ASTM D5677-05

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
An American National Standard
Designation: D5677 – 05
Standard Specification for
Fiberglass (Glass-Fiber-Reinforced Thermosetting-Resin)
Pipe and Pipe Fittings, Adhesive Bonded Joint Type, for
1
Aviation Jet Turbine Fuel Lines
This standard is issued under the fixed designation D5677; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope* D2310 Classification for Machine-Made “Fiberglass”
(Glass-Fiber-Reinforced Thermosetting-Resin) Pipe
1.1 This specification covers a reinforced plastic pipe and
D2412 Test Method for Determination of External Loading
fittings system made from epoxy resin and glass-fiber rein-
Characteristics of Plastic Pipe by Parallel-Plate Loading
forcement, together with adhesive for joint assembly, intended
D3241 Test Method for Thermal Oxidation Stability of
for service up to 150°F (65.6°C) and 150-psig (1034-kPa)
Aviation Turbine Fuels (JFTOT Procedure)
operating pressure and surges up to 275 psig (1896 kPa) in
D3567 Practice for Determining Dimensions of “Fiber-
aviation jet turbine fuel lines installed below ground.
glass” (Glass-Fiber-ReinforcedThermosetting Resin) Pipe
1.2 The dimensionless designator NPS has been substituted
and Fittings
in this specification for such traditional terms as nominal
D3951 Practice for Commercial Packaging
diameter, size, and nominal size.
F412 Terminology Relating to Plastic Piping Systems
1.3 Thevaluesstatedininch-poundunitsaretoberegarded
F1173 Specification for Thermosetting Resin Fiberglass
asstandard.Thevaluesinparenthesesareforinformationonly.
Pipe Systems to Be Used for Marine Applications
1.4 The following safety hazards caveat pertains only to the
2.2 Military Specification:
test method portion, Section 9, of this specification: This
MIL-T-5624 Turbine Fuel,Aviation, Grades JP-4, JP-5 and
standard does not purport to address all of the safety concerns,
3
JP-5/JP-8 ST
if any, associated with its use. It is the responsibility of the user
2.3 ANSI Standard:
of this standard to establish appropriate safety and health
4
B16.5 Steel Pipe Flanges and Flanged Fittings
practices and determine the applicability of regulatory limita-
tions prior to use.
3. Terminology
NOTE 1—There is no similar or equivalent ISO standard.
3.1 Definitions—Definitions are in accordance with Termi-
nologies D883 and F412 and abbreviations are in accordance
2. Referenced Documents
with Terminology D1600, unless otherwise indicated.
2
2.1 ASTM Standards:
3.1.1 conductive—a pipe or fitting that meets the require-
D381 Test Method for Gum Content in Fuels by Jet Evapo-
ments for conductivity listed in Section 6 of Specification
ration
F1173.
D883 Terminology Relating to Plastics
3.2 Abbreviations:Abbreviation:
D1599 TestMethodforResistancetoShort-TimeHydraulic
3.2.1 RTRP, n—reinforced thermosetting resin pipe.
Pressure of Plastic Pipe, Tubing, and Fittings
D1600 Terminology for Abbreviated Terms Relating to
4. Classification
Plastics
4.1 General:
4.1.1 Pipe meeting this specification is classified by type,
grade, and class similar to Classification D2310.
1
This specification is under the jurisdiction of ASTM Committee D20 on 4.1.2 Fittings meeting this specification are also classified
Plastics and is the direct responsibility of Subcommittee D20.23 on Reinforced
by type (method of manufacture) and grades (generic type of
Plastic Piping System and Chemical Equipment.
resin).
Current edition approved Nov. 1, 2005. Published November 2005. Originally
approved in 1995. Last previous edition approved in 2000 as D5677–00 DOI:
10.1520/D5677-05.
2 3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or AvailablefromStandardizationDocumentsOrderDesk,Bldg.4SectionD,700
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.
4
Standards volume information, refer to the standard’s Document Summary page on Available from American National Standards Institute, 11 W. 42nd St., 13th
the ASTM website. Floor, New York, NY 10036.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
D5677 – 05
4.2 Pipe: 6. Dimensions
4.2.1 Type I Filament-Wound Pipe Nonconductive
6.1 Pipe—The pipe shall be 2, 3, 4, 6, 8, 10, 12, 14, and
4.2.2 Type Ia Filament-Wound Pipe Conductive
16-in. (50, 80, 100, 150, 200, 250, 300, 350 and 400-mm)
4.2.3 Type II Centrifug
...