ASTM C1127/C1127M-15
(Guide)Standard Guide for Use of High Solids Content, Cold Liquid-Applied Elastomeric Waterproofing Membrane with an Integral Wearing Surface
Standard Guide for Use of High Solids Content, Cold Liquid-Applied Elastomeric Waterproofing Membrane with an Integral Wearing Surface
SIGNIFICANCE AND USE
4.1 This guide is divided into two sections which provide design and specification guidelines for the use of a cold liquid-applied elastomeric membrane with integral wearing surface for waterproofing building decks in building areas to be occupied by personnel, vehicles, or equipment.
4.2 The intent of Sections 5 – 11, Design Considerations, is to provide information and design guidelines where a waterproofing membrane with integral wearing surface is to be used. The intent of the remaining sections is to provide minimum guide specifications for the use of the purchaser and the seller in contract documents.
4.3 Where the state of the art is such that criteria for a particular condition is not as yet firmly established or has numerous variables that require consideration, reference is made to the applicable portion of Sections 5 – 11 that covers the particular area of concern. Section 16 describes the repair, rehabilitation, and replacement of the membrane.
SCOPE
1.1 This guide describes the design and installation of cold liquid-applied elastomeric waterproofing membrane systems that have an integral wearing surface. The cold liquid-applied elastomeric waterproofing membrane (membrane) to which this guide refers is specified in Specification C957.
1.2 Concrete Slab-on-Grade—Waterproofing the upper surface of a concrete slab on grade presents special problems due to the possibility of negative hydrostatic pressure causing loss of bond to the substrate. Consideration of these problems is beyond the scope of this guide. Consult the membrane manufacturer for recommendations when this situation exists.
1.3 The committee having jurisdiction for this guide is not aware of any similar ISO standard.
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements see 15.4.
General Information
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: C1127/C1127M − 15
Standard Guide for
Use of High Solids Content, Cold Liquid-Applied
Elastomeric Waterproofing Membrane with an Integral
1
Wearing Surface
This standard is issued under the fixed designation C1127/C1127M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope C150 Specification for Portland Cement
C330 Specification for Lightweight Aggregates for Struc-
1.1 This guide describes the design and installation of cold
tural Concrete
liquid-applied elastomeric waterproofing membrane systems
C332 Specification for Lightweight Aggregates for Insulat-
that have an integral wearing surface. The cold liquid-applied
ing Concrete
elastomeric waterproofing membrane (membrane) to which
C717 Terminology of Building Seals and Sealants
this guide refers is specified in Specification C957.
C755 Practice for Selection of Water Vapor Retarders for
1.2 Concrete Slab-on-Grade—Waterproofing the upper sur-
Thermal Insulation
face of a concrete slab on grade presents special problems due
C920 Specification for Elastomeric Joint Sealants
to the possibility of negative hydrostatic pressure causing loss
C957 Specification for High-Solids Content, Cold Liquid-
of bond to the substrate. Consideration of these problems is
Applied Elastomeric Waterproofing Membrane With Inte-
beyond the scope of this guide. Consult the membrane manu-
gral Wearing Surface
facturer for recommendations when this situation exists.
C962 Standards Guide for Use of Elastomeric Joint Sealants
3
1.3 The committee having jurisdiction for this guide is not (Withdrawn 1992)
C1193 Guide for Use of Joint Sealants
aware of any similar ISO standard.
D653 Terminology Relating to Soil, Rock, and Contained
1.4 The values stated in either SI units or inch-pound units
Fluids
are to be regarded separately as standard. The values stated in
D1079 Terminology Relating to Roofing and Waterproofing
each system may not be exact equivalents; therefore, each
D1752 Specification for Preformed Sponge Rubber Cork
system shall be used independently of the other. Combining
and Recycled PVC Expansion Joint Fillers for Concrete
values from the two systems may result in non-conformance
Paving and Structural Construction
with the standard.
D2628 Specification for Preformed Polychloroprene Elasto-
1.5 This standard does not purport to address all of the
meric Joint Seals for Concrete Pavements
safety concerns, if any, associated with its use. It is the
2.2 U.S. Department of Commerce Standard:
responsibility of the user of this standard to establish appro-
Product Standard PS 1-74 Construction and Industrial Ply-
priate safety and health practices and determine the applica-
4
wood
bility of regulatory limitations prior to use. For specific hazard
2.3 American Concrete Institute (ACI) Standard:
statements see 15.4.
301-84 (1985) Specification for Structural Concrete for
5
Buildings
2. Referenced Documents
2
2.4 Steel Structures Painting Council (SSPC) Standards:
2.1 ASTM Standards:
Steel Structures Painting Manual, Systems and Specifica-
C33 Specification for Concrete Aggregates
tions:
6
Specification SSPC SP-2 Wire Brush Cleaning
1
This guide is under the jurisdiction of ASTM Committee D08 on Roofing and
Waterproofing and is the direct responsibility of Subcommittee D08.25 on Liquid
Applied Polymeric Materials Used for Roofing and Waterproofing Membranes that
3
are Directly Exposed to the Weather. The last approved version of this historical standard is referenced on
Current edition approved Jan. 1, 2015. Published February 2015. Originally www.astm.org.
4
approved in 1989. Last previous edition approved in 2009 as C1127 – 01 (2009). Available from National Institute of Standards and Technology (NIST), 100
DOI: 10.1520/C1127_C1127M-15. Bureau Dr., Stop 1070, Gaithersburg, MD 20899-1070, http://www.nist.gov.
2 5
For referenced ASTM standards, visit the ASTM website, www.astm.org, or Available from American Concrete Institute (ACI), P.O. Box 9094, Farmington
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Hills, MI 48333-9094, http://www.concrete.org.
6
Standards volume information, refer to the standard’s Document Summary page on Available from Society for Protective Coatings (SSPC), 40 24th St., 6th Floor,
the ASTM website. Pittsburgh, PA 15222-4656, http://www.sspc.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C1127/C1127M − 15
6
Specification SSPC SP-6 Commercial Blast Cleaning surface for wate
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: C1127 − 01 (Reapproved 2009) C1127/C1127M − 15
Standard Guide for
Use of High Solids Content, Cold Liquid-Applied
Elastomeric Waterproofing Membrane with an Integral
1
Wearing Surface
This standard is issued under the fixed designation C1127;C1127/C1127M; the number immediately following the designation indicates
the year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This guide describes the design and installation of cold liquid-applied elastomeric waterproofing membrane systems that
have an integral wearing surface. The cold liquid-applied elastomeric waterproofing membrane (membrane) to which this guide
refers is specified in Specification C957.
1.2 Concrete Slab-on-Grade—Waterproofing the upper surface of a concrete slab on grade presents special problems due to the
possibility of negative hydrostatic pressure causing loss of bond to the substrate. Consideration of these problems is beyond the
scope of this guide. Consult the membrane manufacturer for recommendations when this situation exists.
1.3 The committee having jurisdiction for this guide is not aware of any similar ISO standard.
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as the standard. The values given in
parentheses are for information only.stated in each system may not be exact equivalents; therefore, each system shall be used
independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use. For specific hazard statements see Note in 15.4.
2. Referenced Documents
2
2.1 ASTM Standards:
C33 Specification for Concrete Aggregates
C150 Specification for Portland Cement
C330 Specification for Lightweight Aggregates for Structural Concrete
C332 Specification for Lightweight Aggregates for Insulating Concrete
C717 Terminology of Building Seals and Sealants
C755 Practice for Selection of Water Vapor Retarders for Thermal Insulation
C920 Specification for Elastomeric Joint Sealants
C957 Specification for High-Solids Content, Cold Liquid-Applied Elastomeric Waterproofing Membrane With Integral Wearing
Surface
3
C962 Standards Guide for Use of Elastomeric Joint Sealants (Withdrawn 1992)
C1193 Guide for Use of Joint Sealants
D653 Terminology Relating to Soil, Rock, and Contained Fluids
D1079 Terminology Relating to Roofing and Waterproofing
D1752 Specification for Preformed Sponge Rubber Cork and Recycled PVC Expansion Joint Fillers for Concrete Paving and
Structural Construction
D2628 Specification for Preformed Polychloroprene Elastomeric Joint Seals for Concrete Pavements
1
This guide is under the jurisdiction of ASTM Committee D08 on Roofing and Waterproofing and is the direct responsibility of Subcommittee D08.25 on Liquid Applied
Polymeric Materials Used for Roofing and Waterproofing Membranes that are Directly Exposed to the Weather.
Current edition approved Jan. 1, 2009Jan. 1, 2015. Published January 2009February 2015. Originally approved in 1989. Last previous edition approved in 20012009 as
C1127 – 01.C1127 – 01 (2009). DOI: 10.1520/C1127-01R09.10.1520/C1127_C1127M-15.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
The last approved version of this historical standard is referenced on www.astm.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C1127/C1127M − 15
2.2 U.S. Department of Commerce Standard:
4
Product Standard PS 1-74 Construction and Industrial Plywood
2.3 American Concrete Institute (ACI) Standard:
5
301-84 (1985) Specification for Structural Concrete for Buildings
2.4 Steel Structures Painting Council (SSPC) Standards:
Steel Structures Painting Manual, Systems and Specifications:
6
Specification SSPC SP-2 Wire Brush Cleaning
6
Specification SSPC SP-6 Commercial Blast Cleaning
2.5 American Plywood Association (AP
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.