iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D3052-17

(Practice)

Standard Practice for Rating Water-Emulsion Floor Polishes

Standard Practice for Rating Water-Emulsion Floor Polishes

SIGNIFICANCE AND USE
3.1 When comparing different floor polishes for an actual field performance, it is important that all surfaces used be prepared in the same way. When this procedure is followed, variations in the test surfaces are minimized.
SCOPE
1.1 This practice covers the comparison of the performance of water-emulsion floor polishes on test floors against a reference material. It is applicable to the following types of polishes:  
1.1.1 Wax emulsion polishes,  
1.1.2 Nonbuffable emulsion polishes,  
1.1.3 Detergent-resistant emulsion polishes, household type, and  
1.1.4 Detergent-resistant emulsion polishes, industrial type.  
1.2 Gloss, leveling, discoloration, traffic marking, slip resistance, and removal ease of these types of floor polishes is rated in comparison to a reference material. Where applicable, detergent resistance is also evaluated. This method is not to be considered as a recommended maintenance procedure.  
1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

Status
Historical
Publication Date
28-Feb-2017
ICS
71.100.99 - Other products of the chemical industry
Technical Committee
D21 - Polishes
Drafting Committee
D21.04 - Performance Tests
Current Stage
Ref Project

Relations

Replaces
ASTM D3052-87(2010) - Standard Practice for Rating Water-Emulsion Floor Polishes
Effective Date
01-Mar-2017
Refers
ASTM D523-14 - Standard Test Method for Specular Gloss
Effective Date
01-Jan-2014
Refers
ASTM D523-08 - Standard Test Method for Specular Gloss
Effective Date
01-Jun-2008
Refers
ASTM D523-89(2008) - Standard Test Method for Specular Gloss
Effective Date
01-Feb-2008
Refers
ASTM D523-89(1999) - Standard Test Method for Specular Gloss
Effective Date
10-May-1999
Referred By
ASTM D4078-02(2021) - Standard Specification for Water Emulsion Floor Polish
Effective Date
01-Mar-2017
Referred By
ASTM D3440-13(2019) - Standard Guide for Preparing Specifications for Water-Emulsion Floor Polishes
Effective Date
01-Mar-2017

Buy Standard

ASTM D3052-17 - Standard Practice for Rating Water-Emulsion Floor PolishesASTM D3052-17 - Standard Practice for Rating Water-Emulsion Floor Polishes
PreviousNext
Standard
ASTM D3052-17 - Standard Practice for Rating Water-Emulsion Floor Polishes
English language
6 pages
sale 15% off
Preview
sale 15% off
Preview
REDLINE ASTM D3052-17 - Standard Practice for Rating Water-Emulsion Floor PolishesREDLINE ASTM D3052-17 - Standard Practice for Rating Water-Emulsion Floor Polishes
PreviousNext
Standard
REDLINE ASTM D3052-17 - Standard Practice for Rating Water-Emulsion Floor Polishes
English language
6 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: D3052 − 17
Standard Practice for
1
Rating Water-Emulsion Floor Polishes
This standard is issued under the fixed designation D3052; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 2. Referenced Documents
2
2.1 ASTM Standards:
1.1 This practice covers the comparison of the performance
D523Test Method for Specular Gloss
of water-emulsion floor polishes on test floors against a
2.2 CSMA Bulletin:
reference material. It is applicable to the following types of
245-70Comparative Determination of Slip Resistance of
polishes:
3
Floor Polishes
1.1.1 Wax emulsion polishes,
1.1.2 Nonbuffable emulsion polishes,
3. Significance and Use
1.1.3 Detergent-resistantemulsionpolishes,householdtype,
3.1 When comparing different floor polishes for an actual
and
field performance, it is important that all surfaces used be
1.1.4 Detergent-resistant emulsion polishes, industrial type. prepared in the same way. When this procedure is followed,
variations in the test surfaces are minimized.
1.2 Gloss, leveling, discoloration, traffic marking, slip
resistance, and removal ease of these types of floor polishes is
4. Apparatus
rated in comparison to a reference material. Where applicable,
4
4.1 Test Tile, OVCT.
detergent resistance is also evaluated. This method is not to be
4.2 Glossmeter, 60°—The instrument and the reference
considered as a recommended maintenance procedure.
standards shall conform to the requirements prescribed in Test
1.3 The values stated in inch-pound units are to be regarded
Method D523, using an angle of reflection of 60°.
as the standard. The values given in parentheses are for
4.3 Floor Machine.
information only.
5. Procedure
1.4 The values stated in inch-pound units are to be regarded
as standard. The values given in parentheses are mathematical 5.1 The preferred substrate shall be Official Vinyl Compo-
conversions to SI units that are provided for information only sition Tile.
and are not considered standard.
5.2 The test floor shall include both dark (black) and light
(white) colored tiles laid out so that one half of the panel is all
1.5 This standard does not purport to address all of the
white and the other half is all black.
safety concerns, if any, associated with its use. It is the
responsibility of the user of this standard to establish appro-
5.3 Theminimumtestpanelsizeforeachpolishtestedshall
priate safety and health practices and determine the applica- be 3 ft (0.9 m) in width and 3 ft in length.
bility of regulatory limitations prior to use.
5.4 Prepare all of the test panels with scrub-cleaned new
1.6 This international standard was developed in accor-
tiles, or strip completely of dirt and old wax, rinse thoroughly
dance with internationally recognized principles on standard-
and dry before application of the test polishes. Under no
ization established in the Decision on Principles for the
Development of International Standards, Guides and Recom-
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
mendations issued by the World Trade Organization Technical
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Barriers to Trade (TBT) Committee.
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.
3
Available from the Chemical Specialties Manufacturers Association, 1001
Connecticut Avenue, NW, Washington, DC 20036.
1 4
This practice is under the jurisdiction of ASTM Committee D21 on Polishes OVCT tile may be obtained through Armstrong Flooring from various home
and is the direct responsibility of Subcommittee D21.04 on Performance Tests. improvement stores. The following Armstrong tile substrates have been found to
Current edition approved March 1, 2017. Published April 2017. Originally perform adequately for this test method: Armstrong Excelon Feature Tile: Black
approved in 1972. Last previous edition approved in 2010 as D3052–87 (2010). (56790), http://www.armstrong.com/commflooringna/product_details_toolbox_
DOI: 10.1520/D3052-17. magnify.jsp?item_id=47394.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D3052 − 17
circumstancesshouldcomparativetestsbemadeonnewversus necessitate longer periods of drying time.) Again take gloss
old tiles. Similarly, where old tiles are employed, care should readings on the four
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D3052 − 87 (Reapproved 2010) D3052 − 17
Standard Practice for
1
Rating Water-Emulsion Floor Polishes
This standard is issued under the fixed designation D3052; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This practice covers the comparison of the performance of water-emulsion floor polishes on test floors against a reference
material. It is applicable to the following types of polishes:
1.1.1 Wax emulsion polishes,
1.1.2 Nonbuffable emulsion polishes,
1.1.3 Detergent-resistant emulsion polishes, household type, and
1.1.4 Detergent-resistant emulsion polishes, industrial type.
1.2 Gloss, leveling, discoloration, traffic marking, slip resistance, and removal ease of these types of floor polishes is rated in
comparison to a reference material. Where applicable, detergent resistance is also evaluated. This method is not to be considered
as a recommended maintenance procedure.
1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information
only.
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
D523 Test Method for Specular Gloss
2.2 CSMA Bulletin:
3
245-70 Comparative Determination of Slip Resistance of Floor Polishes
3. Significance and Use
3.1 When comparing different floor polishes for an actual field performance, it is important that all surfaces used be prepared
in the same way. When this procedure is followed, variations in the test surfaces are minimized.
4. Apparatus
4
4.1 Test Tile, OVCT.
1
This practice is under the jurisdiction of ASTM Committee D21 on Polishes and is the direct responsibility of Subcommittee D21.04 on Performance Tests.
Current edition approved May 1, 2010March 1, 2017. Published May 2010April 2017. Originally approved in 1972. Last previous edition approved in 20032010 as
D3052 – 87 (2003).(2010). DOI: 10.1520/D3052-87R10.10.1520/D3052-17.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from the Chemical Specialties Manufacturers Association, 1001 Connecticut Avenue, NW, Washington, DC 20036.
4
Official Vinyl Composition Tile (OVCT) is available from the Chemical Specialties Manufacturers Association, 1001 Connecticut Avenue, NW, Wash- ington, DC
20036.OVCT tile may be obtained through Armstrong Flooring from various home improvement stores. The following Armstrong tile substrates have been found to perform
adequately for this test method: Armstrong Excelon Feature Tile: Black (56790), http://www.armstrong.com/commflooringna/product_details_toolbox_magnify.jsp?item_
id=47394.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D3052 − 17
4.2 Glossmeter, 60°—The instrument and the reference standards shall conform to the requirements prescribed in Test Method
D523, using an angle of reflection of 60°.
4.3 Floor Machine.
5. Procedure
5.1 The preferred substrate shall be Official Vinyl Composition Tile.
5.2 The test floor shall include both dark (black) and light (white) colored tiles laid out so that one half of the panel is all white
and the other half is all black.
5.3 The minimum test panel size for each polish tested shall be 3 ft (0.9 m) in width and 3 ft in length.
5.4 Prepa
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D3209-93(2023)(Test Method)
Standard Test Method for Freeze/Thaw Resistance of Polymer Floor Polishes

SIGNIFICANCE AND USE
3.1 This test method is used to determine the effect of freezing on floor polishes. It may be used to predict the stability of a floor polish when exposed to freezing.
SCOPE
1.1 This test method covers the determination of the stability of polymer emulsion floor polishes when these are exposed to repeated cycles of freezing and thawing. Possible degradation of the emulsion is observed and possible reduction of initial gloss is measured.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D5678-17(2023)(Test Method)
Standard Test Method for Freeze/Thaw Resistance of Wax Emulsion Floor Polish

SIGNIFICANCE AND USE
3.1 This test method is used to determine the effect of freezing on wax emulsion floor polishes. It may be used to predict the stability of a floor polish in transit or when exposed to freezing, and whether or not the polish is damaged by freezing.
SCOPE
1.1 This test method covers the determination of the stability of wax emulsion floor polishes when these are exposed to repeated cycles of freezing and thawing. Possible degradation of the emulsion is observed and possible reduction of initial gloss is measured.  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D4002-81(2023)(Practice)
Standard Practice for Evaluation of Buffable Shoe Polish

SIGNIFICANCE AND USE
3.1 This practice is intended to define the properties to be tested, the apparatus to use, and the comparisons of product performance. It is recognized that considerable discretion exists among formulators and marketers of shoe polish on what properties or performance characteristics are best for their products. This practice will be flexible to honor this fact within the confines of the shoe polish definition in 2.1.
SCOPE
1.1 This practice covers the definition of properties to test and the apparatus to use, in evaluating the performance of buffable shoe polishes.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM D1792-17(2023)(Test Method)
Standard Test Method for Long-Term Removability Properties of Emulsion Floor Polishes

SIGNIFICANCE AND USE
4.1 This test method is used to predict removability of floor polish after a treatment period that simulates aging in the field. It allows for uniform mechanical and detergent action leaving the only variable the actual removability of the polish.
SCOPE
1.1 This test method covers the determination of the relative ease of removal of dried films of water-emulsion floor polishes from common flooring substrates under accelerated conditions, which correspond to extended service aging.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D1455-17(2023)(Test Method)
Standard Test Method for 60° Specular Gloss of Emulsion Floor Polish

SIGNIFICANCE AND USE
4.1 This test method may be used to evaluate the difference in gloss of dried films of emulsion floor polishes when the light reflected at a 60° angle is measured. Extremely high- or low-gloss polishes may not be differentiated at a 60° angle. A20° angle measured in accordance with Test Method D523 may give better definition of gloss.
SCOPE
1.1 This test method covers the determination of the 60° specular gloss of films of emulsion floor polish after application to a substrate.  
Note 1: Specular gloss is one of several related appearance attributes that produce the sensation of glossiness. For this reason, specular gloss measurements may not always correlate well with visual rankings of glossiness.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D3210-95(2023)(Test Method)
Standard Test Method for Comparing Colors of Films from Water-Emulsion Floor Polishes

SIGNIFICANCE AND USE
5.1 Whiteness index obtained from reflectance measurements on exaggerated dried polish films on filter paper can be used as a measurement of the color of such films.  
5.2 Whiteness index may be useful in predicting the potential discoloring effect of polish films on flooring substrates.  
5.3 Whiteness index should be useful in specifications when color comparisons are made with a standard sample polish.
SCOPE
1.1 This test method covers comparing colors of films (or solids) deposited from the emulsified particles in water emulsion floor polishes. It is based upon luminous reflectance measurements made with tristimulus colorimeters such as the Hunter Color Difference Meter.2  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D1791-93(2022)(Test Method)
Standard Test Method for Accelerated Aging of Liquid Water-Emulsion Floor Polishes

SIGNIFICANCE AND USE
3.1 This test method is not absolute but does give an indication of the useful shelf-life of a liquid water-emulsion floor polish. Will indicate whether a polish will gel or remain a usable liquid over the desired storage life of the product. It should be noted that polishes of different composition types will vary in useful storage life under identical storage conditions.
SCOPE
1.1 This test method covers the storage stability of liquid water-emulsion floor polishes.  
1.2 Storage for 30 days at 52 °C (125 °F), while not a guarantee of one year stability at 21 °C (70 °F), is believed to be a more reliable indicator of storage stability than similar tests of shorter duration.  
Note 1: The 60° specular gloss on black glass determined by Test Method D1455, may be used to confirm this observation. A substantial difference in gloss between aged and unaged samples is an indication of instability. A shelf stability of one year can be reasonably expected of the material in question if duplicate samples remain unchanged for 30 days at 52 °C ± 1.1 °C (125 °F ± 2 °F). If one or both duplicates show more than slight viscosity increases or slight creaming, other evidence of stability must be sought.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D3954-15(2022)(Test Method)
Standard Test Method for Dropping Point of Waxes

SIGNIFICANCE AND USE
4.1 Waxes do not go through a sharp solid-liquid phase change when heated and therefore do not have a true melting point. As the temperature rises, waxes gradually soften or become less viscous. For this reason, the determination of the softening point must be made by an arbitrary but closely defined method if test values are to be reproducible.  
4.2 This test is useful in determining the consistency of waxes, and as one element in establishing the uniformity of shipments or source of supply.  
4.3 This test method has been found suitable for all types of waxes including paraffin, microcrystalline polyethylene, and natural waxes.
SCOPE
1.1 This test method covers the determination of the ASTM dropping point for waxes.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D2834-95(2022)(Test Method)
Standard Test Method for Nonvolatile Matter (Total Solids) in Water-Emulsion Floor Polishes, Solvent-Based Floor Polishes, and Polymer-Emulsion Floor Polishes

SIGNIFICANCE AND USE
2.1 Nonvolatile matter determination is useful as a quality control test, when used in conjunction with other tests, to assure specification compliance.
SCOPE
1.1 This test method covers the determination of nonvolatile matter (total solids) in a water-emulsion, organic solvent-based liquid and paste floor polishes, and polymer-emulsion-type floor polishes.  
1.2 This test method recognizes that the products may contain material that will slowly volatilize or change chemically with a resulting change in weight of the nonvolatile matter. Therefore, since drying to constant weight is impractical, specific drying times have been selected.  
1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D3564-22(Practice)
Standard Practice for Application of Floor Polishes to Maintain Vinyl Composition Tile or Flooring

SIGNIFICANCE AND USE
2.1 Vinyl composition tile or flooring consists of vinyl resins (suitably plasticized and stabilized) fortified with composition fibers, mineral fillers, and prime pigments. In some cases, all or part of the wearing surfaces may consist of unfilled vinyl resin that is clear or translucent. Metallic accents (chips, pigment, etc.) are frequently used to form the overall design. In general, the overall binder content is lower than that of homogeneous vinyl tile. For the purpose of this practice, vinyl composition also includes vinyl asbestos tile.
SCOPE
1.1 This practice covers the application of floor polishes to maintain vinyl composition tile or flooring. Floor polishes are applied to vinyl composition tile floors for protection and beautification of the floor surface. Cleaning, polish application, removal, and maintenance procedures are important functions in this process.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off