iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D4919-03

(Specification)

Standard Specification for Testing of Hazardous Materials Packagings

Standard Specification for Testing of Hazardous Materials Packagings

ABSTRACT
This guide identifies the key information required to ensure that selected packaging will pass the United Nations (UN) packaging certification at the level that is appropriate for its intended use. This guide covers test procedures for transportation of hazardous material packagings for net masses except those used for infectious substances, radioactive materials, cylinders, and other receptacles for gases and does not replace domestic or international requlatory requirements for hazardous material packagings. The UN performance tests are based on the degree of hazard posed by the proposed materials to be packaged which are also assigned to a specific packing group. Only packaging designs that meet the UN performance standards are to be marked with a UN mark. Tests include drop test, leakproofness test, stack test, vibration test, pressure differential test, hydrostatic pressure test, and cobb water absorption test.
SCOPE
1.1 The main focus of this guide is to identify the key information required for United Nations (UN) packaging certification to ensure the selected packaging will be certified to the appropriate level for its intended use. This document also provides guidance for locating relevant sections of the United States Department of Transportation Title 49 Code of Federal Regulations (CFR). Consult with a regulatory specialist whenever needed.
1.2 This guide is intended to assist in determining the appropriate performance tests required to certify packaging designs to the United States Department of Transportation Title 49 Code of Federal Regulations performance oriented packaging standards based on the United Nations Recommendations on the Transport of Dangerous Goods.
1.3 This guide covers the testing for transportation of hazardous materials packagings for net masses not exceeding 400 kg (880 lb) or capacities not exceeding 450 L (119 gal), excepting packagings for infectious substances, radioactive materials, cylinders and other receptacles for gases.
1.4 This guide does not replace domestic or international regulatory requirements for hazardous materials packaging but is strongly recommended to be used in conjunction with those regulations.
1.5 The user of this guide must be trained in accordance with the United States Department of Transportation Title 49 Code of Federal Regulations as required by 172.700 and should be familiar with other applicable hazardous materials regulations such as; International Civil Aviation Organization (ICAO) Technical Instructions for the Safe Transport of Dangerous Goods by Air, and the International Maritime Dangerous Goods Code (IMDG Code) and carrier rules such as International Air Transport Association (IATA) Dangerous Goods Regulations.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

General Information

Status
Historical
Publication Date
09-Apr-2003
ICS
55.040 - Packaging materials and accessories
Technical Committee
D10 - Packaging
Drafting Committee
D10.21 - Shipping Containers and Systems - Application of Performance Test Methods
Current Stage
Ref Project

Relations

Replaces
ASTM D4919-89(1997) - Standard Specification for Testing of Hazardous Materials Packagings
Effective Date
10-Apr-2003
Replaced By
ASTM D4919-03(2008) - Standard Specification for Testing of Hazardous Materials Packagings (Withdrawn 2017)
Effective Date
01-Oct-2008
Referred By
ASTM D8135-17(2023) - Standard Guide for Selection of Substitute, Non-hazardous, Particulate Solid Filling Substances for Packagings Subjected to the United Nations Performance Tests
Effective Date
10-Apr-2003
Referred By
ASTM D6198-18 - Standard Guide for Transport Packaging Design
Effective Date
10-Apr-2003
Referred By
ASTM D5998-16 - Standard Specification for Molded Polyethylene Shipping and Storage Drums
Effective Date
10-Apr-2003
Referred By
ASTM D7660-20 - Standard Guide for Conducting Internal Pressure Tests on United Nations (UN) Packagings
Effective Date
10-Apr-2003
Referred By
ASTM D8409-21 - Standard Guide for Conducting Stacking Tests on UN Packagings Using Guided or Unguided Loads
Effective Date
10-Apr-2003
Referred By
ASTM D8134-18 - Standard Guide for Conducting Internal Hydrostatic Pressure Tests on United Nations (UN) IBC Design Types
Effective Date
10-Apr-2003
Referred By
ASTM D7790-19 - Standard Guide for Preparation of Plastic Packagings Containing Liquids for United Nations (UN) Drop Testing
Effective Date
10-Apr-2003
Referred By
ASTM D7387-20 - Standard Test Method for Vibration Testing of Intermediate Bulk Containers (IBCs) Used for Shipping Liquid Hazardous Materials (Dangerous Goods)
Effective Date
10-Apr-2003
Referred By
ASTM D7887-20 - Standard Guide for Selection of Substitute, Non-hazardous, Liquid Filling Substances for Packagings Subjected to the United Nations Performance Tests
Effective Date
10-Apr-2003

Buy Standard

ASTM D4919-03 - Standard Specification for Testing of Hazardous Materials PackagingsASTM D4919-03 - Standard Specification for Testing of Hazardous Materials Packagings
PreviousNext
Technical specification
ASTM D4919-03 - Standard Specification for Testing of Hazardous Materials Packagings
English language
9 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D 4919 – 03
Standard Guide for
1
Testing of Hazardous Materials Packagings
This standard is issued under the fixed designation D 4919; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope responsibility of the user of this standard to establish appro-
priate safety and health practices and determine the applica-
1.1 The main focus of this guide is to identify the key
bility of regulatory requirements prior to use.
information required for United Nations (UN) packaging
certification to ensure the selected packaging will be certified
2. Referenced Documents
totheappropriatelevelforitsintendeduse.Thisdocumentalso
2
2.1 ASTM Standards:
provides guidance for locating relevant sections of the United
D 323 Test Method for Vapor Pressure of Petroleum Prod-
States Department of Transportation Title 49 Code of Federal
ucts (Reid Method)
Regulations (CFR). Consult with a regulatory specialist when-
D 642 Test Method for Determining Compressive Resis-
ever needed.
tance of Shipping Containers, Components, and Unit
1.2 This guide is intended to assist in determining the
Loads
appropriate performance tests required to certify packaging
D 685 Practice for Conditioning Paper and Paper Products
designstotheUnitedStatesDepartmentofTransportationTitle
for Testing
49 Code of Federal Regulations performance oriented packag-
D 996 Terminology of Packaging and Distribution Environ-
ing standards based on the United Nations Recommendations
ments
on the Transport of Dangerous Goods.
D 999 Test Methods for Vibration Testing of Shipping
1.3 This guide covers the testing for transportation of
Containers
hazardous materials packagings for net masses not exceeding
D 4169 Practice for Performance Testing of Shipping Con-
400 kg (880 lb) or capacities not exceeding 450 L (119 gal),
tainers and Systems
excepting packagings for infectious substances, radioactive
D 4332 Practice for Conditioning Containers, Packages, or
materials, cylinders and other receptacles for gases.
Packaging Components for Testing
1.4 This guide does not replace domestic or international
D 4359 Test Method for DeterminingWhether a Material Is
regulatory requirements for hazardous materials packaging but
a Liquid or a Solid
is strongly recommended to be used in conjunction with those
D 4577 Test Method for Compression Resistance of a
regulations.
Container Under Constant Load
1.5 The user of this guide must be trained in accordance
D 4991 Test Method for Leakage Testing of Empty Rigid
with the United States Department of Transportation Title 49
Containers by Vacuum Method
Code of Federal Regulations as required by 172.700 and
D 5276 Test Method for DropTest of Loaded Containers by
should be familiar with other applicable hazardous materials
Free Fall
regulations such as; International Civil Aviation Organization
D 5570 Test Method for Water Resistance of Tape and
(ICAO) Technical Instructions for the Safe Transport of Dan-
Adhesives Used as Box Closure
gerous Goods by Air, and the International Maritime Danger-
2.2 ISO Standard:
ous Goods Code (IMDG Code) and carrier rules such as
ISO 535 Determination of Water Absorption of Paper and
International Air Transport Association (IATA) Dangerous
3
Board (Cobb Method)
Goods Regulations.
2.3 United Nations Document:
1.6 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
1
ThisguideisunderthejurisdictionofASTMCommitteeD10onPackagingand contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
is the direct responsibility of Subcommittee D10.21 on Shipping Container Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.
Environment.
3
Current edition approved April 10, 2003. Published August 2003. Originally Available fromAmerican National Standards Institute (ANSI), 25 W. 43rd St.,
approved in 1989. Last previous edition approved in 1989 as D 4919 – 89 (1997). 4th Floor, New York, NY 10036.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
D4919–03
United Nations Recommendations on the Transport of Dan- 3.8.2.2 Performance Standard “Y” Packaging—May be
4
gerous Goods used to transport hazardous materials in Packing Groups II and
2.4 Regulatory Documents: III.
International Air Transport Association (IATA)
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D7932-17(2023)(Specification)
Standard Specification for Printed, Pressure-Sensitive Adhesive Labels for Use in Extreme Distribution Environments

ABSTRACT
This specification provides a standard means for testing and measuring the performance characteristics of printed, pressure-sensitive adhesive labels for containers, particularly containers to be used in extreme distribution environments (for example, hazardous materials labels, aerospace, military containers). For the purposes of this specification, an extreme distribution environment is one in which it can be reasonably expected to experience direct exposure to deteriorating chemicals, weather, elevated/cold temperatures, and other environmental and physical elements for an extended period of time. This specification includes standard laboratory test methods to simulate exposure to various conditions and measure associated degradation of required performance characteristics. The data from these methods can be used as acceptance criteria between a supplier and customer. This specification covers the physical properties of the labels, as well as workmanship, finish and appearance, acceptance criteria, testing procedures, reporting of all the steps taken, certification, and preparation for delivery.
SCOPE
1.1 This specification provides a standard means to test and measure performance characteristics of printed, pressure-sensitive adhesive labels for containers, particularly containers to be used in extreme distribution environments (for example, hazardous materials labels, aerospace, military containers). For the purposes of this specification, an extreme distribution environment is one in which it can be reasonably expected to experience direct exposure to deteriorating chemicals, weather, elevated/cold temperatures, and other environmental and physical elements for an extended period of time.  
1.2 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    8 pages
    English language
    sale 15% off
ASTM
ASTM D4577-19(2023)(Test Method)
Standard Test Method for Compression Resistance of a Container Under Constant Load

SIGNIFICANCE AND USE
4.1 In the distribution system for many products there is a phase wherein the packaged product may be stored for a period of time in a manner such that one or more containers are superimposed one upon the other. Failure can occur in any layer4 (see Fig. 1 and Fig. 3).
FIG. 1 Containers Under Constant Load of Dead Weights Imposed by Other Containers
FIG. 2 Container Under Constant Load of Dead Weights
FIG. 3 Containers Under Constant Load in Compression Test Machine With Fixed Platen  
4.2 This test method subjects a container, empty or filled, to a predetermined static load, and to specified atmospheric conditions, if required.
SCOPE
1.1 This test method is designed to determine the resistance of a shipping container to a vertically applied constant load for either a specified time or to failure. The test method may also be used for palletized or unitized load configurations.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements, see Section 6.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    8 pages
    English language
    sale 15% off
ASTM
ASTM D3332-99(2023)(Test Method)
Standard Test Methods for Mechanical-Shock Fragility of Products, Using Shock Machines

SIGNIFICANCE AND USE
4.1 These test methods are intended to provide the user with data on product shock fragility that can be used in choosing optimum-cushioning materials for shipping containers or for product design modification.
SCOPE
1.1 These test methods cover determination of the shock fragility of products. This fragility information may be used in designing shipping containers for transporting the products. It may also be used to improve product ruggedness. Unit or consumer packages, which are transported within an outer container, are considered to be the product for the purposes of these test methods. Two test methods are outlined, as follows:  
1.1.1 Test Method A is used first, to determine the product's critical velocity change.  
1.1.2 Test Method B is used second, to determine the product's critical acceleration.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements, see Section 6.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    8 pages
    English language
    sale 15% off
ASTM
ASTM D1596-14(2023)(Test Method)
Standard Test Method for Dynamic Shock Cushioning Characteristics of Packaging Material

SIGNIFICANCE AND USE
5.1 Dynamic cushioning test data obtained by this test method are applicable to the cushioning material and not necessarily the same as obtained in a package. In addition to the influence of the package, the data can also be affected by the specimen area, thickness, loading rate, and other factors.
SCOPE
1.1 This test method covers a procedure for obtaining dynamic shock cushioning characteristics of packaging materials through acceleration-time data achieved from dropping a falling guided platen assembly onto a motionless sample. This test method does not address any effects or contributions of exterior packaging assemblies.  
1.2 The data acquired may be used for a single point or for use in developing a dynamic cushion curve for the specific material being tested. Such data may be used for comparison among different materials at specific input conditions, or qualifying materials against performance specifications. Caution should be used when attempting to compare data from different methods or when using such data for predicting in-package performance. Depending upon the particular materials of concern, correlation of such data (from among differing procedures or for predicting in–package performance) may be highly variable.
Note 1: Alternative and related method for possible consideration is Test Method D4168.  
1.3 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D3950-23(Specification)
Standard Specification for Strapping, Nonmetallic (and Joining Methods)

ABSTRACT
This specification covers nonmetallic strapping and joining methods for closing, reinforcing, and bundling materials for shipment, unitizing, palletizing, and bracing for car and truck loading. The strappings are classified into five types according to the type of materials used. If necessary, seals and buckles made from steel with zinc, black iron oxide, or any equivalent corrosion protective coatings or plastic buckles may be used. Each sample should be collected and tested using the given procedures and should conform to the required values of breaking strength and elongation, transverse strength, and joint strength, when applicable, for each strapping type.
SCOPE
1.1 This specification covers nonmetallic strapping and joining methods intended for use in closing, reinforcing, and bundling articles for shipment, unitizing, palletizing, and bracing for car loading and truck loading.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following safety hazards caveat pertains only to the test method portion, Section 12, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    9 pages
    English language
    sale 15% off
  • Technical specification
    9 pages
    English language
    sale 15% off
ASTM
ASTM D8410-22(Specification)
Standard Specification for Evaluation of Cellulosic-Fiber-Based Packaging Materials and Products for Compostability in Municipal or Industrial Aerobic Composting Facilities

SCOPE
1.1 This specification covers cellulosic-fiber-based packaging materials and products associated with food, landscape waste, and other compost feedstocks, which are intended to be composted under aerobic conditions in municipal and industrial composting facilities, where thermophilic temperatures are achieved.  
1.2 This specification covers cellulosic-based uncoated and coated packaging materials and products and covers whole packaging products. Products covered in this specification include cellulosic fiber-based products produced from cellulosic pulp, corrugated materials, containerboard, paper, paperboard, and molded fiber.  
1.3 This specification excludes end items where thermoplastic polymer is laminated or extruded to cellulosic substrates.  
1.4 This specification is intended to establish the requirements for labeling cellulosic-fiber-based packaging materials and products as “compostable in aerobic municipal and industrial composting facilities” in accordance with the guidelines issued by the Federal Trade Commission,2 provided the label includes proper qualifications as to the availability of such facilities.  
1.5 The properties in this specification are those required to determine if packaging materials and products will compost satisfactorily in large-scale aerobic municipal or industrial composting where maximum throughput is a high priority and where intermediate stages of biodegradation must not be apparent to the end user for aesthetic reasons.  
1.6 This specification is technically equivalent to ISO 18606.1.7.  
1.7 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM D4675-14a(2022)(Guide)
Standard Guide for Selection and Use of Flat Strapping Materials1

SIGNIFICANCE AND USE
4.1 This guide is intended to assist the user in selecting strapping material(s) and application method(s) for evaluation when subjected to handling, transit, and storage tests. It describes general load, unit and package types, strapping properties, strapping performance, weight considerations, shear planes, component frictional characteristics, and geometry.
SCOPE
1.1 This guide1 covers information on flat strapping materials (steel and nonmetallic) for the prospective user wanting initial guidance in selecting a strapping material and information on suggested application methods for use in packaging (closing, reinforcing, baling, bundling, unitizing, or palletizing), and loading applications (load unitization and securement to transport vehicle). The use applies to handling, securement, storage, and distribution systems.  
1.2 Carrier associations have established certain packaging and loading requirements that (in some cases) specify the type of strap, the minimum size or strength, the type of joint or seal, and the number of straps, seals, and joints that must be used for particular types of shipments or under certain conditions. Users should consult with their carriers initially to determine if there are applicable published requirements. Individual carriers may establish their own requirements. (See 2.2.)  
1.3 Limitations—This guide is not intended to give specific information as to how strapping must be used in any particular packaging or loading situation. Rather, it is intended to be informational in nature and is offered as a starting point for the testing of strapping being considered by the user. Thorough user testing is essential, as is a review of pertinent regulations that can influence strap selection (size and type), and application methods.  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    20 pages
    English language
    sale 15% off
ASTM
ASTM D3953-15(2022)(Specification)
Standard Specification for Strapping, Flat Steel and Seals

ABSTRACT
This specification covers flat steel strapping and seals intended for use in closing, reinforcing, bundling articles for shipment, unitizing, palletizing, and bracing for carloading, truckloading, lifting, and lashing. This specification does not include specialty-type strapping as developed for special applications or strapping produced from alloy metals. Strapping shall be of the following types: Type 1 and Type II; shall be of the following finish: Finish A, Finish B including Grade 1, Grade 2, and Grade 3, Finish C and Finish D; and shall have the prescribed widths and thicknesses in accordance with the specified sizes. Seals shall be of the following classes: Class R and Class H; finishes: Finish A, Finish B including Grade 1, Grade 2, and Grade 3, Finish C, and Finish D; and styles: Style I, Style II, Style III, Style IV, and Style V. Materials shall be cold-rolled carbon steel of the prescribed quality. Strapping and seal shall conform to the physical and mechanical property requirements prescribed for: (1) breaking strength, elongation and seal joint strength, (2) lubrication (by lubricity and edge tests), (3) weld efficiency, (4) seal width, (5) seal application, (6) notch, crimp, and sealless joints, (7) galvanized strapping (by weight loss test), (8) ductility of strapping coating, (9) base metal ductility (by bending test), and (10) straightness (camber, coil set, and spiral twist). The coil configuration are specified and illustrated. Sampling and packaging requirements such as wrapping and packing are also detailed.
SCOPE
1.1 This specification covers flat steel strapping and seals intended for use in closing, reinforcing, bundling articles for shipment, unitizing, palletizing, and bracing for carloading, truckloading, lifting, and lashing.  
1.2 This specification includes strapping and seals made from carbon steel and applies only to the types and sizes as cataloged by strapping suppliers to be a standard, commercially available product. It does not include “specialty”-type strapping as developed for special applications or strapping produced from alloy metals.  
1.3 The values stated in inch-pound units are to be regarded as standard.  
1.4 Performance characteristics may be negatively affected by extremes of temperatures, such as occur during the annealing of steel.  
1.5 The following safety hazards caveat applies only to the test method portion, Sections 11, 12, and 13, of this specification:  
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    14 pages
    English language
    sale 15% off
ASTM
ASTM D4279-95(2022)(Test Method)
Standard Test Methods for Water Vapor Transmission of Shipping Containers—Constant and Cycle Methods

SIGNIFICANCE AND USE
4.1 These test methods are normally used for the following purposes:  
4.1.1 To evaluate materials and constructions for a specific type of container,  
4.1.2 To compare performance of different types of containers,  
4.1.3 To determine adequacy of protection for a specific product or application, and  
4.1.4 To maintain quality control.
SCOPE
1.1 These test methods cover the determination of water vapor transmission rates for bulk shipping containers, as follows:  
1.1.1 Method A, for Reclosable Containers, and  
1.1.2 Method B, for Containers Not Designed for Reclosing.  
1.2 Within each procedure details are given for the constant and cycle methods of test atmosphere.  
1.3 The test may be applied to the container as packed, or after one or more performance tests such as drum (Method D782), vibration (Methods D999), drop (Test Method D5276), impact resistance (Test Methods D880, D4003, and D5277), or performance tests (Practice D4169), as required.  
1.4 For small shipping containers requiring greater accuracy in weighing, the water vapor transmission may be determined in accordance with Test Method D895 or Test Method D1251.  
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D5168-22(Practice)
Standard Practice for Fabrication and Closure of Triple-Wall Corrugated Fiberboard Containers

SIGNIFICANCE AND USE
4.1 Triple-wall corrugated fiberboard containers are used to unitize products into containers of size and shape suitable for manual or mechanical handling and to protect the contents against environmental, handling, shipping, and storage conditions.  
4.2 This practice is intended to cover some of the basic constructions and styles of commercially available triple-wall fiberboard packaging used to unitize and protect contents.
SCOPE
1.1 This practice covers the fabrication and closure of new triple-wall corrugated fiberboard containers.  
1.2 This practice indicates the factors and components that must be controlled in the manufacture of triple-wall fiberboard containers.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    English language
    sale 15% off