iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D3815/D3815M-05(2011)

(Practice)

Standard Practice for Accelerated Weathering of Pressure-Sensitive Tapes by Open-Flame Carbon-Arc Exposure Apparatus

Standard Practice for Accelerated Weathering of Pressure-Sensitive Tapes by Open-Flame Carbon-Arc Exposure Apparatus

SIGNIFICANCE AND USE
This practice does not necessarily provide direct simulation of natural weathering exposure.
Results from use of this practice shall not be represented as being equivalent to those of any natural weathering test until a satisfactory degree of correlation has been established for the material in question.
Variations in results are possible when the operating conditions vary within the accepted limits for the instrument specified in Practices G151 and G152.
SCOPE
1.1 This practice describes one environment for the exposure of pressure-sensitive tapes to a laboratory accelerated weathering environment.  
1.2 This practice describes sample preparation and the laboratory-accelerated weathering environment to which it shall be exposed. It does not specify the length of time of the exposure nor what tests shall be performed on the material following the exposure.
Note 1—Practice D6551/D6551M describes xenon-arc exposures of tapes.
1.3 The values stated in either SI or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system must be used independently without combining values in any way.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
31-Jul-2011
ICS
55.040 - Packaging materials and accessories
Technical Committee
D10 - Packaging
Drafting Committee
D10.14 - Tape and Labels
Current Stage
Ref Project

Relations

Replaces
ASTM D3815/D3815M-05 - Standard Practice for Accelerated Weathering of Pressure-Sensitive Tapes by Open-Flame Carbon-Arc Exposure Apparatus
Effective Date
01-Aug-2011
Replaced By
ASTM D3815/D3815M-05(2019) - Standard Practice for Accelerated Weathering of Pressure-Sensitive Tapes by Open-Flame Carbon-Arc Exposure Apparatus
Effective Date
01-Apr-2019
Referred By
ASTM D5486/D5486M-06(2020) - Standard Specification for Pressure-Sensitive Tape for Packaging, Box Closure, and Sealing
Effective Date
01-Aug-2011
Referred By
ASTM D5330/D5330M-06(2020) - Standard Specification for Pressure-Sensitive Tape for Packaging, Filament-Reinforced
Effective Date
01-Aug-2011

Buy Standard

ASTM D3815/D3815M-05(2011) - Standard Practice for Accelerated Weathering of Pressure-Sensitive Tapes by Open-Flame Carbon-Arc Exposure ApparatusASTM D3815/D3815M-05(2011) - Standard Practice for Accelerated Weathering of Pressure-Sensitive Tapes by Open-Flame Carbon-Arc Exposure Apparatus
PreviousNext
Standard
ASTM D3815/D3815M-05(2011) - Standard Practice for Accelerated Weathering of Pressure-Sensitive Tapes by Open-Flame Carbon-Arc Exposure Apparatus
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D3815/D3815M − 05 (Reapproved 2011)
Standard Practice for
Accelerated Weathering of Pressure-Sensitive Tapes by
Open-Flame Carbon-Arc Exposure Apparatus
This standard is issued under the fixed designation D3815/D3815M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope Pressure-Sensitive Tapes by Xenon-Arc Exposure Appa-
ratus
1.1 This practice describes one environment for the expo-
G147 Practice for Conditioning and Handling of Nonmetal-
sure of pressure-sensitive tapes to a laboratory accelerated
lic Materials for Natural and Artificial Weathering Tests
weathering environment.
G151 Practice for Exposing Nonmetallic Materials inAccel-
1.2 This practice describes sample preparation and the
erated Test Devices that Use Laboratory Light Sources
laboratory-accelerated weathering environment to which it
G152 Practice for Operating Open Flame Carbon Arc Light
shall be exposed. It does not specify the length of time of the
Apparatus for Exposure of Nonmetallic Materials
exposure nor what tests shall be performed on the material
following the exposure.
3. Summary of Practice
NOTE 1—Practice D6551/D6551M describes xenon-arc exposures of
3.1 The pressure-sensitive tape is exposed in accordance
tapes.
with the conditions provided by Practices G151 and G152.
1.3 The values stated in either SI or inch-pound units are to
Exposure time is determined by applicable material specifica-
be regarded separately as standard. The values stated in each
tion or by mutual agreement by all interested parties.
system may not be exact equivalents; therefore, each system
must be used independently without combining values in any
4. Significance and Use
way.
4.1 This practice does not necessarily provide direct simu-
1.4 This standard does not purport to address all of the
lation of natural weathering exposure.
safety concerns, if any, associated with its use. It is the
4.2 Resultsfromuseofthispracticeshallnotberepresented
responsibility of the user of this standard to establish appro-
as being equivalent to those of any natural weathering test until
priate safety and health practices and determine the applica-
a satisfactory degree of correlation has been established for the
bility of regulatory limitations prior to use.
material in question.
2. Referenced Documents
4.3 Variations in results are possible when the operating
conditions vary within the accepted limits for the instrument
2.1 ASTM Standards:
specified in Practices G151 and G152.
A666 Specification forAnnealed or Cold-WorkedAustenitic
Stainless Steel Sheet, Strip, Plate, and Flat Bar
5. Apparatus
D3330/D3330M TestMethodforPeelAdhesionofPressure-
Sensitive Tape 5.1 Exposure Apparatus, conforming to the requirements
D3715/D3715M Practice for QualityAssurance of Pressure- defined in Practices G151 and G152 for exposure using the
Sensitive Tapes open-flame carbon arc with daylight filters.
D6551/D6551M Practice for Accelerated Weathering of
5.2 Panels, for holding or supporting the specimens ap-
proximately 75 by 225 mm [3 by 9 in.] and rigid enough to
resist deforming during use.
This practice is under the jurisdiction ofASTM Committee D10 on Packaging
5.2.1 ThematerialshallbeType302or304stainlesssteelin
and is the direct responsibility of Subcommittee D10.14 on Tape and Labels.
accordance with Specification A666 having a bright annealed
Current edition approved Aug. 1, 2011. Published November 2011. Originally
finish. The surface roughness height shall be 50 6 5 mm [2.0
approved in 1979. Last previous edition approved in 2005 as D3815/D3815M – 05.
DOI: 10.1520/D3815_D3815M-05R11.
6 0.1 µ-in.] arithmetical average deviation from the mean line.
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
5.2.2 Other dimensions or materials and finishes are accept-
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
able when defined by the subsequent test standard or commod-
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. ity specification.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
D3815/D3815M − 05 (2011)
5.2.3 A panel or frame of the dimensions required by the 8.1.1 When a test, such as in Test Method D3330/D3330M,
exposure apparatus may be used to support the specimen panel is to follow this exposure, it is customary to apply the tape to
when it is more convenient to do so, as long as the light and the prescribed panel in accordance with Test Method D3330/
water paths are not interrupted or shortened by doing so. D3330M preparatory
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D4169-23e1(Practice)
Standard Practice for Performance Testing of Shipping Containers and Systems

SIGNIFICANCE AND USE
4.1 This practice provides a guide for the evaluation of shipping units in accordance with a uniform system, using established test methods at levels representative of those occurring in actual distribution. The recommended test levels are based on available information on the shipping and handling environment, and current industry/government practice and experience (1-13).6 The tests should be performed sequentially on the same containers in the order given. For use as a performance test, this practice requires that the shipping unit tested remain unopened until the sequence of tests are completed. If used for other purposes, such as package development, it may be useful to open and inspect shipping units at various times throughout the sequence. This may, however, prohibit evaluating the influence of the container closure on container performance.  
4.2 For Distribution Cycle 18, as referred to in MIL-STD-2073–1, the use of this practice is defined in subsequent sections identified as DC-18.
SCOPE
1.1 This practice provides a uniform basis of evaluating, in a laboratory, the ability of shipping units to withstand the distribution environment. This is accomplished by subjecting them to a test plan consisting of a sequence of anticipated hazard elements encountered in various distribution cycles. This practice is not intended to supplant material specifications or existing preshipment test procedures.  
1.2 Consider the use of Practice D7386 for testing of packages for single parcel shipments.  
1.3 The suitability of this practice for use with hazardous materials has not been determined.  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    20 pages
    English language
    sale 15% off
ASTM
ASTM D999-08(2023)(Test Method)
Standard Test Methods for Vibration Testing of Shipping Containers

SIGNIFICANCE AND USE
4.1 Shipping containers are exposed to complex dynamic stresses when subjected to vibration present in all transportation vehicles. Approximating the actual damage, or lack of damage, experienced in shipping may require subjecting the container(s) and contents to vibration inputs.  
4.2 Resonant responses during shipment can be severe and may lead to package or product failure. Identification of critical frequencies, and the nature of package stresses can aid in minimizing the effect of these occurrences.  
4.3 Vibration tests should be based on representative field data. When possible, the confidence level may be improved by comparing laboratory test results with actual field shipment data. It is highly recommended that one understand the most common failures to one’s products and packaging in distribution, and then attempt to replicate those failures in the laboratory. Once such replication is established, then that test can become the minimum necessary test for future packaged products to pass.  
4.4 Exposure to vibration can affect the shipping container, its interior packaging, means of closure, and contents. These tests allow analysis of the interaction of these components. Design modification to one or more of these components may be utilized to achieve optimum performance in the shipping environment.  
4.5 Methods A1 and A2, Repetitive Shock Tests,  are suitable for tests of individual containers that are transported unrestrained on the bed of a vehicle and may be suitable for tests of containers that might be subjected to repetitive shocks due to magnification of vibrations in unit loads or stacks.
Note 1: Methods A1 and A2 produce different vibration motions, and therefore, will generate different forces which may result in different damage modes and intensities. Results from these two methods may not correlate with one another.  
4.6 Method B, Single Container Resonance Test,  tests or determines the ability of an individual container and its inter...
SCOPE
1.1 These test methods cover vibration tests of filled shipping containers. Such tests may be used to assess the performance of a container, with its interior packing and means of closure, both in terms of its strength and of the protection it provides its contents when it is subjected to vibration such as it experiences in transportation. These procedures are suitable for testing containers of any form, material, kind, design of interior packing, means of closure, and any size and weight. They are not intended for determining the response of products to vibration for product design purposes, nor are they intended for tests of products in their operational configuration as other more suitable procedures are available for these purposes.2,3  
1.2 The following methods appear:
Method A1—Repetitive Shock Test (Vertical Motion).
Method A2—Repetitive Shock Test (Rotary Motion).
Method B—Single Container Resonance Test.
Method C—Palletized Load, Unitized Load, or Vertical
Stack Resonance Test.  
1.3 For testing of intermediate bulk containers (IBCs) containing liquid hazardous materials, refer to Test Method D7387.  
1.4 These test methods fulfill the requirements of International Organization for Standardization standards ISO 8318 and ISO 2247. The ISO standards may not meet the requirements for these methods.  
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.6  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 6.  
1.7 This internatio...

  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM D1596-14(2023)(Test Method)
Standard Test Method for Dynamic Shock Cushioning Characteristics of Packaging Material

SIGNIFICANCE AND USE
5.1 Dynamic cushioning test data obtained by this test method are applicable to the cushioning material and not necessarily the same as obtained in a package. In addition to the influence of the package, the data can also be affected by the specimen area, thickness, loading rate, and other factors.
SCOPE
1.1 This test method covers a procedure for obtaining dynamic shock cushioning characteristics of packaging materials through acceleration-time data achieved from dropping a falling guided platen assembly onto a motionless sample. This test method does not address any effects or contributions of exterior packaging assemblies.  
1.2 The data acquired may be used for a single point or for use in developing a dynamic cushion curve for the specific material being tested. Such data may be used for comparison among different materials at specific input conditions, or qualifying materials against performance specifications. Caution should be used when attempting to compare data from different methods or when using such data for predicting in-package performance. Depending upon the particular materials of concern, correlation of such data (from among differing procedures or for predicting in–package performance) may be highly variable.
Note 1: Alternative and related method for possible consideration is Test Method D4168.  
1.3 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D3332-99(2023)(Test Method)
Standard Test Methods for Mechanical-Shock Fragility of Products, Using Shock Machines

SIGNIFICANCE AND USE
4.1 These test methods are intended to provide the user with data on product shock fragility that can be used in choosing optimum-cushioning materials for shipping containers or for product design modification.
SCOPE
1.1 These test methods cover determination of the shock fragility of products. This fragility information may be used in designing shipping containers for transporting the products. It may also be used to improve product ruggedness. Unit or consumer packages, which are transported within an outer container, are considered to be the product for the purposes of these test methods. Two test methods are outlined, as follows:  
1.1.1 Test Method A is used first, to determine the product's critical velocity change.  
1.1.2 Test Method B is used second, to determine the product's critical acceleration.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements, see Section 6.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    8 pages
    English language
    sale 15% off
ASTM
ASTM D7932-17(2023)(Specification)
Standard Specification for Printed, Pressure-Sensitive Adhesive Labels for Use in Extreme Distribution Environments

ABSTRACT
This specification provides a standard means for testing and measuring the performance characteristics of printed, pressure-sensitive adhesive labels for containers, particularly containers to be used in extreme distribution environments (for example, hazardous materials labels, aerospace, military containers). For the purposes of this specification, an extreme distribution environment is one in which it can be reasonably expected to experience direct exposure to deteriorating chemicals, weather, elevated/cold temperatures, and other environmental and physical elements for an extended period of time. This specification includes standard laboratory test methods to simulate exposure to various conditions and measure associated degradation of required performance characteristics. The data from these methods can be used as acceptance criteria between a supplier and customer. This specification covers the physical properties of the labels, as well as workmanship, finish and appearance, acceptance criteria, testing procedures, reporting of all the steps taken, certification, and preparation for delivery.
SCOPE
1.1 This specification provides a standard means to test and measure performance characteristics of printed, pressure-sensitive adhesive labels for containers, particularly containers to be used in extreme distribution environments (for example, hazardous materials labels, aerospace, military containers). For the purposes of this specification, an extreme distribution environment is one in which it can be reasonably expected to experience direct exposure to deteriorating chemicals, weather, elevated/cold temperatures, and other environmental and physical elements for an extended period of time.  
1.2 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    8 pages
    English language
    sale 15% off
ASTM
ASTM D4577-19(2023)(Test Method)
Standard Test Method for Compression Resistance of a Container Under Constant Load

SIGNIFICANCE AND USE
4.1 In the distribution system for many products there is a phase wherein the packaged product may be stored for a period of time in a manner such that one or more containers are superimposed one upon the other. Failure can occur in any layer4 (see Fig. 1 and Fig. 3).
FIG. 1 Containers Under Constant Load of Dead Weights Imposed by Other Containers
FIG. 2 Container Under Constant Load of Dead Weights
FIG. 3 Containers Under Constant Load in Compression Test Machine With Fixed Platen  
4.2 This test method subjects a container, empty or filled, to a predetermined static load, and to specified atmospheric conditions, if required.
SCOPE
1.1 This test method is designed to determine the resistance of a shipping container to a vertically applied constant load for either a specified time or to failure. The test method may also be used for palletized or unitized load configurations.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements, see Section 6.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    8 pages
    English language
    sale 15% off
ASTM
ASTM D3950-23(Specification)
Standard Specification for Strapping, Nonmetallic (and Joining Methods)

ABSTRACT
This specification covers nonmetallic strapping and joining methods for closing, reinforcing, and bundling materials for shipment, unitizing, palletizing, and bracing for car and truck loading. The strappings are classified into five types according to the type of materials used. If necessary, seals and buckles made from steel with zinc, black iron oxide, or any equivalent corrosion protective coatings or plastic buckles may be used. Each sample should be collected and tested using the given procedures and should conform to the required values of breaking strength and elongation, transverse strength, and joint strength, when applicable, for each strapping type.
SCOPE
1.1 This specification covers nonmetallic strapping and joining methods intended for use in closing, reinforcing, and bundling articles for shipment, unitizing, palletizing, and bracing for car loading and truck loading.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following safety hazards caveat pertains only to the test method portion, Section 12, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    9 pages
    English language
    sale 15% off
  • Technical specification
    9 pages
    English language
    sale 15% off
ASTM
ASTM D8410-22(Specification)
Standard Specification for Evaluation of Cellulosic-Fiber-Based Packaging Materials and Products for Compostability in Municipal or Industrial Aerobic Composting Facilities

SCOPE
1.1 This specification covers cellulosic-fiber-based packaging materials and products associated with food, landscape waste, and other compost feedstocks, which are intended to be composted under aerobic conditions in municipal and industrial composting facilities, where thermophilic temperatures are achieved.  
1.2 This specification covers cellulosic-based uncoated and coated packaging materials and products and covers whole packaging products. Products covered in this specification include cellulosic fiber-based products produced from cellulosic pulp, corrugated materials, containerboard, paper, paperboard, and molded fiber.  
1.3 This specification excludes end items where thermoplastic polymer is laminated or extruded to cellulosic substrates.  
1.4 This specification is intended to establish the requirements for labeling cellulosic-fiber-based packaging materials and products as “compostable in aerobic municipal and industrial composting facilities” in accordance with the guidelines issued by the Federal Trade Commission,2 provided the label includes proper qualifications as to the availability of such facilities.  
1.5 The properties in this specification are those required to determine if packaging materials and products will compost satisfactorily in large-scale aerobic municipal or industrial composting where maximum throughput is a high priority and where intermediate stages of biodegradation must not be apparent to the end user for aesthetic reasons.  
1.6 This specification is technically equivalent to ISO 18606.1.7.  
1.7 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM D4675-14a(2022)(Guide)
Standard Guide for Selection and Use of Flat Strapping Materials1

SIGNIFICANCE AND USE
4.1 This guide is intended to assist the user in selecting strapping material(s) and application method(s) for evaluation when subjected to handling, transit, and storage tests. It describes general load, unit and package types, strapping properties, strapping performance, weight considerations, shear planes, component frictional characteristics, and geometry.
SCOPE
1.1 This guide1 covers information on flat strapping materials (steel and nonmetallic) for the prospective user wanting initial guidance in selecting a strapping material and information on suggested application methods for use in packaging (closing, reinforcing, baling, bundling, unitizing, or palletizing), and loading applications (load unitization and securement to transport vehicle). The use applies to handling, securement, storage, and distribution systems.  
1.2 Carrier associations have established certain packaging and loading requirements that (in some cases) specify the type of strap, the minimum size or strength, the type of joint or seal, and the number of straps, seals, and joints that must be used for particular types of shipments or under certain conditions. Users should consult with their carriers initially to determine if there are applicable published requirements. Individual carriers may establish their own requirements. (See 2.2.)  
1.3 Limitations—This guide is not intended to give specific information as to how strapping must be used in any particular packaging or loading situation. Rather, it is intended to be informational in nature and is offered as a starting point for the testing of strapping being considered by the user. Thorough user testing is essential, as is a review of pertinent regulations that can influence strap selection (size and type), and application methods.  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    20 pages
    English language
    sale 15% off
ASTM
ASTM D4279-95(2022)(Test Method)
Standard Test Methods for Water Vapor Transmission of Shipping Containers—Constant and Cycle Methods

SIGNIFICANCE AND USE
4.1 These test methods are normally used for the following purposes:  
4.1.1 To evaluate materials and constructions for a specific type of container,  
4.1.2 To compare performance of different types of containers,  
4.1.3 To determine adequacy of protection for a specific product or application, and  
4.1.4 To maintain quality control.
SCOPE
1.1 These test methods cover the determination of water vapor transmission rates for bulk shipping containers, as follows:  
1.1.1 Method A, for Reclosable Containers, and  
1.1.2 Method B, for Containers Not Designed for Reclosing.  
1.2 Within each procedure details are given for the constant and cycle methods of test atmosphere.  
1.3 The test may be applied to the container as packed, or after one or more performance tests such as drum (Method D782), vibration (Methods D999), drop (Test Method D5276), impact resistance (Test Methods D880, D4003, and D5277), or performance tests (Practice D4169), as required.  
1.4 For small shipping containers requiring greater accuracy in weighing, the water vapor transmission may be determined in accordance with Test Method D895 or Test Method D1251.  
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off