ASTM D2276-06

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D2276 − 06
Designation:216/97 An American National Standard
Standard Test Method for
1
Particulate Contaminant in Aviation Fuel by Line Sampling
This standard is issued under the fixed designation D2276; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope* 2. Referenced Documents
2
1.1 This test method covers the determination of particulate 2.1 ASTM Standards:
contaminant in aviation turbine fuel using a field monitor. D1193Specification for Reagent Water
D1535Practice for Specifying Color by the Munsell System
1.2 There are two test methods described. The basic test
D1655Specification for Aviation Turbine Fuels
method is used to evaluate the level of contamination gravi-
D2244Practice for Calculation of Color Tolerances and
metrically.Thesecondtestmethod,presentedinAppendixX1,
Color Differences from Instrumentally Measured Color
describes a color rating technique that is used for rapid
Coordinates
qualitative assessment of changes in contamination level with-
D4865Guide for Generation and Dissipation of Static Elec-
out the time delay required for the gravimetric determinations
tricity in Petroleum Fuel Systems
by stringent laboratory procedures.
D5452Test Method for Particulate Contamination in Avia-
1.3 There are twoAnnexes and twoAppendixes in this test
tion Fuels by Laboratory Filtration
method.
D6615Specification for Jet B Wide-Cut Aviation Turbine
1.3.1 Annex A1 provides some precautionary information
Fuel
regarding the use of the required reagents.
1.3.2 Annex A2 describes a standard practice for obtaining
3. Terminology
a sample of the particulates present in a flowing stream of
3.1 Definitions:
aviation turbine fuel.
3.1.1 membrane color, n—a visual rating of particulate on a
1.3.3 Appendix X1 describes a test method for rating the
filter membrane against ASTM Color Standards.
particulate level in an aviation turbine fuel on the basis of the
3.1.2 membrane filter, n—a porous article of closely con-
color of a filter membrane after sampling the fuel in the field.
1.3.4 Appendix X2 provides some safety precautions to trolled pore size through which a liquid is passed to separate
matter in suspension.
avoid static discharge resulting from the accumulation of
3
electrical charges in the fuel and on the equipment while 3.1.2.1 Discussion— RR:D02-1012 contains information
on membrane filters that meet the requirements therein.
following the procedures.
3.1.3 monitor, n—something that reminds or warns.
1.4 The values stated in SI units are to be regarded as the
3.1.3.1 Discussion—A plastic holder for a membrane filter
standard. The values given in parentheses are for information
held in a field sampling apparatus.
only.
3.1.4 particulate, adj—of or relating to minute separate
1.5 This standard does not purport to address all of the
particles.
safety concerns, if any, associated with its use. It is the
3.1.4.1 Discussion—Solids generally composed of oxides,
responsibility of the user of this standard to establish appro-
silicates, and fuel insoluble salts.
priate safety and health practices and determine the applica-
bility of regulatory limitations prior to use.
1 2
This test method is under the jurisdiction of ASTM Committee D02 on For referenced ASTM standards, visit the ASTM website, www.astm.org, or
PetroleumProductsandLubricantsandisthedirectresponsibilityofSubcommittee contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
D02.J0.05 on Fuel Cleanliness. Standards volume information, refer to the standard’s Document Summary page on
This test method has been approved by the sponsoring committees and accepted the ASTM website.
3
by the Cooperating Societies in accordance with established procedures. Supportingdata(andalistofsupplierswhohaveprovideddataindicatingtheir
Current edition approved Dec. 1, 2006. Published January 2007. Originally membranes, field monitors, and field monitor castings) have been filed at ASTM
approved in 1964. Last previous edition approved in 2005 as D2276–05. DOI: International Headquarters and may be obtained by requesting Research Report
10.1520/D2276-06. RR:D02-1012.
*A Summary of Changes section appears at the end of this standard
Copyright ©ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA19428-2959. United States
1

---------------------- Page: 1 ----------------------
D2276 − 06
3.2 Definitions of Terms Specific to This Standard:
3.2.1 volatile fuels, n—relativelywideboilingrangevolatile
distillate.
3.2.1.1 Discussion—These are id
...