ASTM C1729-12b
(Specification)Standard Specification for Aluminum Jacketing for Insulation
Standard Specification for Aluminum Jacketing for Insulation
SCOPE
1.1 This specification covers aluminum jacketing for thermal and acoustical insulation operating at either above or below ambient temperatures and in both indoor and outdoor locations. It does not cover insulation jacketing made from other materials such as mastics, fiber reinforced plastic, PVC, or stainless steel nor does it cover the details of thermal or acoustical insulation systems.
1.2 This specification provides physical requirements for aluminum jacketing for thermal and acoustical insulation. Guide C1423 provides guidance in selecting jacketing materials and their safe use.
1.3 This is a material specification and does not imply any performance of the installed system using the materials specified herein. For information about installation of aluminum jacketing, see (1).2
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:C1729 −12b
StandardSpecification for
1
Aluminum Jacketing for Insulation
This standard is issued under the fixed designation C1729; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope C450Practice for Fabrication of Thermal Insulating Fitting
Covers for NPS Piping, and Vessel Lagging
1.1 This specification covers aluminum jacketing for ther-
C585Practice for Inner and Outer Diameters of Thermal
mal and acoustical insulation operating at either above or
Insulation for Nominal Sizes of Pipe and Tubing
below ambient temperatures and in both indoor and outdoor
C835Test Method for Total Hemispherical Emittance of
locations. It does not cover insulation jacketing made from
Surfaces up to 1400°C
other materials such as mastics, fiber reinforced plastic, PVC,
C1371Test Method for Determination of Emittance of
or stainless steel nor does it cover the details of thermal or
Materials Near Room Temperature Using Portable Emis-
acoustical insulation systems.
someters
1.2 This specification provides physical requirements for
C1423Guide for Selecting Jacketing Materials for Thermal
aluminum jacketing for thermal and acoustical insulation.
Insulation
Guide C1423 provides guidance in selecting jacketing materi-
D3363Test Method for Film Hardness by Pencil Test
als and their safe use.
E84Test Method for Surface Burning Characteristics of
Building Materials
1.3 This is a material specification and does not imply any
performance of the installed system using the materials speci- F1249Test Method for Water Vapor Transmission Rate
Through Plastic Film and Sheeting Using a Modulated
fied herein. For information about installation of aluminum
2
jacketing, see (1). Infrared Sensor
4
2.2 ANSI Standard:
1.4 The values stated in inch-pound units are to be regarded
as standard. The values given in parentheses are mathematical ANSI H35.2/H35.2(M)Dimensional Tolerances for Alumi-
num Mill Products
conversions to SI units that are provided for information only
and are not considered standard.
3. Terminology
1.5 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the
3.1 Definitions—Definitions in Terminology C168 apply to
responsibility of the user of this standard to establish appro-
terms used in this specification.
priate safety and health practices and determine the applica-
3.2 Definitions of Terms Specific to This Standard:
bility of regulatory limitations prior to use.
3.2.1 box rib—aluminum sheet formed to have alternating
parallel grooves and ridges with a cross section approximating
2. Referenced Documents
a square wave
3
2.1 ASTM Standards:
3.2.2 cladding—synonymous with jacketing
B209Specification for Aluminum and Aluminum-Alloy
3.2.2.1 Discussion—Thethreeterms“jacketing”,“lagging”,
Sheet and Plate
and “cladding” are considered synonymous in most metal
C168Terminology Relating to Thermal Insulation
jacket related applications and geographies. However, in some
cases in the power industry in North America the term
1
This specification is under the jurisdiction of ASTM Committee C16 on
“lagging” has a different meaning than “jacketing” or “clad-
Thermal Insulation and is the direct responsibility of Subcommittee C16.40 on
ding” and refers specifically to a heavier gauge of jacketing.
Insulation Systems.
Current edition approved Nov. 1, 2012. Published January 2013. Originally
3.2.3 crevice corrosion—a type of corrosion occurring on
approved in 2010. Last previous edition approved in 2012 as C1729–12a DOI:
metal jacketing caused by differences in oxygen concentration
10.1520/C1729–12B.
in the electrolyte in adjacent regions of the material. These
2
The boldface numbers in parentheses refer to a list of references at the end of
this standard.
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
4
Standards volume information, refer to the standard’s Document Summary page on Available fromAmerican National Standards Institute (ANSI), 25 W. 43rd St.,
the ASTM website. 4th Floor, New York, NY 10036, http://www.ansi.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C1729−12b
differences lead to a concentration cell and the region on the 5.1.2 Alloy and Temper per Specification B209:
metal jacketing which is oxygen-starved is subject to corro- 5.1.2.1 Grade 1 = Alloy 3105 or 3003, half hard temper
sion. (H14,)
3 5.1.2.2 Grade 2 =Alloy 3105 or 3003, q
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: C1729 − 12a C1729 − 12b
Standard Specification for
1
Aluminum Jacketing for Insulation
This standard is issued under the fixed designation C1729; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers aluminum jacketing for thermal and acoustical insulation operating at either above or below
ambient temperatures and in both indoor and outdoor locations. It does not cover insulation jacketing made from other materials
such as mastics, fiber reinforced plastic, PVC, or stainless steel nor does it cover the details of thermal or acoustical insulation
systems.
1.2 This specification provides physical requirements for aluminum jacketing for thermal and acoustical insulation. Guide
C1423 provides guidance in selecting jacketing materials and their safe use.
1.3 This is a material specification and does not imply any performance of the installed system using the materials specified
2
herein. For information about installation of aluminum jacketing, see (1).
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
3
2.1 ASTM Standards:
B209 Specification for Aluminum and Aluminum-Alloy Sheet and Plate
C168 Terminology Relating to Thermal Insulation
C450 Practice for Fabrication of Thermal Insulating Fitting Covers for NPS Piping, and Vessel Lagging
C585 Practice for Inner and Outer Diameters of Thermal Insulation for Nominal Sizes of Pipe and Tubing
C835 Test Method for Total Hemispherical Emittance of Surfaces up to 1400°C
C1371 Test Method for Determination of Emittance of Materials Near Room Temperature Using Portable Emissometers
C1423 Guide for Selecting Jacketing Materials for Thermal Insulation
D3363 Test Method for Film Hardness by Pencil Test
E84 Test Method for Surface Burning Characteristics of Building Materials
F1249 Test Method for Water Vapor Transmission Rate Through Plastic Film and Sheeting Using a Modulated Infrared Sensor
4
2.2 ANSI Standard:
ANSI H35.2/H35.2(M) Dimensional Tolerances for Aluminum Mill Products
3. Terminology
3.1 Definitions—Definitions in Terminology C168 apply to terms used in this specification.
3.2 Definitions of Terms Specific to This Standard:
3.2.1 box rib—aluminum sheet formed to have alternating parallel grooves and ridges with a cross section approximating a
square wave
1
This specification is under the jurisdiction of ASTM Committee C16 on Thermal Insulation and is the direct responsibility of Subcommittee C16.40 on Insulation
Systems.
Current edition approved March 1, 2012Nov. 1, 2012. Published June 2012January 2013. Originally approved in 2010. Last previous edition approved in 2012 as
C1729–12.–12a DOI: 10.1520/C1729–12A.10.1520/C1729–12B.
2
The boldface numbers in parentheses refer to a list of references at the end of this standard.
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
4
Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C1729 − 12b
3.2.2 cladding—synonymous with jacketing
3.2.2.1 Discussion—
The three terms “jacketing”, “lagging”, and “cladding” are considered synonymous in most metal jacket related applications and
geographies. However, in some cases in the power industry in North America the term “lagging” has a different meaning than
“jacketing” or “cladding” and refers specifically to a heavier gauge of jacketing.
3.2.3 crevice corrosion—a type of corrosion occurring on metal jacketing caused by differences in oxygen concentrat
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.