Standard Specification for General Requirements for Carbon and Low Alloy Steel Tubes

ABSTRACT
This specification covers carbon and low alloy steel tubes. Steel samples shall be melt processed and shall either be ingot cast or strand cast. Heat and product analyses shall be performed on the steel materials. Steel specimens shall also undergo tensile tests and shall conform to required values of yield strength and elongation. Flattening test, reverse flattening test, flaring test, flange test, hardness test, hydrostatic test, air underwater pressure test, and nondestructive tests shall be performed on the steel materials.
SCOPE
1.1 This specification2 covers a group of requirements which, with the exceptions of 6.3 and Sections 7, 8, 19, 20, 21, 22, 23, 24, and 25, are mandatory requirements to the following ASTM tubular product specifications:3    
Title of Specification  
ASTM DesignationA  
Electric-Resistance-Welded Carbon Steel and Carbon-Manganese Steel Boiler Tubes  
A178/A178M    
Seamless Cold-Drawn Low-Carbon Steel Heat-Exchanger and Condenser Tubes  
A179/A179M  
Seamless Carbon Steel Boiler Tubes for High-Pressure Service  
A192/A192M    
Seamless Medium-Carbon Steel Boiler and Superheater Tubes  
A210/A210M    
Electric-Resistance-Welded Carbon Steel Heat-Exchanger and Condenser Tubes  
A214/A214M    
Seamless and Electric-Welded Low-Alloy Steel Tubes  
A423/A423M    
Specification for Seamless and Welded Carbon Steel Heat-Exchanger Tubes with Integral Fins  
A498/A498M  
Seamless Cold-Drawn Carbon Steel Feedwater Heater Tubes  
A556/A556M  
Seamless, Cold-Drawn Carbon Steel Tubing for Hydraulic System Service  
A822/A822M
1.2 One or more of Sections 6.3, 7, 8, 19, 20, 21, 22, 22.1, 24, and 25 apply when the product specification or purchase order has a requirement for the test or analysis described by these sections.  
1.3 In case of conflict between a requirement of the product specification and a requirement of this general requirement specification only the requirement of the product specification need be satisfied.  
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the “M” designation (SI) of the product specification is specified in the order.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

Status
Published
Publication Date
31-Oct-2023
Current Stage
Ref Project

Relations

Buy Standard

Technical specification
ASTM A450/A450M-23 - Standard Specification for General Requirements for Carbon and Low Alloy Steel Tubes
English language
10 pages
sale 15% off
Preview
sale 15% off
Preview
Technical specification
REDLINE ASTM A450/A450M-23 - Standard Specification for General Requirements for Carbon and Low Alloy Steel Tubes
English language
10 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: A450/A450M − 23
Standard Specification for
General Requirements for Carbon and Low Alloy Steel
1
Tubes
This standard is issued under the fixed designation A450/A450M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope* SI units are shown in brackets. The values stated in each
2 system may not be exact equivalents; therefore, each system
1.1 This specification covers a group of requirements
shall be used independently of the other. Combining values
which, with the exceptions of 6.3 and Sections 7, 8, 19, 20, 21,
from the two systems may result in non-conformance with the
22, 23, 24, and 25, are mandatory requirements to the follow-
3 standard. The inch-pound units shall apply unless the “M”
ing ASTM tubular product specifications:
designation (SI) of the product specification is specified in the
A
Title of Specification ASTM Designation
order.
Electric-Resistance-Welded Carbon Steel and Carbon- A178/A178M
1.5 This international standard was developed in accor-
Manganese Steel Boiler Tubes
dance with internationally recognized principles on standard-
Seamless Cold-Drawn Low-Carbon Steel Heat- A179/A179M
Exchanger and Condenser Tubes ization established in the Decision on Principles for the
Seamless Carbon Steel Boiler Tubes for High-Pressure A192/A192M
Development of International Standards, Guides and Recom-
Service
mendations issued by the World Trade Organization Technical
Seamless Medium-Carbon Steel Boiler and Super- A210/A210M
heater Tubes
Barriers to Trade (TBT) Committee.
Electric-Resistance-Welded Carbon Steel Heat- A214/A214M
Exchanger and Condenser Tubes
2. Referenced Documents
Seamless and Electric-Welded Low-Alloy Steel Tubes A423/A423M
4
Specification for Seamless and Welded Carbon Steel A498/A498M 2.1 ASTM Standards:
Heat-Exchanger Tubes with Integral Fins
A178/A178M Specification for Electric-Resistance-Welded
Seamless Cold-Drawn Carbon Steel Feedwater Heater A556/A556M
Carbon Steel and Carbon-Manganese Steel Boiler and
Tubes
Seamless, Cold-Drawn Carbon Steel Tubing for Hy- A822/A822M
Superheater Tubes
draulic System Service
A179/A179M Specification for Seamless Cold-Drawn Low-
Carbon Steel Heat-Exchanger and Condenser Tubes
A
These designations refer to the latest issue of the respective specifications.
A192/A192M Specification for Seamless Carbon Steel
1.2 One or more of Sections 6.3, 7, 8, 19, 20, 21, 22, 22.1,
Boiler Tubes for High-Pressure Service
24, and 25 apply when the product specification or purchase
A210/A210M Specification for Seamless Medium-Carbon
order has a requirement for the test or analysis described by
Steel Boiler and Superheater Tubes
these sections.
A214/A214M Specification for Electric-Resistance-Welded
Carbon Steel Heat-Exchanger and Condenser Tubes
1.3 In case of conflict between a requirement of the product
A370 Test Methods and Definitions for Mechanical Testing
specification and a requirement of this general requirement
of Steel Products
specification only the requirement of the product specification
A423/A423M Specification for Seamless and Electric-
need be satisfied.
Welded Low-Alloy Steel Tubes
1.4 The values stated in either SI units or inch-pound units
A498/A498M Specification for Seamless and Welded Car-
are to be regarded separately as standard. Within the text, the
bon Steel Heat-Exchanger Tubes with Integral Fins
A530/A530M Specification for General Requirements for
1 Specialized Carbon and Alloy Steel Pipe
This specification is under the jurisdiction of ASTM Committee A01 on Steel,
Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee
A556/A556M Specification for Seamless Cold-Drawn Car-
A01.09 on Carbon Steel Tubular Products.
bon Steel Feedwater Heater Tubes
Current edition approved Nov. 1, 2023. Published November 2023. Originally
approved in 1961. Last previous edition approved in 2021 as A450/A450M – 21.
4
DOI: 10.1520/A0450_A0450M-23. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
2
For ASME Boiler and Pressure Vessel Code applications see related Specifi- contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
cation SA-450 in Section II of that Code. Standards volume information, refer to the standard’s Document Summary page on
3
Annual Book of ASTM Standards, Vols 01.01 and 01.04. the ASTM website.
*A Summary of Changes section ap
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: A450/A450M − 21 A450/A450M − 23
Standard Specification for
General Requirements for Carbon and Low Alloy Steel
1
Tubes
This standard is issued under the fixed designation A450/A450M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope*
2
1.1 This specification covers a group of requirements which, with the exceptions of 6.3 and Sections 7, 8, 19, 20, 21, 22, 23, 24,
3
and 25, are mandatory requirements to the following ASTM tubular product specifications:
A
Title of Specification ASTM Designation
Electric-Resistance-Welded Carbon Steel and Carbon- A178/A178M
Manganese Steel Boiler Tubes
Seamless Cold-Drawn Low-Carbon Steel Heat- A179/A179M
Exchanger and Condenser Tubes
Seamless Carbon Steel Boiler Tubes for High-Pressure A192/A192M
Service
Seamless Medium-Carbon Steel Boiler and Super- A210/A210M
heater Tubes
Electric-Resistance-Welded Carbon Steel Heat- A214/A214M
Exchanger and Condenser Tubes
Seamless and Electric-Welded Low-Alloy Steel Tubes A423/A423M
Specification for Seamless and Welded Carbon Steel A498/A498M
Heat-Exchanger Tubes with Integral Fins
Seamless Cold-Drawn Carbon Steel Feedwater Heater A556/A556M
Tubes
Seamless, Cold-Drawn Carbon Steel Tubing for Hy- A822/A822M
draulic System Service
A
These designations refer to the latest issue of the respective specifications.
1.2 One or more of Sections 6.3, 7, 8, 19, 20, 21, 22, 22.1, 24, and 25 apply when the product specification or purchase order has
a requirement for the test or analysis described by these sections.
1.3 In case of conflict between a requirement of the product specification and a requirement of this general requirement
specification only the requirement of the product specification need be satisfied.
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel, Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee A01.09
on Carbon Steel Tubular Products.
Current edition approved Nov. 1, 2021Nov. 1, 2023. Published November 2021November 2023. Originally approved in 1961. Last previous edition approved in 20182021
as A450/A450M – 18a.A450/A450M – 21. DOI: 10.1520/A0450_A0450M-21.10.1520/A0450_A0450M-23.
2
For ASME Boiler and Pressure Vessel Code applications see related Specification SA-450 in Section II of that Code.
3
Annual Book of ASTM Standards, Vols 01.01 and 01.04.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
A450/A450M − 23
are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used
independently of the other. Combining values from the two systems may result in non-conformance with the standard. The
inch-pound units shall apply unless the “M” designation (SI) of the product specification is specified in the order.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
4
2.1 ASTM Standards:
A178/A178M Specification for Electric-Resistance-Welded Carbon Steel and Carbon-Manganese Steel Boiler and Superheater
Tubes
A179/A179M Specification for Seamless Cold-Drawn Low-Carbon Steel Heat-Exchanger and Condenser Tubes
A192/A192M Specification for Seamless Carbon Steel Boiler Tubes for High-Pressure Service
A210/A210M Specification for Seamless Medium-Carbon Steel Boiler and Superheater Tubes
A214/A214M Specification for Electric-Resistance-Welded Carbon Steel Heat-Exchanger and Condenser Tubes
A370 Test Methods and Definitions for Mechanical Testing of Steel Products
A423/A423M Specification for Seamless and Electric-Welded Low-Alloy Steel Tubes
A498/A498M Specification for Seamless and Welded Carbon Steel Heat-Exchanger Tubes with Integral Fins
A530/
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.