednostjo Rm, manjšo od 1100 MPa (ISO/DIS 9809-4:2024)
Gas cylinders - Design, construction and testing of refillable seamless steel gas cylinders
and tubes - Part 4: Stainless steel cylinders with an R m value of less than 1 100 MPa
(ISO/DIS 9809-4:2024)
Gasflaschen - Auslegung, Herstellung und Prüfung von wiederbefüllbaren nahtlosen
Gasflaschen aus Stahl - Teil 4: Flaschen aus Edelstahl mit einem Rm-Wert von weniger
als 1 100 MPa (ISO/DIS 9809-4:2024)
Bouteilles à gaz - Conception, construction et essais des bouteilles à gaz et des tubes
rechargeables en acier sans soudure - Partie 4: Bouteilles en acier inoxydable ayant une
valeur de Rm inférieure à 1 100 MPa (ISO/DIS 9809-4:2024)
Ta slovenski standard je istoveten z: prEN ISO 9809-4
ICS:
23.020.35 Plinske jeklenke Gas cylinders
oSIST prEN ISO 9809-4:2024 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 9809-4:2024
---------------------- Page: 2 ----------------------
oSIST prEN ISO 9809-4:2024
DRAFT
International
Standard
ISO/DIS 9809-4
ISO/TC 58/SC 3
Gas cylinders — Design,
Secretariat: BSI
construction and testing of
Voting begins on:
refillable seamless steel gas
2024-05-07
cylinders and tubes —
Voting terminates on:
2024-07-30
Part 4:
Stainless steel cylinders with an R
m
value of less than 1 100 MPa
Bouteilles à gaz — Conception, construction et essais des
bouteilles à gaz et des tubes rechargeables en acier sans
soudure —
Partie 4: Bouteilles en acier inoxydable ayant une valeur de Rm
inférieure à 1 100 MPa
ICS: 23.020.35
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Reference number
ISO/DIS 9809-4:2024(en)
© ISO 2024
---------------------- Page: 3 ----------------------
oSIST prEN ISO 9809-4:2024
DRAFT
ISO/DIS 9809-4:2024(en)
International
Standard
ISO/DIS 9809-4
ISO/TC 58/SC 3
Gas cylinders — Design,
Secretariat: BSI
construction and testing of
Voting begins on:
refillable seamless steel gas
cylinders and tubes —
Voting terminates on:
Part 4:
Stainless steel cylinders with an R
m
value of less than 1 100 MPa
Bouteilles à gaz — Conception, construction et essais des
bouteilles à gaz et des tubes rechargeables en acier sans
soudure —
Partie 4: Bouteilles en acier inoxydable ayant une valeur de Rm
inférieure à 1 100 MPa
ICS: 23.020.35
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
COPYRIGHT PROTECTED DOCUMENT
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
© ISO 2024
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
BE CONSIDERED IN THE LIGHT OF THEIR
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
or ISO’s member body in the country of the requester.
NATIONAL REGULATIONS.
ISO copyright office
RECIPIENTS OF THIS DRAFT ARE INVITED
CP 401 • Ch. de Blandonnet 8
TO SUBMIT, WITH THEIR COMMENTS,
CH-1214 Vernier, Geneva
NOTIFICATION OF ANY RELEVANT PATENT
Phone: +41 22 749 01 11
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland Reference number
ISO/DIS 9809-4:2024(en)
© ISO 2024
© ISO 2024 – All rights reserved
ii
---------------------- Page: 4 ----------------------
oSIST prEN ISO 9809-4:2024
ISO/DIS 9809-4:2024(en)
Contents Page
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.