iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D4111-02

(Specification)

Standard Performance Specification for Woven Napery and Tablecloth Fabrics Household and Institutional (Withdrawn 2011)

Standard Performance Specification for Woven Napery and Tablecloth Fabrics Household and Institutional (Withdrawn 2011)

SCOPE
1.1 This performance specification covers woven fabrics comprised of any textile fiber or mixture of fibers to be used in napery and tablecloths (household and institutional).
1.2 These requirements apply to both the length and width directions for those properties where fabric direction is pertinent.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
WITHDRAWN RATIONALE
This performance specification covers woven fabrics comprised of any textile fiber or mixture of fibers to be used in napery and tablecloths (household and institutional).
Formerly under the jurisdiction of Committee D13 on Textiles and the direct responsibility of Subcommittee D13.63 on Home Furnishings, this performance specification was withdrawn in January 2011 in accordance with section 10.5.3.1 of the Regulations Governing ASTM Technical Committees, which requires that standards shall be updated by the end of the eighth year since the last approval date.

General Information

Status
Historical
Publication Date
09-Apr-2002
Withdrawal Date
31-Dec-2010
ICS
97.160 - Home textiles. Linen
Technical Committee
D13 - Textiles
Drafting Committee
D13.63 - Home Furnishings
Current Stage
Ref Project

Relations

Replaces
ASTM D4111-95(2001) - Standard Performance Specification for Woven Napery and Tablecloth Fabrics Household and Institutional
Effective Date
10-Apr-2002
Replaced By
ASTM D4111-12 - Standard Performance Specification for Woven Napery and Tablecloth Fabrics: Household and Institutional
Effective Date
01-Feb-2012

Buy Standard

ASTM D4111-02 - Standard Performance Specification for Woven Napery and Tablecloth Fabrics Household and Institutional (Withdrawn 2011)ASTM D4111-02 - Standard Performance Specification for Woven Napery and Tablecloth Fabrics Household and Institutional (Withdrawn 2011)
PreviousNext
Technical specification
ASTM D4111-02 - Standard Performance Specification for Woven Napery and Tablecloth Fabrics Household and Institutional (Withdrawn 2011)
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D4111 – 02
Standard Performance Specification for
Woven Napery and Tablecloth Fabrics: Household and
1
Institutional
This standard is issued under the fixed designation D4111; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
4
1. Scope 2.2 AATCC Methods:
8 Colorfastness to Crocking: AATCC Crockmeter Method
1.1 This performance specification covers woven fabrics
16 Colorfastness to Light
comprised of any textile fiber or mixture of fibers to be used in
23 Colorfastness to Burnt Gas Fumes
napery and tablecloths (household and institutional).
61 Colorfastness to Washing, Domestic, and Laundering,
1.2 These requirements apply to both the length and width
Commercial: Accelerated
directions for those properties where fabric direction is perti-
92 Chlorine, Retained,Tensile Loss: Single Sample Method
nent.
96 Dimensional Changes in Laundering of Woven and
1.3 This standard does not purport to address all of the
Knitted Textiles Except Wool
safety concerns, if any, associated with its use. It is the
116 Colorfastness to Crocking: Rotary Vertical Crockmeter
responsibility of the user of this standard to establish appro-
Method
priate safety and health practices and determine the applica-
124 Appearance of Durable Press Fabrics After Repeated
bility of regulatory limitations prior to use.
Home Launderings
2. Referenced Documents 130 Soil Release: Oily Stain Release Method
2
135 Dimensional Changes inAutomatic Home Laundering
2.1 ASTM Standards:
of Woven or Knit Fabrics
D123 Terminology Relating to Textiles
172 Colorfastness to Non-Chlorine Bleach in Home Laun-
D1336 TestMethodforDistortionofYarninWovenFabrics
dering
D1424 Test Method for Tearing Strength of Fabrics by
188 Colorfastness to Chlorine Bleach in Home Laundering
Falling-Pendulum (Elmendorf-Type) Apparatus
Evaluation Procedure No. 1 Gray Scale for Color Change
D1682 Standard Methods of Test for Breaking Load and
3
Evaluation Procedure No. 2 Gray Scale for Staining
Elongation of Textile Fabrics
Evaluation Procedure No. 3 AATCC Chromatic Transfer-
D2261 Test Method for Tearing Strength of Fabrics by the
ence Scale
Tongue (Single Rip) Procedure (Constant-Rate-of-
5
2.3 Federal Standard:
Extension Tensile Testing Machine)
16 CFR, Chapter II–Consumer Product Safety Commission
D2262 Test Method for Tearing Strength of Woven Fabrics
Subchapter D–Flammable Fabrics Act Regulations
by the Tongue (Single Rip) Method (Constant-Rate-of-
6
3
2.4 Military Standard:
Traverse Tensile Testing Machine)
MIL-STD-105D Sampling Procedures and Tables for In-
D2724 Test Methods for Bonded, Fused, and Laminated
spection by Attributes
Apparel Fabrics
D2905 PracticeforStatementsonNumberofSpecimensfor
NOTE 1—Reference to test methods in this specification give only the
3
Textiles
permanent part of the designation of ASTM, AATCC, or other test
1
This specification is under the jurisdiction of ASTM Committee D13 on
Textiles and is the direct responsibility of Subcommittee D13.63 on Home
Furnishings.
Current edition approved April 10, 2002. Published June 2002. Originally
published as D4111 – 82. Last previous edition D4111 – 95(2001). DOI: 10.1520/
D4111-02.
2 4
For referenced ASTM standards, visit the ASTM website, www.astm.org, or Available from American Association of Textile Chemists and Colorists, P.O.
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Box 12215, Research Triangle Park, NC 27709.
5
Standards volume information, refer to the standard’s Document Summary page on Available from Superintendent of Documents, Government Printing Office,
the ASTM website. Washington, DC 20402.
3 6
Withdrawn. The last approved version of this historical standard is referenced AvailablefromStandardizationDocumentsOrderDesk,Bldg.4SectionD,700
on www.astm.org. Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.
Copyright ©ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA19428-2959, United States.
1

---------------------- Page: 1 ----------------------
D4111–02
methods. The current editions of each test method cited shall prevail.
5.3 Where no prepurchase agreement has been reached
between the purchaser and the seller, and in case of contro-
3. Terminology
versy,therequirementslistedinTable1areintendedtobeused
3.1 Definitions:
as a guide only. As noted in 5.2, ultimate consumer demands
3.1.1 For definitions of textile terms used in this specifica-
dictate varying performance parameters for any particular style
tion refer to the individualASTM andAATCC methods and to
of fabric.
Terminology D123.
5.4 The uses and significance o
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D4151-23(Test Method)
Standard Test Method for Flammability of Blankets

SIGNIFICANCE AND USE
5.1 This test method for the determination of the flammability of blankets is considered satisfactory for acceptance testing of commercial shipments of blankets since this test method has been used extensively in the trade for acceptance testing.  
5.2 This test method is intended to evaluate fabrics used in electric blankets without the resistance heating wires.  
5.3 Fabrics are potentially combustible. Some fabrics when used for blankets are potentially dangerous to the user depending on the ease of ignition, rapidity, and intensity of burning. This test method addresses some of these characteristics.
SCOPE
1.1 This test method provides a means to identify blanket fabrics which ignite easily and propagate flame across the surface.  
1.2 This test method specifies the procedures described in the “Voluntary Blanket Flammability Standard” which has been used by the blanket industry in the United States since 1972.  
1.3 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products or assemblies under actual fire conditions.
Note 1: This test method is not identical to 16 CFR Part 1610, Flammability of Clothing Textiles. Consumer Product Safety Commission regulations require that fabrics introduced into commerce meet the requirements of 16 CFR Part 1610.  
1.4 Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    8 pages
    English language
    sale 15% off
  • Standard
    8 pages
    English language
    sale 15% off
ASTM
ASTM D6545-22(Test Method)
Standard Test Method for Flammability of Textiles Used in Children's Sleepwear

SIGNIFICANCE AND USE
5.1 This test method is suitable for evaluating flammability characteristics and laundering durability of textiles used in the manufacture of children's sleepwear. It is not suitable for evaluating the flammability characteristics of textiles for other product applications or ignition scenarios.  
5.2 The procedure for flammability testing used in this test method is technically equivalent to those used in 16 CFR 1615 and 1616. This test method does not include detailed specimen sampling plans, or the regulatory and record keeping requirements cited in the federal regulations. Please consult 16 CFR 1615 and 1616 for information for these operations.  
5.3 This test method is suitable for training technicians to conduct the federal test and can serve as a laboratory reference.  
5.4 Test Method D6545 is very different from 16 CFR 1610 and from Test Method D1230.
SCOPE
1.1 This test method evaluates the relative flammability of textiles and garments intended for use in children's sleepwear. The procedures of this test method follow testing and laundering procedures used to evaluate the flammability of children's sleepwear contained in U.S. Federal Regulations 16 CFR 1615 and 1616.  
1.2 A textile used in children's sleepwear must be tested in its original state and after 50 laundering and drying cycles to assess the flame resistance of the textile relative to its use life.  
1.3 This method is identical to the method outlined in the regulations 16 CFR 1615 or 1616. The regulation includes additional information such as sampling plans, record keeping requirements, and interpretations for compliance applicable to children’s sleepwear. Please consult 16 CFR 1615 and 1616 for these operations and interpretations.  
1.4 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.  
1.5 This test method is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions.  
1.6 Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental health practices and determines the applicability of regulatory limitations prior to use. Specific precautionary information is found in 8.5 and 9.5.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    10 pages
    English language
    sale 15% off
  • Standard
    10 pages
    English language
    sale 15% off
ASTM
ASTM D4037-02(2019)(Specification)
Standard Performance Specification for Woven, Knitted, or Flocked Bedspread Fabrics

SIGNIFICANCE AND USE
4.1 Fabrics intended for this end-use should meet all of the requirements listed in Table 1.  
4.2 It should be recognized that fabrics can be produced with an almost infinite number of construction variables (for example, type of fibers, percentage of fibers, yarn twist, yarn number, warp and pick count, chemical and mechanical finishes). Additionally, fashion or aesthetics dictate that the ultimate consumer may find acceptable articles made from fabrics that do not conform to all of the requirements in Table 1.  
4.2.1 Hence, no single performance specification can possibly apply to all the various fabrics that could be utilized for this end-use.  
4.3 The uses and significance of particular properties and test methods are discussed in the appropriate sections of the specified test methods.
SCOPE
1.1 This performance specification covers the performance requirements for woven, knitted, or flocked fabrics to be used in the manufacturing of bedspreads.  
1.2 These requirements apply to the length and width directions for those properties where fabric direction is pertinent.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM D4113-02(2019)(Specification)
Standard Performance Specification for Woven Slipcover Fabrics

SIGNIFICANCE AND USE
5.1 Fabrics intended for this end-use should meet all of the requirements listed inTable 1 .  
5.2 It should be recognized that fabrics can be produced with an almost infinite number of combination of construction variables (for example, type of fibers, percentage of fibers, yarn twist, yarn number, warp and pick count, chemical and mechanical finishes). Additionally, fashion or aesthetics dictate that the ultimate consumer may find acceptable articles made from fabrics that do not conform to all of the requirements in Table 1.  
5.2.1 Hence, no single performance specification can possibly apply to all the various fabrics that could be utilized for this end-use.  
5.3 The uses and significance of particular properties and test methods are discussed in the appropriate sections of the specified test methods.
SCOPE
1.1 This performance specification covers woven fabrics comprised of any textile fiber or mixture of fibers to be used in slipcovers.  
1.2 These requirements apply to both the length and width directions for those properties where fabric direction is pertinent.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM D4111-12(2019)(Specification)
Standard Performance Specification for Woven Napery and Tablecloth Fabrics: Household and Institutional

SIGNIFICANCE AND USE
5.1 Upon agreement between the purchaser and the seller, fabrics intended for this end use should meet all of the requirements listed in Table 1 of this specification.  
5.2 It is recognized that for purposes of fashion or aesthetics the ultimate consumer of articles made from these fabrics may find acceptable fabrics that do not conform to all of the requirements in Table 1. Therefore, one or more of the requirements listed in Table 1 may be modified upon agreement between the purchaser and the seller.  
5.2.1 In such cases, any references to the specification shall specify that: “This fabric meets ASTM Specification D4111 except for the following characteristic(s).”  
5.3 Where no prepurchase agreement has been reached between the purchaser and the seller, and in case of controversy, the requirements listed in Table 1 are intended to be used as a guide only. As noted in 5.2, ultimate consumer demands dictate varying performance parameters for any particular style of fabric.  
5.4 The uses and significance of particular properties and methods are discussed in the appropriate sections of the specified methods.
SCOPE
1.1 This performance specification covers woven fabrics comprised of any textile fiber or mixture of fibers to be used in napery and tablecloths (household and institutional).  
1.2 These requirements apply to both the length and width directions for those properties where fabric direction is pertinent.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM D5378-12(2019)(Specification)
Standard Performance Specification for Woven and Knitted Shower Curtains for Institutional and Household Use

SIGNIFICANCE AND USE
4.1 Upon mutual agreement between the purchaser and the supplier, woven and knitted products intended for this end use should meet all of the requirements listed in Table 1 of this specification.  
4.2 It is recognized that for the purposes of fashion or aesthetics the ultimate consumer of articles made from these fabrics may find acceptable products that do not conform to all of the requirements in Table 1. Therefore, one or more of the requirements listed in Table 1 may be modified by mutual agreement between the purchaser and the seller.  
4.2.1 In such cases, any references to the specification shall specify that: this product meets Specification D5378 except for the following characteristic(s).  
4.3 Where no prepurchase agreement has been reached between the purchaser and the supplier, and in case of controversy, the requirements listed in Table 1 are intended to be used as a guide only. As noted in 4.2, ultimate consumer demands dictate varying performance parameters for any particular style.  
4.4 The significance and uses of particular properties and test methods are discussed in the appropriate sections of the specified test methods.
SCOPE
1.1 This specification covers the evaluation of specific performance characteristics of importance in woven and knitted shower curtains for use in institutional and household environments.  
1.2 This specification may be used by mutual agreement between purchaser and supplier to establish purchasing specification requirements.  
1.3 The requirements in Table 1 apply to the length and width directions for those properties where fabric direction is pertinent.  
1.4 This specification is not applicable for coated, laminated or vinyl product.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM D4720-08(2019)(Specification)
Standard Performance Specification for Soft Window Covering Fabrics for Household Use

ABSTRACT
This performance specification establishes the evaluation of specific performance characteristics of any washable or dry-cleanable soft window covering fabrics, whether lined or unlined, for household use. The characteristics to be evaluated prior to repeated refurbishing include, but are not limited to, seam strength and appearance, uniformity of shade (part to part), and size consistency (side to side and part to part). Consequently, the characteristics to be evaluated after repeated refurbishing include, but are not limited to, colorfastness, dimensional change, seam strength, appearance, and compatibility of components. Compatibility of dimensional change between drapery fabric and lining should be noted.
SIGNIFICANCE AND USE
4.1 This specification may be used to evaluate pertinent performance characteristics of washable and drycleanable soft window coverings, whether lined or unlined.  
4.1.1 Soft window covering characteristics to be evaluated prior to repeated refurbishing include, but are not limited to, seam strength and appearance, uniformity of shade (part to part), and size consistency (side to side and part to part).  
4.1.2 Soft window covering characteristics to be evaluated after repeated refurbishing include, but are not limited to, colorfastness, dimensional change, seam strength, appearance, and compatibility of components. Compatibility of dimensional change between drapery fabric and lining should be noted.  
4.2 The specified home laundry machine settings do not reflect advances in cycle design or special features of washer and dryers which enhance the performance of these products. The standard washing and drying procedure reflects the minimum capabilities of current home laundering equipment used by consumers in accordance with care label instructions.  
4.2.1 The reproducibility of the results of the test method specified in 9.2 depends on the use of procedures for automatic home laundering as specified on care labels.  
4.3 The areas to be evaluated and the criteria assigned to these areas shall be set by mutual agreement between purchaser and supplier.
SCOPE
1.1 This specification covers the evaluation of specific performance characteristics of any washable or drycleanable soft window covering.  
1.2 This specification is not a specification for washable or drycleanable soft window coverings but may be used by mutual agreement between the purchaser and the supplier to establish material specifications.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM D5433-12(2019)(Specification)
Standard Performance Specification for Towel Products for Institutional and Household Use

SIGNIFICANCE AND USE
5.1 Upon mutual agreement between the purchaser and the supplier, woven or knitted products intended for this end use should meet all of the requirements listed in Table 1 of this specification for terry products and Table 2 for non terry products.  
5.2 It is recognized that for purposes of fashion or aesthetics the ultimate consumer of articles made from these fabrics may find acceptable products that do not conform to all of the requirements in Table 1 or Table 2. Therefore, one or more of the requirements listed in Table 1 or Table 2 may be modified by mutual agreement between the purchaser and the seller.  
5.2.1 In such cases, any references to the specification shall specify that: This product meets ASTM Specification 63-707 except for the following characteristic(s).  
5.3 Where no prepurchase agreement has been reached between the purchaser and the supplier, and in case of controversy, the requirements listed in Table 1 or Table 2 are intended to be used as a guide only. As noted in 5.2, ultimate consumer demands dictate varying performance parameters for any particular style.  
5.4 The significance and use of particular properties and test methods are discussed in the appropriate sections of the specified test methods.
SCOPE
1.1 This specification covers the evaluation of specific performance characteristics of importance in woven and knitted kitchen towel, dishcloth, crash towel, huck towel, washcloth, hand towel, bath towel, and bath sheet products for use in institutional and household environments.  
1.2 This specification may be used by mutual agreement between the purchaser and the supplier to establish purchasing specification requirements.  
1.3 The requirements in Tables 1 and 2 apply to the length and width directions for those properties where fabric direction is pertinent.    
1.4 This specification is not applicable for coated and laminated products, nonwoven products, or terry fabrics used for apparel.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM D5432-12(2019)(Specification)
Standard Performance Specification for Blanket Products for Institutional and Household Use

SIGNIFICANCE AND USE
4.1 Upon mutual agreement between the purchaser and the supplier, woven products intended for this end use should meet all of the requirements listed in Table 1 of this specification.  
4.2 It is recognized that for purposes of fashion or aesthetics the ultimate consumer of articles made from these fabrics may find acceptable products that do not conform to all of the requirements in Table 1. Therefore, one or more of the requirements listed in Table 1 may be modified by mutual agreement between the purchaser and the supplier.  
4.2.1 In such cases, any references to the specification shall specify that: This product meets Specification D5432 except for the following characteristic(s).  
4.3 Where no prepurchase agreement has been reached between the purchaser and the supplier, and in case of controversy, the requirements listed in Table 1 are intended to be used as a guide only. As noted in 4.2, ultimate consumer demands dictate varying performance parameters for any particular style.  
4.4 The significance and use of particular properties and test methods are discussed in the appropriate sections of the specified test methods.
SCOPE
1.1 This specification covers the evaluation of specific performance characteristics of importance in thermal woven, conventional woven, flocked, nonwoven, and knitted blanket products for use in institutional and household environments.  
1.2 This specification may be used by mutual agreement between the purchaser and the supplier to establish purchasing specification requirements.  
1.3 The requirements in Table 1 apply to the length and width directions for those properties where fabric direction is pertinent.  
1.4 This specification does not include requirements for electric blankets. Electric blankets are specified under UL 964 requirements dictated by the Underwriter's Laboratories.  
1.5 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM D6663-08(2019)(Specification)
Standard Specification for Woven and Knitted Comforter and Accessory Products for Institutional and Household Use

SCOPE
1.1 This specification covers the evaluation of specific performance characteristics of importance in woven and knit comforter and accessory products, except for pillows and window treatments, for use in institutional and household environments.  
1.2 The following safety hazards caveat pertains only to the test methods described in this specification:This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off