iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM C1522-05(2013)

(Test Method)

Standard Test Method for Extensibility After Heat Aging of Cold Liquid-Applied Elastomeric Waterproofing Membranes

Standard Test Method for Extensibility After Heat Aging of Cold Liquid-Applied Elastomeric Waterproofing Membranes

SIGNIFICANCE AND USE
6.1 This test method is used to determine a membrane's ability to bridge a crack that forms after the membrane has been applied and allowed to cure.
SCOPE
1.1 This test method describes a laboratory procedure for determining extensibility for one- or two-component cold liquid-applied elastomeric waterproofing membranes.  
1.2 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only.  
1.3 The committee with jurisdiction over this standard is not aware of any comparable standards published by other organizations.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
30-Apr-2013
ICS
83.060 - Rubber
Technical Committee
D08 - Roofing and Waterproofing
Drafting Committee
D08.22 - Waterproofing and Dampproofing Systems
Current Stage
Ref Project

Buy Standard

ASTM C1522-05(2013) - Standard Test Method for Extensibility After Heat Aging of Cold Liquid-Applied Elastomeric Waterproofing MembranesASTM C1522-05(2013) - Standard Test Method for Extensibility After Heat Aging of Cold Liquid-Applied Elastomeric Waterproofing Membranes
PreviousNext
Standard
ASTM C1522-05(2013) - Standard Test Method for Extensibility After Heat Aging of Cold Liquid-Applied Elastomeric Waterproofing Membranes
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:C1522 −05 (Reapproved 2013)
Standard Test Method for
Extensibility After Heat Aging of Cold Liquid-Applied
Elastomeric Waterproofing Membranes
This standard is issued under the fixed designation C1522; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 5. Summary of Test Method
1.1 This test method describes a laboratory procedure for 5.1 Thistestmethodconsistsofpreparingthreesamples,for
determining extensibility for one- or two-component cold eachmembranetobetested,andextendingafteraging14days
liquid-applied elastomeric waterproofing membranes. at 70 6 2°C (158 6 3.6°F).
1.2 The values stated in SI units are to be regarded as the
6. Significance and Use
standard. The values in parentheses are for information only.
6.1 This test method is used to determine a membrane’s
1.3 Thecommitteewithjurisdictionoverthisstandardisnot
ability to bridge a crack that forms after the membrane has
aware of any comparable standards published by other orga-
been applied and allowed to cure.
nizations.
7. Apparatus
1.4 This standard does not purport to address all of the
7.1 Forced Draft Oven, controlled to 70 6 2°C (158 6
safety concerns, if any, associated with its use. It is the
responsibility of the user of this standard to establish appro- 3.6°F).
priate safety and health practices and determine the applica-
7.2 Three Mortar Test Blocks, dimensions 12 × 76 × 152
bility of regulatory limitations prior to use.
1 1
mm ( ⁄2×3×6 in.) nominal with 6 mm ( ⁄4 in.) deep notch cut
across the width (see Fig. 1).
2. Referenced Documents
7.3 Masking Tape.
2.1 ASTM Standards:
7.4 Sand.
C717Terminology of Building Seals and Sealants
C1250TestMethodforNonvolatileContentofColdLiquid-
7.5 Wood Board, Steel Wedge, Hammer, and Wood Blades.
Applied Elastomeric Waterproofing Membranes
7.6 Testing Machine,withtensiongripscapableofpullingat
C1375Guide for Substrates Used in Testing Building Seals
a rate of separation of 12.7 mm (0.5 in.)/min.
and Sealants
7.7 Vernier Calipers.
3. Terminology
8. Conditioning/Mixing
3.1 Definitions—Refer to Terminology C717 for definitions
8.1 Unless otherwise specified by those authorizing the test,
of terms used in this standard.
standardconditionsare23 61°C(73.4 61.8°F)and50 65%
relative humidity.
4. Comparison to Other Standards
8.2 Store all membrane materials to be tested in an un-
4.1 Thecommitteewithjurisdictionoverthisstandardisnot
openedcontaineratstandardconditionsforatleast24hbefore
aware of any comparable standards published by other orga-
any test specimens are prepared.
nizations.
8.3 Follow the manufacturer’s instructions for mixing and
preparing membrane materials for testing. Thoroughly stir
ThistestmethodisunderthejurisdictionofASTMCommitteeD08onRoofing
one-component materials before using. Mix two-component
and Waterproofing and is the direct responsibility of Subcommittee D08.22 on
compounds in the ratio recommended by the manufacturer. If
Waterproofing and Dampproofing Systems.
required by the manufacturer, mix each component prior to the
Current edition approved May 1, 2013. Published May 2013. Originally
approved in 2002. Last previous edition approved in 2005 as C1522–05. DOI: final mix.
10.1520/C1522-05R13.
For referenced ASTM standards, visit the ASTM website, www.astm.org, or 9. Procedure
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
9.1 Prepare three test specimens for each membrane to be
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. tested as follows:
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
C1522−05 (2013)
FIG. 1Test Block for Testing Extensibility After Heat Aging
9.1.1 Cut each of the three mortar slabs crosswise in the 9.1.5 Forself-levelingmembranematerials,laytheslabson
centerofthe152mm(6in.)lengthtoadepthof6mm( ⁄4in.),
a bed of sand and level them.
as shown in Fig. 1.
NOTE 2—For self-leveling membranes, apply 50 mm (1 in.) wide
NOTE 1—Mortar substrates must
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM C957/C957M-17(2024)(Specification)
Standard Specification for High-Solids Content, Cold Liquid-Applied Elastomeric Waterproofing Membrane with Integral Wearing Surface

ABSTRACT
This specification describes the required properties and test methods for high-solids content, cold liquid-applied elastomeric membrane with integral wearing surface for waterproofing building decks not subject to hydrostatic pressure. This specification does not include specific requirements for skid resistance or fire retardance, although both may be important in specific uses. The properties to which the materials will be tested upon for conformance are as follows: weight loss of base coat; low temperature crack bridging; adhesion-in-peel to cement mortar and plywood substrates after water immersion; chemical resistance after water, ethylene glycol, and mineral spirits exposure; weathering resistance, recovery from elongation, tensile retention, and elongation retention; abrasion resistance; and stability.
SCOPE
1.1 This specification describes the required properties and test methods for a cold liquid-applied elastomeric membrane for waterproofing building decks not subject to hydrostatic pressure. The specification applies only to a membrane system that has an integral wearing surface. This specification does not include specific requirements for skid resistance or fire retardance, although both may be important in specific uses.  
1.2 The type of membrane system described in this specification is used for pedestrian and vehicular traffic and in high-abrasion applications. The membrane may be single or multi-component, and may consist of one or more coats (for example base coat, top coat, etc.). The coat(s) may be built to the desired thickness in one or more applications. One coat (base coat) provides the primary waterproofing function and normally comprises the major amount of organic material in the membrane. The function of the top coat(s) is to resist wear and weather. Aggregate may be used as a component of the membrane system, as all or part of a course, to increase wear and skid resistance.  
1.3 The committee with jurisdiction over this standard is not aware of any comparable standards published by other organizations.  
1.4 Test methods in this specification require a minimum 0.5 mm [0.020 in.] base coat dry film thickness. Actual thickness required for a particular application and the use of aggregate in top coats shall be established by the membrane manufacturer.  
1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.6 The following safety hazards caveat pertains only to the test method portion, Section 5, of this specification: This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM C898/C898M-09(2024)(Guide)
Standard Guide for Use of High Solids Content, Cold Liquid-Applied Elastomeric Waterproofing Membrane with Separate Wearing Course

SIGNIFICANCE AND USE
4.1 Designers and installers of waterproofing systems may consult this guide for a discussion of important elements of the use of cold liquid-applied waterproofing membranes and associated elements of construction. This guide is not intended to serve as a specification for waterproofing installation.  
4.2 Long-term performance of waterproofing with a separate wearing course is important because of the substantial difficulty in determining the location of leakage and in removing overlying materials to make repairs.  
4.3 Refer to Guide C1471/C1471M for application on below grade walls and vertical surfaces.
SCOPE
1.1 This guide describes the use of a high solids content, cold liquid-applied elastomeric waterproofing membrane that meets the criteria in Specification C836/C836M, in a waterproofing system subject to hydrostatic pressure for building decks over occupied space where the membrane is covered with a separate protective wearing course.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    14 pages
    English language
    sale 15% off
ASTM
ASTM D4811/D4811M-16(2023)(Specification)
Standard Specification for Nonvulcanized (Uncured) Rubber Sheet Used as Roof Flashing

ABSTRACT
This specification covers nonvulcanized (uncured) rubber sheet made of ethylene-propylene-diene terpolymer (EPDM) or polychloroprene (CR) intended for use as watertight roof flashing exposed to the weather. In-place roof system design criteria such as fire resistance, field seaming strength, material compatibility, and uplift resistance, among others, are beyond the scope of this specification. The flashing material shall be formulated from the appropriate polymer type and other compounding ingredients, and shall be capable of being bonded to itself, to the roofing membrane, and to substrate for making watertight field splices and repairs. Property requirements for flashing before vulcanization include thickness, Green strength modulus, ultimate elongation, shelf stability, vulcanizability, tensile strength and set, dimensional stability, and weatherability. Consequently, the property requirements for flashing after vulcanization includes tensile strength and set, elongation, tear resistance, brittle point, ozone resistance, air oven heat aging, water absorption and weight change, linear dimension change, and weatherability.
SCOPE
1.1 This specification covers nonvulcanized (uncured) rubber sheet made of EPDM (ethylene-propylene-diene terpolymer) or CR (polychloroprene) intended for use as watertight roof flashing exposed to the weather.  
1.2 The tests and property limits used to characterize these flashing materials are specific for each classification and are minimum values to make the product fit for its intended purpose.  
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.4 In-place roof system design criteria, such as fire resistance, field seaming strength, material compatibility, and uplift resistance, among others, are beyond the scope of this specification.  
1.5 The following precautionary caveat pertains to the test methods portion only, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM C1522-05(2021)(Test Method)
Standard Test Method for Extensibility After Heat Aging of Cold Liquid-Applied Elastomeric Waterproofing Membranes

SIGNIFICANCE AND USE
6.1 This test method is used to determine a membrane's ability to bridge a crack that forms after the membrane has been applied and allowed to cure.
SCOPE
1.1 This test method describes a laboratory procedure for determining extensibility for one- or two-component cold liquid-applied elastomeric waterproofing membranes.  
1.2 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only.  
1.3 The committee with jurisdiction over this standard is not aware of any comparable standards published by other organizations.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D4637/D4637M-15(2021)e1(Specification)
Standard Specification for EPDM Sheet Used in Single-Ply Roof Membrane

SCOPE
1.1 This specification covers flexible sheet made from ethylene-propylene-diene terpolymer (EPDM) intended for use in single-ply roofing membranes exposed to the weather. The tests and property limits used to characterize the sheet are values to ensure minimum quality for the intended use. The sheet may be non-reinforced, fabric- or scrim-reinforced, or fabric-backed vulcanized rubber sheet.  
1.2 In-place roof system design criteria, such as fire resistance, field seaming strength, material compatibility, and uplift resistance, among others, are factors that must be considered but are beyond the scope of this specification.  
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM C957/C957M-17(2024)(Specification)
Standard Specification for High-Solids Content, Cold Liquid-Applied Elastomeric Waterproofing Membrane with Integral Wearing Surface

ABSTRACT
This specification describes the required properties and test methods for high-solids content, cold liquid-applied elastomeric membrane with integral wearing surface for waterproofing building decks not subject to hydrostatic pressure. This specification does not include specific requirements for skid resistance or fire retardance, although both may be important in specific uses. The properties to which the materials will be tested upon for conformance are as follows: weight loss of base coat; low temperature crack bridging; adhesion-in-peel to cement mortar and plywood substrates after water immersion; chemical resistance after water, ethylene glycol, and mineral spirits exposure; weathering resistance, recovery from elongation, tensile retention, and elongation retention; abrasion resistance; and stability.
SCOPE
1.1 This specification describes the required properties and test methods for a cold liquid-applied elastomeric membrane for waterproofing building decks not subject to hydrostatic pressure. The specification applies only to a membrane system that has an integral wearing surface. This specification does not include specific requirements for skid resistance or fire retardance, although both may be important in specific uses.  
1.2 The type of membrane system described in this specification is used for pedestrian and vehicular traffic and in high-abrasion applications. The membrane may be single or multi-component, and may consist of one or more coats (for example base coat, top coat, etc.). The coat(s) may be built to the desired thickness in one or more applications. One coat (base coat) provides the primary waterproofing function and normally comprises the major amount of organic material in the membrane. The function of the top coat(s) is to resist wear and weather. Aggregate may be used as a component of the membrane system, as all or part of a course, to increase wear and skid resistance.  
1.3 The committee with jurisdiction over this standard is not aware of any comparable standards published by other organizations.  
1.4 Test methods in this specification require a minimum 0.5 mm [0.020 in.] base coat dry film thickness. Actual thickness required for a particular application and the use of aggregate in top coats shall be established by the membrane manufacturer.  
1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.6 The following safety hazards caveat pertains only to the test method portion, Section 5, of this specification: This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM C898/C898M-09(2024)(Guide)
Standard Guide for Use of High Solids Content, Cold Liquid-Applied Elastomeric Waterproofing Membrane with Separate Wearing Course

SIGNIFICANCE AND USE
4.1 Designers and installers of waterproofing systems may consult this guide for a discussion of important elements of the use of cold liquid-applied waterproofing membranes and associated elements of construction. This guide is not intended to serve as a specification for waterproofing installation.  
4.2 Long-term performance of waterproofing with a separate wearing course is important because of the substantial difficulty in determining the location of leakage and in removing overlying materials to make repairs.  
4.3 Refer to Guide C1471/C1471M for application on below grade walls and vertical surfaces.
SCOPE
1.1 This guide describes the use of a high solids content, cold liquid-applied elastomeric waterproofing membrane that meets the criteria in Specification C836/C836M, in a waterproofing system subject to hydrostatic pressure for building decks over occupied space where the membrane is covered with a separate protective wearing course.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    14 pages
    English language
    sale 15% off
ASTM
ASTM F3258-23(Specification)
Standard Specification for Protectors for Rubber Insulating Gloves Meeting Specific Performance Requirements

SCOPE
1.1 This specification establishes specifications and test requirements for protectors to be worn over electrical workers’ rubber insulating gloves.  
1.2 It is intended that the protectors specified herein fit snugly over rubber insulating gloves specified in Specification D120 without causing mechanical damage to the rubber insulating glove. Cinching at the wrist is allowed.  
1.3 This specification covers the use of a material or combination of materials which do not compromise the integrity of the rubber insulating glove.  
1.4 Specification F696 was used to establish minimums for this specification.  
1.5 Protectors meeting this specification do not provide any electrical shock protection if used on their own.  
1.6 This specification specifies the response of protectors to electric arc, puncture and cut under controlled conditions.  
1.6.1 Field conditions will not directly correlate to testing methods.  
1.7 The values stated in SI units are to be regarded as the standard except as noted. See IEEE/ASTM SI-10.  
1.8 The following safety hazards caveat pertains only to the test method portion, Sections 6 and 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM D5508-23(Test Method)
Standard Test Method for Determination of Residual Acrylonitrile Monomer in Styrene-Acrylonitrile Copolymer Resins and Nitrile-Butadiene Rubber by Headspace-Capillary Gas Chromatography (HS-CGC)

SIGNIFICANCE AND USE
4.1 A measurement of the residual acrylonitrile in nitrile rubbers (NBR), styrene-acrylonitrile copolymers or ABS terpolymers will determine the polymer's suitability for various applications.  
4.2 Under optimum conditions, the minimum level of detection of RAN in NBR, SAN, or ABS terpolymers is approximately 50 ppb.
SCOPE
1.1 This test method covers the determination of the residual acrylonitrile (RAN) content in nitrile-butadiene rubbers (NBR), styrene-acrylonitrile (SAN) copolymers, and rubber-modified acrylonitrile-butadiene-styrene (ABS) resins.  
1.2 Any components that can generate acrylonitrile in the headspace procedure will constitute an interference. The presence of 3-hydroxypropionitrile in latices limits this procedure to dry rubbers and resins.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in 6.3 and 6.4.
Note 1: There is no known ISO equivalent to this standard.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM D8491-23(Test Method)
Standard Test Method for Recovered Carbon Black—Rheological Non-Linearity of a Rubber Compound by Fourier Transform Rheology

SIGNIFICANCE AND USE
3.1 This test method provides a measure of rheological non-linearity for filled rubber compounds under oscillatory shear conditions: the normalized 3rd harmonic of the torque I3/1.  
3.2 Rheological linearity means that the modulus is a function of frequency only. The shear modulus dependency on both frequency and amplitude of a dynamic deformation is a non-linear, rheological effect. Filled rubbers show a strain dependency of the modulus known as Payne effect. A test method for evaluating the Payne effect can be found in Test Method D8059.  
3.3 One of the main contributions to the Payne effect is the so-called polymer-filler interaction in the range of mid amplitude oscillation shear, MAOS. The MAOS amplitude range is defined as the range where I3/1 is already measurable and increases according to a scaling law, for example, I3/1 ~ γ2. It has been shown that FT rheological measurements are very sensitive to changes in this interaction, and that it is possible to quantify the influence of the filler type and content on the nonlinearity. Interactions between the polymer and particle surface and between the filler particles create a network structure in the compound that not only increases the elasticity of the system but also introduces nonlinear contributions to the stress response.3
SCOPE
1.1 This test method provides a measure of rheological non-linearity of a rubber compound filled with rCB to assess its reinforcement capabilities. This test method requires the use of a sealed cavity rotorless oscillating shear rheometer for the measurement of the torque with increasing sinusoidal strain applied to an uncured rubber compound containing significant amounts of colloidal fillers, such as recovered carbon black, alone or as blend with virgin carbon black.  
1.2 Units—The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
  • Standard
    2 pages
    English language
    sale 15% off