Standard Test Method for Flame Height, Time of Burning, and Loss of Mass of Rigid Thermoset Cellular Plastics in a Vertical Position

SIGNIFICANCE AND USE
5.1 Tests made on rigid cellular materials in accordance with the conditions described by this test method can be of considerable value in comparing their burning characteristics.  
5.2 This test method has been applied to flexible cellular materials and other plastics, but no detailed studies have been conducted to determine its general applicability to these materials.  
5.3 In this procedure, the specimens are subjected to one or more specific sets of laboratory test conditions. If different test conditions are substituted or the end-use conditions are changed, it is not always possible by or from this test to predict changes in the fire-test-response characteristics measured. The results are therefore valid only for the fire-test-exposure conditions described in this procedure.
SCOPE
1.1 This is a fire-test-response standard. This test method covers a small-scale laboratory screening procedure for comparing relative extent and time of burning and loss of mass of rigid thermoset cellular plastics. This test method is to be used solely to establish relative burning characteristics.  
1.1.1 This test method shall not be used for materials that drip or melt under the test conditions.  
1.2 During the course of combustion, gases or vapors, or both, are evolved which are potentially hazardous to personnel. Adequate precautions shall be taken to protect the operator.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. A specific precautionary statement is given in 1.2.  
1.4 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of materials, products, or assemblies under actual fire conditions.  
1.5 Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests.
Note 1: There is no known ISO equivalent to this standard.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

Status
Historical
Publication Date
31-Jul-2019
Technical Committee
Drafting Committee
Current Stage
Ref Project

Relations

Buy Standard

Standard
ASTM D3014-19 - Standard Test Method for Flame Height, Time of Burning, and Loss of Mass of Rigid Thermoset Cellular Plastics in a Vertical Position
English language
5 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
REDLINE ASTM D3014-19 - Standard Test Method for Flame Height, Time of Burning, and Loss of Mass of Rigid Thermoset Cellular Plastics in a Vertical Position
English language
5 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D3014 − 19
Standard Test Method for
Flame Height, Time of Burning, and Loss of Mass of Rigid
1
Thermoset Cellular Plastics in a Vertical Position
This standard is issued under the fixed designation D3014; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 2. Referenced Documents
2
2.1 ASTM Standards:
1.1 This is a fire-test-response standard. This test method
D883 Terminology Relating to Plastics
covers a small-scale laboratory screening procedure for com-
D1622 Test Method for Apparent Density of Rigid Cellular
paring relative extent and time of burning and loss of mass of
Plastics
rigid thermoset cellular plastics. This test method is to be used
D5025 Specification for Laboratory Burner Used for Small-
solely to establish relative burning characteristics.
Scale Burning Tests on Plastic Materials
1.1.1 This test method shall not be used for materials that
E176 Terminology of Fire Standards
drip or melt under the test conditions.
E456 Terminology Relating to Quality and Statistics
E691 Practice for Conducting an Interlaboratory Study to
1.2 During the course of combustion, gases or vapors, or
Determine the Precision of a Test Method
both,areevolvedwhicharepotentiallyhazardoustopersonnel.
E2935 Practice for Conducting Equivalence Testing in
Adequate precautions shall be taken to protect the operator.
Laboratory Applications
1.3 This standard does not purport to address all of the
3
2.2 ISO Standard:
safety concerns, if any, associated with its use. It is the
ISO 13943 Fire Safety—Vocabulary
responsibility of the user of this standard to establish appro-
priate safety, health, and environmental practices and deter-
3. Terminology
mine the applicability of regulatory limitations prior to use. A
3.1 Definitions—For definitions of terms relating to plastics,
specific precautionary statement is given in 1.2.
the definitions in this test method are in accordance with
1.4 This standard is used to measure and describe the
Terminology D883. For terms relating to fire, the definitions in
response of materials, products, or assemblies to heat and
this test method are in accordance with Terminology E176 and
flame under controlled conditions, but does not by itself
ISO 13943. In case of conflict, the definitions given in Termi-
incorporate all factors required for fire hazard or fire risk
nology E176 shall prevail. For terms relating to precision and
assessment of materials, products, or assemblies under actual
bias and associated issues, the terms used in this test method
fire conditions.
are in accordance with the definitions in Terminology E456.
1.5 Fire testing is inherently hazardous. Adequate safe-
4. Summary of Test Method
guards for personnel and property shall be employed in
4.1 The specimen is mounted in a vertical chimney with a
conducting these tests.
glass front and ignited with a bunsen burner for 10 s. The
NOTE 1—There is no known ISO equivalent to this standard.
height and duration of flame and the mass percent retained by
1.6 This international standard was developed in accor-
the specimen are recorded.
dance with internationally recognized principles on standard-
5. Significance and Use
ization established in the Decision on Principles for the
Development of International Standards, Guides and Recom-
5.1 Tests made on rigid cellular materials in accordance
mendations issued by the World Trade Organization Technical
with the conditions described by this test method can be of
Barriers to Trade (TBT) Committee.
considerable value in comparing their burning characteristics.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
1
This test method is under the jurisdiction ofASTM Committee D20 on Plastics contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
and is the direct responsibility of Subcommittee D20.30 on Thermal Properties Standards volume information, refer to the standard’s Document Summary page on
Current edition approved Aug. 1, 2019. Published August 2019. Originally the ASTM website.
3
approved in 1973. Last previous edition approved in 2018 as D3014 - 18. DOI: Available fromAmerican National Standards Institute (ANSI), 25 W. 43rd St.,
10.1520/D3014-19. 4th Floor, New York, NY 10036, http://www.ansi.org.
*A Summary of Changes section appears at the end of this standard
Copyright ©ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA19428-2959. United States
1

---------------------- Page: 1 ----------------------
D3014 − 19
FIG. 1 Critical Dimensions of Chimney
5.2 This test method has been applied to flexible cel
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D3014 − 18 D3014 − 19
Standard Test Method for
Flame Height, Time of Burning, and Loss of Mass of Rigid
1
Thermoset Cellular Plastics in a Vertical Position
This standard is issued under the fixed designation D3014; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This is a fire-test-response standard. This test method covers a small-scale laboratory screening procedure for comparing
relative extent and time of burning and loss of mass of rigid thermoset cellular plastics. This test method is to be used solely to
establish relative burning characteristics and shall not be considered or used as a fire-hazard classification.characteristics.
1.1.1 This test method shall not be used for materials that drip or melt under the test conditions.
1.2 During the course of combustion, gases or vapors, or both, are evolved which are potentially hazardous to personnel.
Adequate precautions shall be taken to protect the operator.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of
regulatory limitations prior to use. A specific precautionary statement is given in 1.2.
1.4 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under
controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of materials,
products, or assemblies under actual fire conditions.
1.5 Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these
tests.
NOTE 1—There is no known ISO equivalent to this standard.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
D883 Terminology Relating to Plastics
D1622 Test Method for Apparent Density of Rigid Cellular Plastics
D5025 Specification for Laboratory Burner Used for Small-Scale Burning Tests on Plastic Materials
E176 Terminology of Fire Standards
E456 Terminology Relating to Quality and Statistics
E691 Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
E2935 Practice for Conducting Equivalence Testing in Laboratory Applications
3
2.2 ISO Standard:
ISO 13943 Fire Safety—Vocabulary
3. Terminology
3.1 Definitions—For definitions of terms relating to plastics, the definitions in this test method are in accordance with
Terminology D883. For terms relating to fire, the definitions in this test method are in accordance with Terminology E176 and
1
This test method is under the jurisdiction of ASTM Committee D20 on Plastics and is the direct responsibility of Subcommittee D20.30 on Thermal Properties
Current edition approved May 1, 2018Aug. 1, 2019. Published June 2018August 2019. Originally approved in 1973. Last previous edition approved in 20112018 as
D3014 - 11.D3014 - 18. DOI: 10.1520/D3014-18.10.1520/D3014-19.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D3014 − 19
FIG. 1 Critical Dimensions of Chimney
ISO 13943. In case of conflict, the definitions given in Terminology E176. shall prevail. For terms relating to precision and bias
and associated issues, the terms used in this test method are in accordance with the definitions in Terminology E456.
4. Summary of Test Method
4.1 The specimen is mounted in a vertic
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.