EN ISO 7089:2000

SLOVENSKI STANDARD
01-julij-2002
Okrogle ravne podložke - Normalne vrste - Razred izdelave A (ISO 7089:2000)
Plain washers - Normal series - Product grade A (ISO 7089:2000)
Flache Scheiben - Normale Reihe - Produktklasse A (ISO 7089:2000)
Rondelles plates - Série normale - Grade A (ISO 7089:2000)
Ta slovenski standard je istoveten z: EN ISO 7089:2000
ICS:
21.060.30 Podložke, varovalni elementi Washers, locking elements
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

INTERNATIONAL ISO
STANDARD 7089
Second edition
2000-06-01
Plain washers — Normal series — Product
grade A
Rondelles plates — Série normale — Grade A
Reference number
ISO 7089:2000(E)
©
ISO 2000
ISO 7089:2000(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 � CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 734 10 79
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
ii © ISO 2000 – All rights reserved

ISO 7089:2000(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 7089 was prepared by Technical Committee ISO/TC 2, Fasteners.
This second edition cancels and replaces the first edition (ISO 7089:1983), which has been technically revised.
INTERNATIONAL STANDARD ISO 7089:2000(E)
Plain washers — Normal series — Product grade A
1 Scope
This International Standard specifies the characteristics of normal-series, product-grade-A plain washers in the
200 HV and 300 HV hardness classes and of nominal sizes (nominal thread diameters) ranging from 1,6 mm to
64 mm inclusive.
Washers of hardness class 200 HV are suitable for
� hexagon bolts and screws of product grades A and B in property classes up to and including 8.8;
� hexagon nuts of product grades A and B in property classes up to and including 8;
� hexagon bolts, screws and nuts of stainless steel of similar chemical composition;
� case-hardened thread rolling screws.
Washers of hardness class 300 HV are suitable for
� hexagon bolts and screws of product grades A and B in property classes up to and including 10.9;
� hexagon nuts of product grades A and B in property classes up to and including 10.
If dimensions other than those listed in this International Standard are required, they should be selected from those
given in ISO 887.
When soft material pieces are clamped, or large c
...