ASTM D2683-20
(Specification)Standard Specification for Socket-Type Polyethylene Fittings for Outside Diameter-Controlled Polyethylene Pipe and Tubing
Standard Specification for Socket-Type Polyethylene Fittings for Outside Diameter-Controlled Polyethylene Pipe and Tubing
ABSTRACT
This specification covers polyethylene socket-type fittings for use with outside diameter-controlled polyethylene pipe and tubing. Fittings covered by this specification are normally molded. In-line fittings such as couplings, unions, bushings, caps, nipples, etc., may be extruded or machined from extruded stock. Special fittings such as transition fittings and tapping teets shall be assembled and fabricated. Conditioning, dimensions, short-term rupture test, and sustained pressure test shall be performed to conform with the requirements specified.
SCOPE
1.1 This specification covers polyethylene socket-type fittings for use with outside diameter-controlled polyethylene pipe as specified by Specifications D3035 and D2513. Requirements for materials, workmanship, dimensions, and pressure performance are included. Where applicable in this specification, “ pipe” shall mean “pipe and tubing.”
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 The following safety hazards caveat pertains only to the test method portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation:D2683 −20 An American National Standard
Standard Specification for
Socket-Type Polyethylene Fittings for Outside Diameter-
1
Controlled Polyethylene Pipe and Tubing
This standard is issued under the fixed designation D2683; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope* D1600 Terminology forAbbreviatedTerms Relating to Plas-
tics
1.1 This specification covers polyethylene socket-type fit-
D2122 Test Method for Determining Dimensions of Ther-
tings for use with outside diameter-controlled polyethylene
moplastic Pipe and Fittings
pipeasspecifiedbySpecificationsD3035andD2513.Require-
D2513 Specification for Polyethylene (PE) Gas Pressure
ments for materials, workmanship, dimensions, and pressure
Pipe, Tubing, and Fittings
performance are included. Where applicable in this
D3035 SpecificationforPolyethylene(PE)PlasticPipe(DR-
specification, “ pipe” shall mean “pipe and tubing.”
PR) Based on Controlled Outside Diameter
1.2 The values stated in inch-pound units are to be regarded
D3350 Specification for Polyethylene Plastics Pipe and Fit-
as standard. The values given in parentheses are mathematical
tings Materials
conversions to SI units that are provided for information only
F412 Terminology Relating to Plastic Piping Systems
and are not considered standard.
F2620 Practice for Heat Fusion Joining of Polyethylene Pipe
1.3 The following safety hazards caveat pertains only to the
and Fittings
test method portion, Section 8, of this specification: This
2.2 Federal Standard:
3
standarddoesnotpurporttoaddressallofthesafetyconcerns,
Fed. Std. No. 123 Marking for Shipment (Civil Agencies)
ifany,associatedwithitsuse.Itistheresponsibilityoftheuser
2.3 Military Standard:
3
of this standard to establish appropriate safety, health, and
MIL-STD-129 Marking for Shipment and Storage
4
environmental practices and determine the applicability of
2.4 Plastic Pipe Institute
regulatory limitations prior to use.
PPI TR-3 Policies and Procedures for Developing Hydro-
1.4 This international standard was developed in accor-
static Design Basis (HDB), Pressure Design Basis (PDB),
dance with internationally recognized principles on standard-
Strength Design Basis (SDB), and Minimum Required
ization established in the Decision on Principles for the
Strength (MRS) Ratings for Thermoplastic Piping Mate-
Development of International Standards, Guides and Recom-
rials or Pipe7
mendations issued by the World Trade Organization Technical
PPI TR-4 HDB/SDB/PDB/MRS Listed Materials, PPI List-
Barriers to Trade (TBT) Committee.
ing of Hydrostatic Design Basis (HDB), Strength Design
Basis(SDB),PressureDesignBasis(PDB),andMinimum
2. Referenced Documents
Required Strength (MRS) Ratings for Thermoplastic Pip-
2
2.1 ASTM Standards:
ing Materials or Pipe
D618 Practice for Conditioning Plastics for Testing
D1598 Test Method for Time-to-Failure of Plastic Pipe
3. Terminology
Under Constant Internal Pressure
3.1 Definitions are in accordance with Terminology F412
D1599 Test Method for Resistance to Short-Time Hydraulic
and abbreviations are in accordance with Terminology D1600,
Pressure of Plastic Pipe, Tubing, and Fittings
unless otherwise specified. The abbreviation of polyethylene
plastic is PE.
1
This specification is under the jurisdiction ofASTM Committee F17 on Plastic
3.2 standard thermoplastic pipe dimension ratio (SDR)—
Piping Systems and is the direct responsibility of Subcommittee F17.10 on Fittings.
the ratio of pipe outside diameter to wall thickness. It is
Current edition approved Nov. 1, 2020. Published November 2020. Originally
approved in 1968. Last previous edition approved in 2014 as D2683 – 14. DOI:
10.1520/D2683-20.
2 3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or DLA Document Services Building 4/D 700 Robbins Avenue Philadelphia, PA
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM 19111-5094 http://quicksearch.dla.mil/
4
Standards volume information, refer to the standard’s Document Summary page on Available from Plastics Pipe Institute (PPI), 105 Decker Court, Suite 825,
the ASTM website. Irving, TX 75062, http://www.plasticpipe.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
-------
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D2683 − 14 D2683 − 20 An American National Standard
Standard Specification for
Socket-Type Polyethylene Fittings for Outside Diameter-
1
Controlled Polyethylene Pipe and Tubing
This standard is issued under the fixed designation D2683; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope*
1.1 This specification covers polyethylene socket-type fittings for use with outside diameter-controlled polyethylene pipe as
specified by Specifications D3035 and D2513. Requirements for materials, workmanship, dimensions, and pressure performance
are included. Where applicable in this specification, “ pipe” shall mean “pipe and tubing.”
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.3 The following safety hazards caveat pertains only to the test method portion, Section 88,, of this specification:This standard
does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this
standard to establish appropriate safety safety, health, and healthenvironmental practices and determine the applicability of
regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
D618 Practice for Conditioning Plastics for Testing
D1598 Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
D1599 Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings
D1600 Terminology for Abbreviated Terms Relating to Plastics
D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D2513 Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings
D2657 Practice for Heat Fusion Joining of Polyolefin Pipe and Fittings
D3035 Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter
D3350 Specification for Polyethylene Plastics Pipe and Fittings Materials
F412 Terminology Relating to Plastic Piping Systems
F2620 Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings
1
This specification is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.10 on Fittings.
Current edition approved Nov. 1, 2014Nov. 1, 2020. Published December 2014November 2020. Originally approved in 1968. Last previous edition approved in 20102014
ε3
as D2683 – 10D2683 – 14. . DOI: 10.1520/D2683-14.10.1520/D2683-20.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D2683 − 20
2.2 Federal Standard:
3
Fed. Std. No. 123 Marking for Shipment (Civil Agencies)
2.3 Military Standard:
3
MIL-STD-129 Marking for Shipment and Storage
4
2.4 Plastic Pipe Institute
PPI TR-3 Policies and Procedures for Developing Hydrostatic Design Basis (HDB), Pressure Design Basis (PDB), Strength
Design Basis (SDB), and Minimum Required Strength (MRS) Ratings for Thermoplastic Piping Materials or Pipe7
PPI TR-4 HDB/SDB/PDB/MRS Listed Materials, PPI Listing of Hydrostatic Design Basis (HDB), Strength Design Basis
(SDB), Pressure Design Basis (PDB), and Minimum Required Strength (MRS) Ratings for Thermoplastic Piping Materials
or Pipe
3. Terminology
3.1 Definitions are in accordance with Terminology F412 and abbreviations are in accordance with Terminology D1600, unless
otherwise specified. The abbreviation of polyethylene plast
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.