33.040.60 - Powerline telecommunications
ICS 33.040.60 Details
Powerline telecommunications
Telekomunikacije po elektroenergetskih vodih
General Information
IEC SRD 63152-2:2022 provides design guidelines for implementation of city service continuity (CSC) specified in IEC 63152 and includes city service cases for various target organizations (municipality, town developer, building administrator, etc.). The city service cases included are not only for emergency use but also for normal time use.
- Standardization document63 pagesEnglish languagesale 15% off
This part of EN 50561 specifies limits and methods of measurement of radio disturbance characteristics for in-home communication apparatus that use the low voltage power installation as the transmission medium. This part of EN 50561 applies to equipment that uses frequencies including those above 30 MHz in order to communicate. Procedures are given for the measurement of signals generated by the equipment and limits are specified within the frequency range 9 kHz to 400 GHz. No measurement is required at frequencies where no limits are specified. The radiated emission requirements in this standard are not intended to be applicable to the intentional transmissions from a radio-transmitter as defined by the ITU, nor to any spurious emissions related to these intentional transmissions. NOTE The requirements defined in this standard effectively restrict the intended transmission frequencies to below 87,5 MHz.
- Standard17 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard – translation18 pagesSlovenian languagesale 10% offe-Library read for1 day
This part of EN 50561 specifies limits and methods of measurement of radio disturbance characteristics for in-home communication apparatus that use the low-voltage power installation as the transmission medium. This part of EN 50561 applies to equipment that communicate over this medium in the frequency range 1,606 5 MHz to 30 MHz. NOTE Similar equipment that communicate outside this frequency range is under study and will be covered by another European Standard. Procedures are given for the measurement of signals generated by the equipment and limits are specified for the frequency range 9 kHz to 400 GHz. No measurement is required at frequencies where no limit is specified.
- Standard25 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard – translation28 pagesSlovenian languagesale 10% offe-Library read for1 day
This part of EN 50561 specifies limits and methods of measurement of radio disturbance characteristics for
in-home communication apparatus that use the low voltage power installation as the transmission medium.
This part of EN 50561 applies to equipment that uses frequencies including those above 30 MHz in order to
communicate.
Procedures are given for the measurement of signals generated by the equipment and limits are specified
within the frequency range 9 kHz to 400 GHz. No measurement is required at frequencies where no limits
are specified.
The radiated emission requirements in this standard are not intended to be applicable to the intentional
transmissions from a radio-transmitter as defined by the ITU, nor to any spurious emissions related to these
intentional transmissions.
NOTE The requirements defined in this standard effectively restrict the intended transmission frequencies to below
87,5 MHz.
- Standard17 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard – translation18 pagesSlovenian languagesale 10% offe-Library read for1 day
Corrigendum to add correct superseding information in the foreword ('partially supersedes').
- Corrigendum1 pageEnglish languagesale 10% offe-Library read for1 day
- Corrigendum – translation1 pageSlovenian languagesale 10% offe-Library read for1 day
Corrigendum mentioned in OJEU summary list
Corrigendum to add correct superseding information in the foreword ('partially supersedes').
- Corrigendum1 pageEnglish languagesale 10% offe-Library read for1 day
- Corrigendum – translation1 pageSlovenian languagesale 10% offe-Library read for1 day
This part of EN 50561 specifies limits and methods of measurement of radio disturbance characteristics for in-home communication apparatus that use the low-voltage power installation as the transmission medium. This part of EN 50561 applies to equipment that communicate over this medium in the frequency range 1,606 5 MHz to 30 MHz. Similar equipment that communicate outside this frequency range is under study and will be covered by another European Standard. Procedures are given for the measurement of signals generated by the equipment and limits are specified for the frequency range 9 kHz to 400 GHz. No measurement is required at frequencies where no limit is specified.
- Standard25 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard – translation28 pagesSlovenian languagesale 10% offe-Library read for1 day
Clause 1 of IEC 60358-1:2012 is applicable with the following additions: This part of the IEC 60358 series applies to AC or DC single-phase coupling capacitors, with rated voltage > 1 000 V, connected between line and ground with a low voltage terminal either permanently earthed or connected to a device for power line carrier-frequency (PLC) applications at frequencies from 30 kHz to 500 kHz or similar applications (DC or AC) at power frequencies from 15 Hz to 60 Hz. The transmission requirements for coupling devices for power line carrier (PLC) systems are defined in IEC 60481.
- Standard22 pagesEnglish languagesale 10% offe-Library read for1 day
This EMC standard specifies requirements for emissions originating from within wire-line telecommunication networks using telephone wires and the immunity of those networks, including their in-premises extensions by references to harmonised EMC product standards and other standards with EMC requirements in combination with good engineering practice, when installed and operated as intended. This standard covers the frequency range 9 kHz to 400 GHz. The assessment of a network needs to be performed only in the frequency ranges where limits are defined in the relevant product standards. The emission limits set in this standard do not apply to the wanted emissions from embedded radio links within the network. The requirements have been selected so as to ensure that electromagnetic disturbances generated by a network, or parts thereof, operating normally do not exceed a level above which radio and telecommunications equipment or other equipment cannot operate as intended. Fault conditions of the network are not taken into account.
- Standard11 pagesEnglish languagesale 10% offe-Library read for1 day
This Technical Report applies to electrical equipment using signals in the frequency range 1,6 MHz to 30 MHz to transmit information on low voltage electrical systems, either on the public supply system or within installations in consumers' premises. It is a Technical Report covering the different standards for HF Power Line produced by SC205A. It points to related documents about: frequency bands, coexistence and filters; limits for the terminal output levels in the operating band; limits for conducted and radiated disturbance (product & installation EMC); measurement methods.
- Technical report7 pagesEnglish languagesale 10% offe-Library read for1 day
This standard applies to electrical equipment using signals in the frequency range 1,6 MHz to 30 MHz to transmit information on low voltage electrical systems, either on the public supply system or within installations in consumers. premises. It does not specify the signal modulation methods nor the coding methods nor functional features. Environmental requirements and tests are not included. The immunity requirements have been selected so as to ensure an adequate level of immunity for apparatus at residential, commercial and light industrial premises (Class 1 environment), and industrial premises supplied from a dedicated HV/MV or MV/LV transformers (Class 2 environment). The severity levels required by this standard may not cover extreme cases which may occur in any location but with a low probability of occurrence. In special cases situations will arise where the level of disturbances may exceed the levels specified in this standard (e.g. where a hand-held transmitter is used in proximity to an apparatus). In these instances special mitigation measures may be required.
- Standard18 pagesEnglish languagesale 10% offe-Library read for1 day
This part of EN 50561 specifies limits and methods of measurement of radio disturbance characteristics for PLC access network communication apparatus that use the low voltage power installation as the transmission medium. This European Standard applies to equipment that communicate over this medium in the frequency range 1,606 5 MHz to 30 MHz. Procedures are given for the measurement of signals generated by the equipment and limits are specified for the frequency range 9 kHz to 400 GHz. No measurement is required at frequencies where no limit is specified. PLC apparatus in the scope of this standard is intended to operate under the responsibility of the PLC access network operator. This part does not apply to PLC apparatus solely communicating to each other in the same home; such apparatus is in the scope of EN 50561-1.
- Draft26 pagesEnglish languagesale 10% offe-Library read for1 day
This part of EN 50561 specifies limits and methods of measurement of radio disturbance characteristics for PLC access network communication apparatus that use the low voltage power installation as the transmission medium. This European Standard applies to equipment that communicate over this medium in the frequency range 1,60 65 MHz to 30 MHz.
Procedures are given for the measurement of signals generated by the equipment and limits are specified for the frequency range 9 kHz to 400 GHz. No measurement is required at frequencies where no limit is specified.
- Draft26 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard applies to electrical equipment using signals in the [2-4 MHz] frequency range to transmit information on low voltage electrical systems/networks within installations in consumers’ premises for residential, commercial and light industrial environments.
The purpose of this European Standard is to describe a mechanism to limit mutual interferences between equipments operating in the [2-4 MHz] frequency band and to specify the way systems share the same band.
It does not specify the signal modulation methods nor the coding methods or functional features (except those preventing mutual interference in the same band).
Applications complying with this coexistence standard may offer low rate (lower than 1 Mb/s) services in home and building automation, street lighting control.
This European Standard covers typical applications such as energy efficiency, real-time displays of metering information, general command and control, home automation.
This European Standard does not cover high rate communication (higher than 1 Mb/s) applications such as Video or Internet networking.
This European Standard does not cover Output Voltage Levels.
- Draft14 pagesEnglish languagesale 10% offe-Library read for1 day
Not to be offered to IEC under the Dresden Agreement in order not to further delay the fulfillment of the mandate M/313
- Draft15 pagesEnglish languagesale 10% offe-Library read for1 day