65.060.10 - Agricultural tractors and trailed vehicles

ISO 789-1:2018 specifies test procedures for determining the power available at the power take-off (PTO) on agricultural tractors of the wheeled, track-laying or semi-track-laying type.

This document specifies safety requirements for, and clearance zones around, front-mounted power take-offs (PTO) on agricultural tractors.
NOTE 1 Further specifications for front-mounted power take-offs are given in ISO 8759-3.
It is not applicable to tractors which are designed to run in two directions, where either end can be considered to be the front or the rear.
NOTE 2 In this case, ISO 500 (all parts) apply.

ISO 789-9:2018 specifies test procedures for determining the power available at the drawbar on agricultural tractors of the wheeled, track-laying or semi-track-laying type.

This document provides a list of the recommended mechanical connection combination standards for towing and towed agricultural vehicles.

This document defines hydraulic power beyond. It specifies the number, type, capacity, and identification of the connections between agricultural and forestry tractors and implements.

This document specifies the dimensional requirements and location for a ball coupling device of 80 mm nominal diameter, whose male part is fitted to an agricultural towing vehicle and female part is fitted to a towed, non-balanced vehicle which provides mechanical connection between the two vehicles. It defines vertical loading for different positions. This document specifies a ball coupling device with either a horizontal adjustable version, or a close position version.

This European Standard specifies safety requirements and their verification for the design and construction of trailers with a tipping body, balanced or semi-mounted, used in agriculture, as defined in 3.1. It includes also hook-lift trailers and trailers with conveyor device as defined in 3.9.
This European Standard does not deal with trailers equipped with pick-up devices and/or rear spreading devices.
Trailers with a load push/push-off device, slats or alternating moving floor may be remove...view more

This European Standard specifies safety requirements and their verification for the design and construction of trailers with a tipping body, balanced or semi-mounted, used in agriculture, as defined in 3.1. It includes also hook-lift trailers and trailers with conveyor device as defined in 3.9.
This European Standard does not deal with trailers equipped with pick-up devices and/or rear spreading devices.
Trailers with a load push/push-off device, slats or alternating moving floor may be remove...view more

This document specifies a method of determining the position of the centre of gravity of agricultural tractors. The method is applicable to agricultural tractors having at least two axles fitted with wheels or tracks.

This document specifies safety requirements for, and clearance zones around, front-mounted power take-offs (PTO) on agricultural tractors. NOTE 1 Further specifications for front-mounted power take-offs are given in ISO 8759-3. It is not applicable to tractors which are designed to run in two directions, where either end can be considered to be the front or the rear. NOTE 2 In this case, ISO 500 (all parts) apply.

This document specifies dimensions and requirements for three-point linkage in association with a power lift for the attachment of implements or equipment to the front of agricultural tractors. It is not applicable to tractors which are designed to run in two directions, where either end can be considered to be the front or the rear. NOTE In this case, ISO 730 applies.

This document gives general specification and location requirements for front-mounted power take-offs (PTO) on agricultural tractors. NOTE 1 Further specifications for front-mounted power take-offs are given in ISO 8759-1. It is not applicable to tractors which are designed to run in two directions, where either end can be considered to be the front or the rear. NOTE 2 In this case, ISO 500 (all parts) apply.

This document defines the physical link between analogue cameras mounted on implements and operator terminals or monitors installed in tractor cabins. The interface supports up to two analogue video streams and provides electrical power to the cameras. It is designed to be installed inside the cab of agricultural equipment.

ISO 789-13:2018 gives terms and definitions for use in the other parts of ISO 789. Annex A provides a specimen test report for all parts of ISO 789.

ISO 789-1:2018 specifies test procedures for determining the power available at the power take-off (PTO) on agricultural tractors of the wheeled, track-laying or semi-track-laying type.

ISO 789-9:2018 specifies test procedures for determining the power available at the drawbar on agricultural tractors of the wheeled, track-laying or semi-track-laying type.

ISO 789-2:2018 specifies test procedures for determining the lifting capacity of rear-mounted three-point linkage systems: a) the maximum vertical force which can be exerted by the hydraulic lift at the lower hitch points throughout their full range of movement; b) the maximum vertical force which can be exerted by the hydraulic lift, at a point 610 mm to the rear of the hitch points on a frame attached to the three-point linkage, throughout its full range of movement. NOTE 1 A static test provi...view more

ISO 20383:2017 specifies the dimensions, characteristics, and positioning of Speed Identification Signs (SIS). These signs indicate the maximum equipment ground speed, based on the ground speed design capability, for an agricultural vehicle. A rear-facing SIS is visible to other operators on public roads approaching the equipment from behind. A forward-facing SIS, mounted on the front of towed equipment, alerts operators of the towing vehicle of the maximum specified ground speed capabilities at...view more

This European Standard is applicable to cabs of agricultural and forestry tractors and self-propelled sprayers. Its purpose is to limit the exposure of the operator (driver) to hazardous substances when applying plant protection products (PPP) and liquid fertilisers. This European Standard specifies different categories of cabs of agricultural and forestry tractors and self-propelled sprayers and the relevant requirements and test procedures in order to limit the exposure of the operator (driver...view more