Standard Specification for Hydrocarbon Unleaded Aviation Gasoline

SCOPE
1.1 This specification covers formulating specifications for purchases of aviation gasoline under contract and is intended primarily for use by purchasing agencies.  
1.2 Unleaded aviation gasoline defined by this specification is for use in engines and associated aircraft that are specifically approved by the engine and aircraft manufacturers. This fuel is not considered suitable for use in other engines and associated aircraft that are certified to use only leaded aviation gasolines of the same octane grade.  
1.3 This specification, unless otherwise provided, prescribes the required properties of unleaded aviation gasoline at the time and place of delivery.  
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

Status
Historical
Publication Date
30-Apr-2017
Current Stage
Ref Project

Relations

Buy Standard

Technical specification
ASTM D7547-17 - Standard Specification for Hydrocarbon Unleaded Aviation Gasoline
English language
7 pages
sale 15% off
Preview
sale 15% off
Preview
Technical specification
REDLINE ASTM D7547-17 - Standard Specification for Hydrocarbon Unleaded Aviation Gasoline
English language
7 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:D7547 −17 An American National Standard
Standard Specification for
1
Hydrocarbon Unleaded Aviation Gasoline
This standard is issued under the fixed designation D7547; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* D130 Test Method for Corrosiveness to Copper from Petro-
leum Products by Copper Strip Test
1.1 This specification covers formulating specifications for
D323 TestMethodforVaporPressureofPetroleumProducts
purchases of aviation gasoline under contract and is intended
(Reid Method)
primarily for use by purchasing agencies.
D873 Test Method for Oxidation Stability of Aviation Fuels
1.2 Unleaded aviation gasoline defined by this specification
(Potential Residue Method)
is for use in engines and associated aircraft that are specifically
D1094 Test Method for Water Reaction of Aviation Fuels
approved by the engine and aircraft manufacturers.This fuel is
D1298 Test Method for Density, Relative Density, or API
not considered suitable for use in other engines and associated
Gravity of Crude Petroleum and Liquid Petroleum Prod-
aircraft that are certified to use only leaded aviation gasolines
ucts by Hydrometer Method
of the same octane grade.
D2386 Test Method for Freezing Point of Aviation Fuels
1.3 Thisspecification,unlessotherwiseprovided,prescribes
D2622 Test Method for Sulfur in Petroleum Products by
the required properties of unleaded aviation gasoline at the
Wavelength Dispersive X-ray Fluorescence Spectrometry
time and place of delivery.
D2624 Test Methods for Electrical Conductivity ofAviation
1.4 The values stated in SI units are to be regarded as
and Distillate Fuels
standard. No other units of measurement are included in this
D2700 Test Method for Motor Octane Number of Spark-
standard.
Ignition Engine Fuel
D3237 TestMethodforLeadinGasolinebyAtomicAbsorp-
1.5 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the tion Spectroscopy
responsibility of the user of this standard to establish appro- D3338 Test Method for Estimation of Net Heat of Combus-
priate safety and health practices and determine the applica- tion of Aviation Fuels
bility of regulatory limitations prior to use. D4052 Test Method for Density, Relative Density, and API
1.6 This international standard was developed in accor-
Gravity of Liquids by Digital Density Meter
dance with internationally recognized principles on standard-
D4057 Practice for Manual Sampling of Petroleum and
ization established in the Decision on Principles for the
Petroleum Products
Development of International Standards, Guides and Recom-
D4171 Specification for Fuel System Icing Inhibitors
mendations issued by the World Trade Organization Technical
D4177 Practice for Automatic Sampling of Petroleum and
Barriers to Trade (TBT) Committee.
Petroleum Products
D4306 Practice for Aviation Fuel Sample Containers for
2. Referenced Documents
Tests Affected by Trace Contamination
2
2.1 ASTM Standards:
D4529 Test Method for Estimation of Net Heat of Combus-
D86 Test Method for Distillation of Petroleum Products and
tion of Aviation Fuels
Liquid Fuels at Atmospheric Pressure
D4809 Test Method for Heat of Combustion of Liquid
Hydrocarbon Fuels by Bomb Calorimeter (Precision
Method)
1
This specification is under the jurisdiction of ASTM Committee D02 on
D4865 Guide for Generation and Dissipation of Static Elec-
Petroleum Products, Liquid Fuels, and Lubricants and is the direct responsibility of
Subcommittee D02.J0.02 on Spark and Compression Ignition Aviation Engine
tricity in Petroleum Fuel Systems
Fuels.
D5006 Test Method for Measurement of Fuel System Icing
CurrenteditionapprovedMay1,2017.PublishedJuly2017.Originallyapproved
ɛ1
Inhibitors (Ether Type) in Aviation Fuels
in 2009. Last previous edition approved in 2015 as D7547 – 15 . DOI: 10.1520/
D7547-17.
D5059 Test Methods for Lead in Gasoline by X-Ray Spec-
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
troscopy
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
D5191 Test Method for Vapor Pressure of Petroleum Prod-
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. ucts (Mini Method)
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D7547−17
D6469 GuideforMicrobialContaminationinFuelsandFuel 5.2.2.1 Isopropyl Alcohol (IPA, propan-2-ol), in accordance
S
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
´1
Designation: D7547 − 15 D7547 − 17 An American National Standard
Standard Specification for
1
Hydrocarbon Unleaded Aviation Gasoline
This standard is issued under the fixed designation D7547; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1
ε NOTE—Title of Table 1 was corrected editorially in December 2016.
1. Scope*
1.1 This specification covers formulating specifications for purchases of aviation gasoline under contract and is intended
primarily for use by purchasing agencies.
1.2 Unleaded aviation gasoline defined by this specification is for use in engines and associated aircraft that are specifically
approved by the engine and aircraft manufacturers. This fuel is not considered suitable for use in other engines and associated
aircraft that are certified to use only leaded aviation gasolines of the same octane grade.
1.3 This specification, unless otherwise provided, prescribes the required properties of unleaded aviation gasoline at the time
and place of delivery.
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
D86 Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure
D130 Test Method for Corrosiveness to Copper from Petroleum Products by Copper Strip Test
D323 Test Method for Vapor Pressure of Petroleum Products (Reid Method)
D873 Test Method for Oxidation Stability of Aviation Fuels (Potential Residue Method)
D1094 Test Method for Water Reaction of Aviation Fuels
D1298 Test Method for Density, Relative Density, or API Gravity of Crude Petroleum and Liquid Petroleum Products by
Hydrometer Method
D2386 Test Method for Freezing Point of Aviation Fuels
D2622 Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
D2624 Test Methods for Electrical Conductivity of Aviation and Distillate Fuels
D2700 Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
D3237 Test Method for Lead in Gasoline by Atomic Absorption Spectroscopy
D3338 Test Method for Estimation of Net Heat of Combustion of Aviation Fuels
D4052 Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter
D4057 Practice for Manual Sampling of Petroleum and Petroleum Products
D4171 Specification for Fuel System Icing Inhibitors
D4177 Practice for Automatic Sampling of Petroleum and Petroleum Products
D4306 Practice for Aviation Fuel Sample Containers for Tests Affected by Trace Contamination
1
This specification is under the jurisdiction of ASTM Committee D02 on Petroleum Products, Liquid Fuels, and Lubricants and is the direct responsibility of Subcommittee
D02.J0.02 on Spark and Compression Ignition Aviation Engine Fuels.
Current edition approved Nov. 1, 2015May 1, 2017. Published November 2015July 2017. Originally approved in 2009. Last previous edition approved in 20142015 as
ɛ1
D7547 – 14b.D7547 – 15 . DOI: 10.1520/D7547-15E01.10.1520/D7547-17.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D7547 − 17
D4529 Test Method for Estimation of Net Heat of Combustion of Aviation Fuels
D4809 Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter (Precision Method)
D48
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.