iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D4000-00a

(Classification)

Standard Classification System for Specifying Plastic Materials

Standard Classification System for Specifying Plastic Materials

SCOPE
1.1 This standard provides a classification system for tabulating the properties of unfilled, filled, and reinforced plastic materials suitable for processing into parts.
Note 1—The classification system may serve many of the needs of industries using plastic materials. The standard is subject to revision as the need requires; therefore, the latest revision should always be used.
1.2 The classification system and subsequent line callout (specification) is intended to be a means of identifying plastic materials used in the fabrication of end items or parts. It is not intended for the selection of materials. Material selection should be made by those having expertise in the plastics field after careful consideration of the design and the performance required of the part, the environment to which it will be exposed, the fabrication process to be employed, the inherent properties of the material not covered in this document, and the economic factors.
1.3 This classification system is based on the premise that plastic materials can be arranged into broad generic families using basic properties to arrange the materials into groups, classes, and grades. A system is thus established which, together with values describing additional requirements, permits as complete a description as desired of the selected material.
1.4 In all cases where the provisions of this classification system would conflict with the referenced ASTM specification for a particular material, the latter shall take precedence. Note 2—When using this classification system the two-letter, three-digit suffix system applies.Note 3—When a material is used to fabricate a part where the requirements are too specific for a broad material callout, it is advisable for the user to consult the supplier to secure callout of the properties to suit the actual conditions to which the part is to be subjected.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
09-Dec-2001
ICS
01.040.83 - Rubber and plastics industries (Vocabularies)
83.080.01 - Plastics in general
Technical Committee
D20 - Plastics
Current Stage
Ref Project

Relations

Replaces
ASTM D4000-00 - Standard Classification System for Specifying Plastic Materials
Effective Date
10-Dec-2001
Replaced By
ASTM D4000-01 - Standard Classification System for Specifying Plastic Materials
Effective Date
10-Dec-2001
Referred By
ASTM D4067-23 - Standard Classification System and Basis for Specification for Reinforced and Filled Poly(Phenylene Sulfide) (PPS) Injection Molding and Extrusion Materials Using ASTM Methods
Effective Date
10-Dec-2001
Referred By
ASTM D2990-17 - Standard Test Methods for Tensile, Compressive, and Flexural Creep and Creep-Rupture of Plastics
Effective Date
10-Dec-2001
Referred By
ASTM D6712-17 - Standard Specification for Ultra-High-Molecular-Weight Polyethylene (UHMW-PE) Solid Plastic Shapes
Effective Date
10-Dec-2001
Referred By
ASTM D6112-18 - Standard Test Methods for Compressive and Flexural Creep and Creep-Rupture of Plastic Lumber and Shapes
Effective Date
10-Dec-2001
Referred By
ASTM D785-23 - Standard Test Method for Rockwell Hardness of Plastics and Electrical Insulating Materials
Effective Date
10-Dec-2001
Referred By
ASTM D1004-21 - Standard Test Method for Tear Resistance (Graves Tear) of Plastic Film and Sheeting
Effective Date
10-Dec-2001
Referred By
ASTM D1043-16 - Standard Test Method for Stiffness Properties of Plastics as a Function of Temperature by Means of a Torsion Test
Effective Date
10-Dec-2001
Referred By
ASTM D695-23 - Standard Test Method for Compressive Properties of Rigid Plastics
Effective Date
10-Dec-2001
Referred By
ASTM D6693/D6693M-20 - Standard Test Method for Determining Tensile Properties of Nonreinforced Polyethylene and Nonreinforced Flexible Polypropylene Geomembranes
Effective Date
10-Dec-2001
Referred By
ASTM D6098-16 - Standard Classification System and Basis for Specification for Extruded and Compression Molded Shapes Made from Polycarbonate (PC)
Effective Date
10-Dec-2001
Referred By
ASTM D4976-12a(2020) - Standard Specification for Polyethylene Plastics Molding and Extrusion Materials
Effective Date
10-Dec-2001
Referred By
ASTM D4440-15 - Standard Test Method for Plastics: Dynamic Mechanical Properties Melt Rheology
Effective Date
10-Dec-2001
Referred By
ASTM D5023-15 - Standard Test Method for Plastics: Dynamic Mechanical Properties: In Flexure (Three-Point Bending)
Effective Date
10-Dec-2001

Buy Standard

ASTM D4000-00a - Standard Classification System for Specifying Plastic MaterialsASTM D4000-00a - Standard Classification System for Specifying Plastic Materials
PreviousNext
Standard
ASTM D4000-00a - Standard Classification System for Specifying Plastic Materials
English language
18 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
Designation: D 4000 – 00a An American National Standard
Standard Classification System for
1
Specifying Plastic Materials
This standard is issued under the fixed designation D 4000; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope * 2. Referenced Documents
1.1 This standard provides a classification system for tabu- 2.1 ASTM Standards:
lating the properties of unfilled, filled, and reinforced plastic D 149 Test Method for Dielectric Breakdown Voltage and
materials suitable for processing into parts. Dielectric Strength of Solid Electrical Insulating Materials
2
at Commercial Power Frequencies
NOTE 1—The classification system may serve many of the needs of
D 150 Test Methods for A-C Loss Characteristics and
industries using plastic materials. The standard is subject to revision as the
Permittivity (Dielectric Constant) of Solid Electrical Insu-
need requires; therefore, the latest revision should always be used.
2
lating Materials
1.2 The classification system and subsequent line callout
D 256 Test Method for Determining the Izod Pendulum
(specification) is intended to be a means of identifying plastic
3
Impact Resistance of Notched Specimens of Plastics
materials used in the fabrication of end items or parts. It is not
D 257 Test Methods for D-C Resistance or Conductance of
intended for the selection of materials. Material selection
2
Insulating Materials
should be made by those having expertise in the plastics field
D 395 Test Methods for Rubber Property—Compression
after careful consideration of the design and the performance
4
Set
required of the part, the environment to which it will be
D 412 Test Methods for Vulcanized Rubber and Thermo-
exposed, the fabrication process to be employed, the inherent
4
plastic Rubbers and Thermoplastic Elastomers—Tension
properties of the material not covered in this document, and the
D 471 Test Method for Rubber Property—Effect of Liq-
economic factors.
4
uids
1.3 This classification system is based on the premise that
D 495 Test Method for High-Voltage, Low-Current, Dry
plastic materials can be arranged into broad generic families
2
Arc Resistance of Solid Electrical Insulation
using basic properties to arrange the materials into groups,
D 569 Method for Measuring the Flow Properties of Ther-
classes, and grades. A system is thus established which,
5
moplastic Molding Materials
together with values describing additional requirements, per-
3
D 570 Test Method for Water Absorption of Plastics
mits as complete a description as desired of the selected
D 573 Test Method for Rubber—Deterioration in an Air
material.
4
Oven
1.4 In all cases where the provisions of this classification
4
D 575 Test Methods for Rubber Properties in Compression
system would conflict with the referenced ASTM specification
D 618 Practice for Conditioning Plastics and Electrical
for a particular material, the latter shall take precedence.
3
Insulating Materials for Testing
NOTE 2—When using this classification system the two-letter, three-
D 624 Test Method for Tear Strength of Conventional
4
digit suffix system applies.
Vulcanized Rubber and Thermoplastic Elastomers
NOTE 3—When a material is used to fabricate a part where the
D 635 Test Method for Rate of Burning and/or Extent and
requirements are too specific for a broad material callout, it is advisable
Time of Burning of Self-Supporting Plastics in a Horizon-
for the user to consult the supplier to secure callout of the properties to suit
3
tal Position
the actual conditions to which the part is to be subjected.
3
D 638 Test Method for Tensile Properties of Plastics
1.5 This standard does not purport to address all of the
D 648 Test Method for Deflection Temperature of Plastics
safety concerns, if any, associated with its use. It is the
3
Under Flexural Load
responsibility of the user of this standard to establish appro-
D 695 Test Method for Compressive Properties of Rigid
priate safety and health practices and determine the applica-
3
Plastics
bility of regulatory limitations prior to use.
D 706 Specification for Cellulose Acetate Molding and
1
This classification system is under the jurisdiction of ASTM Committee D20 on
2
Plastics and is the direct responsibility of Subcommittee D20.94 on Government/ Annual Book of ASTM Standards, Vol 10.01.
3
Industry Standardization (Section D20.94.01). Annual Book of ASTM Standards, Vol 08.01.
4
Current edition approved Dec. 10, 2000. Published March 2001. Originally Annual Book of ASTM Standards, Vol 09.01.
5
published as
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D883-23(Terminology)
Standard Terminology Relating to Plastics

SCOPE
1.1 This terminology covers definitions of technical terms used in the plastics industry. Terms that are generally understood or adequately defined in other readily available sources are not included.  
1.2 When a term is used in an ASTM document for which Committee D20 is responsible it is included only when judged, after review, by Subcommittee D20.92 to be a generally usable term.  
1.3 Definitions that are identical to those published by another standards body are identified with the abbreviation of the name of the organization; for example, IUPAC is the International Union of Pure and Applied Chemistry.  
1.4 A definition is a single sentence with additional information included in discussion notes.
Note 1: It is recommended that definitions be reviewed periodically.  
1.4.1 When a new definition is added to this terminology standard, or the wording of a definition is revised, the date of the change shall be appended to the new or revised definition.  
1.5 For literature related to plastics terminology, see Appendix X1.  
1.6 Subsections 1.6.1 – 1.6.5 contain references to specific terminology standards that are relevant to specific plastic products or applications. In case of conflict between a definition contained in Terminology D883 and one contained in another standard, the definition given in Terminology D883 shall prevail.  
1.6.1 For terms related to thermal insulation, the applicable definitions are contained in Terminology C168.  
1.6.2 For terms related to electrical or electronic insulating materials, the applicable definitions are contained in Terminology D1711.  
1.6.3 For terms relating to fire, the applicable definitions are contained in Terminology E176 and ISO 13943. In case of conflict between Terminology E176 and ISO 13943, the definitions given in Terminology E176 shall prevail.  
1.6.4 For terms relating to precision and bias and associated issues, the applicable definitions are contained in Terminology E456.  
1.6.5 For terms related to plastic piping systems, the applicable definitions are contained in Terminology F412.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    18 pages
    English language
    sale 15% off
  • Standard
    18 pages
    English language
    sale 15% off
ASTM
ASTM D4000-23(Classification)
Standard Classification System for Specifying Plastic Materials

SIGNIFICANCE AND USE
4.1 The purpose of this classification system is to provide a method of adequately identifying plastic materials in order to give industry a system that can be used universally for plastic materials. It further provides a means for specifying these materials by the use of a simple line call-out designation.  
4.2 This classification system was developed to permit the addition of property values for future plastics.
SCOPE
1.1 This standard provides a classification system for tabulating the properties of unfilled, filled, and reinforced plastic materials suitable for processing into parts.
Note 1: The classification system serves many of the needs of industries using plastic materials. The standard is subject to revision as the need requires; therefore, the latest revision should always be used.  
1.2 The classification system and subsequent line call-out (specification) is intended to be a means of identifying plastic materials used in the fabrication of end items or parts. It is not intended for the selection of materials. Material selection should be made by those having expertise in the plastics field after careful consideration of the design and the performance required of the part, the environment to which it will be exposed, the fabrication process to be employed, the inherent properties of the material not covered in this document, and the economic factors.  
1.3 This classification system is based on the premise that plastic materials can be arranged into broad generic families using basic properties to arrange the materials into groups, classes, and grades. A system is thus established which, together with values describing additional requirements, permits as complete a description as desired of the selected material.  
1.4 In all cases where the provisions of this classification system would conflict with the referenced ASTM specification for a particular material, the latter shall take precedence.  
Note 2: When using this classification system the two-letter, three-digit suffix system applies.
Note 3: When a material is used to fabricate a part where the requirements are too specific for a broad material call-out, it is advisable for the user to consult the supplier to secure a call-out of the properties to suit the actual conditions to which the part is to be subjected.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    22 pages
    English language
    sale 15% off
  • Standard
    22 pages
    English language
    sale 15% off
ASTM
ASTM D4092-21(Terminology)
Standard Terminology for Plastics: Dynamic Mechanical Properties

SCOPE
1.1 This terminology is a compilation of definitions and descriptions of technical terms used in dynamic mechanical property measurements on polymeric materials, including solutions, melts, and solids. Terms that are generally understood or defined adequately in other readily available sources are either not included or sources identified.  
1.2 A definition is a single sentence with additional information included in notes. It is reviewed every five years and the year of the last review or revision is appended.  
1.3 Definitions identical to those published by another standards organization or ASTM committee are identified with the abbreviation of the name of the organization or the ASTM committee.  
1.4 Descriptions of terms specific to dynamic mechanical measurements are identified with an italicized introductory phrase.  
Note 1: This terminology standard is similar to ISO 6721–1 however, the ISO document cites fewer terms.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D1600-18(Terminology)
Standard Terminology for Abbreviated Terms Relating to Plastics

SCOPE
1.1 The purpose of this terminology is to provide uniform contractions of terms relating to plastics. Abbreviated terminology has evolved through widespread common usage. This compilation has been prepared to avoid both the occurrence of more than one abbreviated term for a given plastics term and multiple meanings for abbreviated terms.  
1.2 The scope of these abbreviated terms includes plastics terms pertaining to composition and relating to type or kind according to mode of preparation or principle distinguishing characteristics. Also included are abbreviated terms for terms relating to copolymers, blends and alloys of plastics, and additives such as plasticizers, fillers, etc.  
Note 1: A code relating to the composition of rubbers is given in Practice D1418.  
1.3 No attempt is made here to systematize formally a shorthand terminology for polymers. Terminology, including nomenclature, codes, symbols, and formula designations for use in scientific literature in the field of natural and synthetic polymers, are being studied and standardized by the International Union of Pure and Applied Chemistry.2  
1.4 These abbreviated terms are by no means all-inclusive of plastics terminology. They represent, in general, those terms that have come into established use. Since it is recognized that abbreviated terms serve no useful purpose unless they are generally accepted and used, no attempt has been made to establish a rigorous code for devising standard abbreviated terms. This would result in awkward departures from established usage of existing and accepted abbreviated terms and lead to cumbersome combinations in the future, which would not be likely to receive widespread acceptance. The abbreviated terms now in use have grown naturally out of the need for convenient, readily comprehended shorthand for long chemical names. This process can be expected to continue along the natural lines of least resistance and will serve as a basis for further standardization as the need arises. A general guide for the preparation of abbreviated terms appears desirable, however, to facilitate more organized and uniform standardization in the future. An appendix is attached, which suggests a uniform way to prepare abbreviated terms.  
1.5 Note that the uppercase letter F should be used to designate phosphate and that other elements may also be designated F.  
1.6 An abbreviated term (FR) and code numbers are provided to identify classes of materials used as flame retardants added to plastics. The system is provided for use in situations where marking of plastics products is desired.  
Note 2: Many of the abbreviated terms, codes, numbers, and symbols in ISO 1043 parts 1 through 4 and in ISO/DIS 1043-4 are the same as the corresponding item in ASTM D1600. D1600 includes a number of abbreviated terms that are not in ISO 1043.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    11 pages
    English language
    sale 15% off
  • Standard
    11 pages
    English language
    sale 15% off
ASTM
ASTM D883-23(Terminology)
Standard Terminology Relating to Plastics

SCOPE
1.1 This terminology covers definitions of technical terms used in the plastics industry. Terms that are generally understood or adequately defined in other readily available sources are not included.  
1.2 When a term is used in an ASTM document for which Committee D20 is responsible it is included only when judged, after review, by Subcommittee D20.92 to be a generally usable term.  
1.3 Definitions that are identical to those published by another standards body are identified with the abbreviation of the name of the organization; for example, IUPAC is the International Union of Pure and Applied Chemistry.  
1.4 A definition is a single sentence with additional information included in discussion notes.
Note 1: It is recommended that definitions be reviewed periodically.  
1.4.1 When a new definition is added to this terminology standard, or the wording of a definition is revised, the date of the change shall be appended to the new or revised definition.  
1.5 For literature related to plastics terminology, see Appendix X1.  
1.6 Subsections 1.6.1 – 1.6.5 contain references to specific terminology standards that are relevant to specific plastic products or applications. In case of conflict between a definition contained in Terminology D883 and one contained in another standard, the definition given in Terminology D883 shall prevail.  
1.6.1 For terms related to thermal insulation, the applicable definitions are contained in Terminology C168.  
1.6.2 For terms related to electrical or electronic insulating materials, the applicable definitions are contained in Terminology D1711.  
1.6.3 For terms relating to fire, the applicable definitions are contained in Terminology E176 and ISO 13943. In case of conflict between Terminology E176 and ISO 13943, the definitions given in Terminology E176 shall prevail.  
1.6.4 For terms relating to precision and bias and associated issues, the applicable definitions are contained in Terminology E456.  
1.6.5 For terms related to plastic piping systems, the applicable definitions are contained in Terminology F412.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    18 pages
    English language
    sale 15% off
  • Standard
    18 pages
    English language
    sale 15% off
ASTM
ASTM D4000-23(Classification)
Standard Classification System for Specifying Plastic Materials

SIGNIFICANCE AND USE
4.1 The purpose of this classification system is to provide a method of adequately identifying plastic materials in order to give industry a system that can be used universally for plastic materials. It further provides a means for specifying these materials by the use of a simple line call-out designation.  
4.2 This classification system was developed to permit the addition of property values for future plastics.
SCOPE
1.1 This standard provides a classification system for tabulating the properties of unfilled, filled, and reinforced plastic materials suitable for processing into parts.
Note 1: The classification system serves many of the needs of industries using plastic materials. The standard is subject to revision as the need requires; therefore, the latest revision should always be used.  
1.2 The classification system and subsequent line call-out (specification) is intended to be a means of identifying plastic materials used in the fabrication of end items or parts. It is not intended for the selection of materials. Material selection should be made by those having expertise in the plastics field after careful consideration of the design and the performance required of the part, the environment to which it will be exposed, the fabrication process to be employed, the inherent properties of the material not covered in this document, and the economic factors.  
1.3 This classification system is based on the premise that plastic materials can be arranged into broad generic families using basic properties to arrange the materials into groups, classes, and grades. A system is thus established which, together with values describing additional requirements, permits as complete a description as desired of the selected material.  
1.4 In all cases where the provisions of this classification system would conflict with the referenced ASTM specification for a particular material, the latter shall take precedence.  
Note 2: When using this classification system the two-letter, three-digit suffix system applies.
Note 3: When a material is used to fabricate a part where the requirements are too specific for a broad material call-out, it is advisable for the user to consult the supplier to secure a call-out of the properties to suit the actual conditions to which the part is to be subjected.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    22 pages
    English language
    sale 15% off
  • Standard
    22 pages
    English language
    sale 15% off
ASTM
ASTM D4092-21(Terminology)
Standard Terminology for Plastics: Dynamic Mechanical Properties

SCOPE
1.1 This terminology is a compilation of definitions and descriptions of technical terms used in dynamic mechanical property measurements on polymeric materials, including solutions, melts, and solids. Terms that are generally understood or defined adequately in other readily available sources are either not included or sources identified.  
1.2 A definition is a single sentence with additional information included in notes. It is reviewed every five years and the year of the last review or revision is appended.  
1.3 Definitions identical to those published by another standards organization or ASTM committee are identified with the abbreviation of the name of the organization or the ASTM committee.  
1.4 Descriptions of terms specific to dynamic mechanical measurements are identified with an italicized introductory phrase.  
Note 1: This terminology standard is similar to ISO 6721–1 however, the ISO document cites fewer terms.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D1600-18(Terminology)
Standard Terminology for Abbreviated Terms Relating to Plastics

SCOPE
1.1 The purpose of this terminology is to provide uniform contractions of terms relating to plastics. Abbreviated terminology has evolved through widespread common usage. This compilation has been prepared to avoid both the occurrence of more than one abbreviated term for a given plastics term and multiple meanings for abbreviated terms.  
1.2 The scope of these abbreviated terms includes plastics terms pertaining to composition and relating to type or kind according to mode of preparation or principle distinguishing characteristics. Also included are abbreviated terms for terms relating to copolymers, blends and alloys of plastics, and additives such as plasticizers, fillers, etc.  
Note 1: A code relating to the composition of rubbers is given in Practice D1418.  
1.3 No attempt is made here to systematize formally a shorthand terminology for polymers. Terminology, including nomenclature, codes, symbols, and formula designations for use in scientific literature in the field of natural and synthetic polymers, are being studied and standardized by the International Union of Pure and Applied Chemistry.2  
1.4 These abbreviated terms are by no means all-inclusive of plastics terminology. They represent, in general, those terms that have come into established use. Since it is recognized that abbreviated terms serve no useful purpose unless they are generally accepted and used, no attempt has been made to establish a rigorous code for devising standard abbreviated terms. This would result in awkward departures from established usage of existing and accepted abbreviated terms and lead to cumbersome combinations in the future, which would not be likely to receive widespread acceptance. The abbreviated terms now in use have grown naturally out of the need for convenient, readily comprehended shorthand for long chemical names. This process can be expected to continue along the natural lines of least resistance and will serve as a basis for further standardization as the need arises. A general guide for the preparation of abbreviated terms appears desirable, however, to facilitate more organized and uniform standardization in the future. An appendix is attached, which suggests a uniform way to prepare abbreviated terms.  
1.5 Note that the uppercase letter F should be used to designate phosphate and that other elements may also be designated F.  
1.6 An abbreviated term (FR) and code numbers are provided to identify classes of materials used as flame retardants added to plastics. The system is provided for use in situations where marking of plastics products is desired.  
Note 2: Many of the abbreviated terms, codes, numbers, and symbols in ISO 1043 parts 1 through 4 and in ISO/DIS 1043-4 are the same as the corresponding item in ASTM D1600. D1600 includes a number of abbreviated terms that are not in ISO 1043.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    11 pages
    English language
    sale 15% off
  • Standard
    11 pages
    English language
    sale 15% off
ASTM
ASTM F1210-23(Guide)
Standard Guide for Ecological Considerations for the Use of Oil Spill Dispersants in Freshwater and Other Inland Environments, Lakes and Large Water Bodies

SIGNIFICANCE AND USE
3.1 This guide is meant to aid response teams who may use it during spill response planning and spill events.  
3.2 This guide should be adapted to site specific circumstance.
SCOPE
1.1 This guide covers the use of oil spill dispersants to assist in the control of oil spills. The guide is written with the goal of minimizing the environmental impacts of oil spills; this goal is the basis on which the recommendations are made. Aesthetic and socioeconomic factors are not considered, although these and other factors are often important in spill response.  
1.2 Spill responders have available several means to control or clean up spilled oil. Chemical dispersants should be given equal consideration with other spill countermeasures.  
1.3 This is a general guide only. Oil, as used in this guide, includes crude oils and refined petroleum products. Differences between individual dispersants or between different oil products are not considered. The dispersibility of the oil with the chosen dispersant should be evaluated.  
1.4 The guide is organized by habitat type, for example, small ponds and lakes, rivers and streams, and land. It considers the use of dispersants primarily to protect habitats from impact (or to minimize impacts).  
1.5 This guide applies only to freshwater and other inland environments. It does not consider the direct application of dispersants to subsurface waters.  
1.6 In making dispersant use decisions, appropriate government authorities should be consulted as required by law.  
1.7 This guide does not address getting regulatory approval.  
1.8 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    3 pages
    English language
    sale 15% off
  • Guide
    3 pages
    English language
    sale 15% off
ASTM
ASTM C596-23(Test Method)
Standard Test Method for Drying Shrinkage of Mortar Containing Hydraulic Cement

SIGNIFICANCE AND USE
4.1 This test method establishes a selected set of conditions of temperature, relative humidity and rate of evaporation of the environment to which a mortar specimen of stated composition shall be subjected for a specified period of time during which its change in length is determined and designated “drying shrinkage.”  
4.2 The drying shrinkage of mortar as determined by this test method has a linear relation to the drying shrinkage of concrete made with the same cement and exposed to the same drying conditions.4 Hence this test method may be used when it is desired to develop data on the effect of a hydraulic cement on the drying shrinkage of concrete made with that cement.
SCOPE
1.1 This test method determines the change in length on drying of mortar bars containing hydraulic cement and graded standard sand.  
1.2 The values stated in SI units are to be regarded as standard. When combined standards are referenced, the selection of measurement system is at the user’s discretion subject to the requirements of the referenced standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Warning—Fresh hydraulic cementitious mixtures are caustic and may cause chemical burns to skin and tissue upon prolonged exposure).2  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off