IMT cellular networks - Harmonised Standard for access to radio spectrum - Part 13: Evolved Universal Terrestrial Radio Access (E-UTRA) User Equipment (UE)

The present document applies to the following radio equipment type:
• User Equipment for Evolved Universal Terrestrial Radio Access (E-UTRA).
E-UTRA NB-IoT is designed to operate in the E-UTRA operating bands 1, 3, 8, 20, 28 and 65 defined in table 1-1. The
present document covers requirements for E-UTRA FDD and E-UTRA TDD User Equipment from 3GPP™ Releases 8,
9, 10, 11, 12, and 13 defined in ETSI TS 136 101 [3]. This includes the requirements for E-UTRA UE operating bands
and E-UTRA CA operating bands from 3GPP™ Release 13 defined in ETSI TS 136 101 [3].
NOTE 2: For Band 20:
 For user equipment designed to be mobile or nomadic, the requirements in the present document
measured at the antenna port also show conformity to the corresponding requirement defined as
Total Radiated Power (TRP), as described in Commission Decision 2010/267/EU [i.6], ECC
Decision (09)03 [i.7].
 For user equipment designed to be fixed or installed, the present document does not address the
requirements described in Commission Decision 2010/267/EU [i.6], ECC Decision (09)03 [i.7].
The present document contains requirements to demonstrate that radio equipment both effectively uses and supports the
efficient use of radio spectrum in order to avoid harmful interference.

Celična omrežja IMT - Harmonizirani standard za dostop do radijskega spektra - 13. del: Uporabniška oprema za razviti prizemni radijski dostop za UMTS (E-UTRA)

Ta dokument se uporablja za radijsko opremo naslednje vrste:
• uporabniška oprema za razviti prizemni radijski dostop za UMTS (E-UTRA).
E-UTRA NB-IoT je zasnovan za delovanje v operativnih pasovih E-UTRA 1, 3, 8, 20, 28 in 65, ki so opredeljeni v preglednici 1-1. Ta dokument zajema zahteve za uporabniško opremo E-UTRA FDD in E-UTRA TDD iz izdaj 8, 9, 10, 11, 12 in 13 dokumenta 3GPP™, kot je opredeljeno v dokumentu ETSI TS 136-101 [3]. To vključuje zahteve za operativne pasove E-UTRA UE in operativne pasove CA E-UTRA iz izdaje 13 dokumenta 3GPP™, kot je opredeljeno v dokumentu ETSI TS 136-101 [3].
OPOMBA 2: Za pas 20:
 Za uporabniško opremo, ki je zasnovana kot mobilna ali nomadska, so zahteve iz tega dokumenta, izmerjene na antenskem vhodu, tudi v skladu z ustrezno zahtevo, opredeljeno kot TRP (skupna sevana moč), kot je opisana v Sklepu Komisije 2010/267/EU [i.6] in Sklepu Odbora za elektronske komunikacije (09)03 [i.7].
 Za uporabniško opremo, zasnovano za priključitev ali namestitev, ta dokument ne obravnava zahtev, opisanih v Sklepu Komisije 2010/267/EU [i.6] in Sklepu Odbora za elektronske komunikacije (09)03 [i.7].
Ta dokument vsebuje zahteve, s katerimi se dokazuje, da je radijska oprema izdelana tako, da učinkovito uporablja in podpira učinkovito rabo radijskega spektra z namenom preprečevanja škodljivih motenj.

General Information

Status
Published
Public Enquiry End Date
31-Jan-2022
Publication Date
14-Feb-2022
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
14-Feb-2022
Due Date
21-Apr-2022
Completion Date
15-Feb-2022

Buy Standard

Standard
ETSI EN 301 908-13 V13.2.1 (2022-02) - IMT cellular networks; Harmonised Standard for access to radio spectrum; Part 13: Evolved Universal Terrestrial Radio Access (E-UTRA) User Equipment (UE)
English language
148 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
EN 301 908-13 V13.2.1:2022
English language
148 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Standard
ETSI EN 301 908-13 V13.2.0 (2021-11) - IMT cellular networks; Harmonised Standard for access to radio spectrum; Part 13: Evolved Universal Terrestrial Radio Access (E-UTRA) User Equipment (UE)
English language
148 pages
sale 15% off
Preview
sale 15% off
Preview
Draft
prEN 301 908-13 V13.2.0:2022
English language
148 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

ETSI EN 301 908-13 V13.2.1 (2022-02)






HARMONISED EUROPEAN STANDARD
IMT cellular networks;
Harmonised Standard for access to radio spectrum;
Part 13: Evolved Universal Terrestrial Radio Access (E-UTRA)
User Equipment (UE)

---------------------- Page: 1 ----------------------
2 ETSI EN 301 908-13 V13.2.1 (2022-02)

Reference
REN/MSG-TFES-1137
Keywords
3G, 3GPP, cellular, digital, E-UTRA, IMT, LTE,
LTE-Advanced, mobile, radio, regulation, UMTS

ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Notice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.
No recommendation as to products and services or vendors is made or should be implied.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.

Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2022.
All rights reserved.

ETSI

---------------------- Page: 2 ----------------------
3 ETSI EN 301 908-13 V13.2.1 (2022-02)
Contents
Intellectual Property Rights . 11
Foreword . 11
Modal verbs terminology . 12
Introduction . 12
1 Scope . 13
2 References . 16
2.1 Normative references . 16
2.2 Informative references . 17
3 Definition of terms, symbols and abbreviations . 18
3.1 Terms . 18
3.2 Symbols . 21
3.3 Abbreviations . 23
4 Technical requirements specifications . 24
4.1 Environmental profile . 24
4.2 Conformance requirements . 24
4.2.0 General . 24
4.2.1 Introduction. 24
4.2.2 Transmitter Maximum Output Power . 25
4.2.2.1 Transmitter maximum output power for Single Carrier . 25
4.2.2.1.1 Definition. 25
4.2.2.1.2 Limits . 26
4.2.2.1.3 Conformance . 26
4.2.2.2 Transmitter output power for Carrier Aggregation (DL CA and UL CA) . 26
4.2.2.2.1 Definition. 26
4.2.2.2.2 Limits . 27
4.2.2.2.3 Conformance . 28
4.2.2.3 Transmitter output power for UL-MIMO . 28
4.2.2.3.1 Definition. 28
4.2.2.3.2 Limits . 28
4.2.2.3.3 Conformance . 28
4.2.2.4 Transmitter output power for category NB1 . 29
4.2.2.4.1 Definition. 29
4.2.2.4.2 Limits . 29
4.2.2.4.3 Conformance . 29
4.2.2.5 Transmitter output power for UE category M1 . 29
4.2.2.5.1 Definition. 29
4.2.2.5.2 Limits . 29
4.2.2.5.3 Conformance . 30
4.2.3 Transmitter Spectrum Emission Mask . 30
4.2.3.1 Transmitter spectrum emission mask for Single Carrier . 30
4.2.3.1.1 Definition. 30
4.2.3.1.2 Limits . 30
4.2.3.1.3 Conformance . 31
4.2.3.2 Transmitter spectrum emission mask for Carrier Aggregation (DL CA and UL CA) . 31
4.2.3.2.1 Definition. 31
4.2.3.2.2 Limits . 31
4.2.3.2.3 Conformance . 32
4.2.3.3 Transmitter spectrum emission mask for UL-MIMO . 32
4.2.3.3.1 Definition. 32
4.2.3.3.2 Limits . 32
4.2.3.3.3 Conformance . 32
4.2.3.4 Transmitter spectrum emission mask for Multi-Cluster PUSCH within a component carrier . 33
4.2.3.4.1 Definition. 33
4.2.3.4.2 Limits . 33
ETSI

---------------------- Page: 3 ----------------------
4 ETSI EN 301 908-13 V13.2.1 (2022-02)
4.2.3.4.3 Conformance . 33
4.2.3.5 Transmitter spectrum emission mask for category NB1 . 33
4.2.3.5.1 Definition. 33
4.2.3.5.2 Limits . 33
4.2.3.5.3 Conformance . 33
4.2.4 Transmitter Spurious Emissions . 33
4.2.4.1 Transmitter spurious emissions for Single Carrier . 33
4.2.4.1.1 Definition. 33
4.2.4.1.2 Limits . 33
4.2.4.1.3 Conformance . 37
4.2.4.2 Transmitter spurious emissions for Carrier Aggregation (DL CA and UL CA) . 37
4.2.4.2.1 Definition. 37
4.2.4.2.2 Limits . 38
4.2.4.2.3 Conformance . 43
4.2.4.3 Transmitter spurious emissions for UL-MIMO . 43
4.2.4.3.1 Definition. 43
4.2.4.3.2 Limits . 43
4.2.4.3.3 Conformance . 43
4.2.4.4 Transmitter spurious emissions for Multi-Cluster PUSCH within a component carrier . 43
4.2.4.4.1 Definition. 43
4.2.4.4.2 Limits . 43
4.2.4.4.3 Conformance . 44
4.2.4.5 Transmitter spurious emissions for category NB1 . 44
4.2.4.5.1 Definition. 44
4.2.4.5.2 Limits . 44
4.2.4.5.3 Conformance . 44
4.2.5 Transmitter Minimum Output Power . 44
4.2.5.1 Transmitter minimum output power for Single Carrier. 44
4.2.5.1.1 Definition. 44
4.2.5.1.2 Limits . 44
4.2.5.1.3 Conformance . 44
4.2.5.2 Transmitter minimum output power for Carrier Aggregation (DL CA and UL CA) . 45
4.2.5.2.1 Definition. 45
4.2.5.2.2 Limits . 45
4.2.5.2.3 Conformance . 45
4.2.5.3 Transmitter minimum output power for UL-MIMO . 45
4.2.5.3.1 Definition. 45
4.2.5.3.2 Limits . 45
4.2.5.3.3 Conformance . 46
4.2.5.4 Transmitter minimum output power for category NB1 . 46
4.2.5.4.1 Definition. 46
4.2.5.4.2 Limits . 46
4.2.5.4.3 Conformance . 46
4.2.6 Receiver Adjacent Channel Selectivity (ACS) . 46
4.2.6.1 Receiver Adjacent Channel Selectivity (ACS) for Single Carrier . 46
4.2.6.1.1 Definition. 46
4.2.6.1.2 Limits . 46
4.2.6.1.3 Conformance . 47
4.2.6.2 Receiver Adjacent Channel Selectivity (ACS) for Carrier Aggregation in DL-only bands . 47
4.2.6.2.1 Definition. 47
4.2.6.2.2 Limits . 48
4.2.6.2.3 Conformance . 48
4.2.6.3 Receiver Adjacent Channel Selectivity (ACS) for category NB1 . 49
4.2.6.3.1 Definition. 49
4.2.6.3.2 Limits . 49
4.2.6.3.3 Conformance . 49
4.2.7 Receiver Blocking Characteristics . 49
4.2.7.1 Receiver Blocking Characteristics for Single Carrier . 49
4.2.7.1.1 Definition. 49
4.2.7.1.2 Limits . 49
4.2.7.1.3 Conformance . 51
4.2.7.2 Receiver Blocking Characteristics for Carrier Aggregation in DL-only bands . 51
ETSI

---------------------- Page: 4 ----------------------
5 ETSI EN 301 908-13 V13.2.1 (2022-02)
4.2.7.2.1 Definition. 51
4.2.7.2.2 Limits . 52
4.2.7.2.3 Conformance . 54
4.2.7.3 Receiver Blocking Characteristics for category NB1 . 55
4.2.7.3.1 Definition. 55
4.2.7.3.2 Limits . 55
4.2.7.3.3 Conformance . 56
4.2.8 Receiver Spurious Response . 56
4.2.8.1 Receiver Spurious Response for Single Carrier . 56
4.2.8.1.1 Definition. 56
4.2.8.1.2 Limits . 57
4.2.8.1.3 Conformance . 57
4.2.8.2 Receiver Spurious Response for Carrier Aggregation in DL-only bands . 57
4.2.8.2.1 Definition. 57
4.2.8.2.2 Limits . 57
4.2.8.2.3 Conformance . 57
4.2.8.3 Receiver Spurious Response for category NB1 . 57
4.2.8.3.1 Definition. 57
4.2.8.3.2 Limits . 58
4.2.8.3.3 Conformance . 58
4.2.9 Receiver Intermodulation Characteristic . 58
4.2.9.1 Receiver Intermodulation Characteristics for Single Carrier . 58
4.2.9.1.1 Definition. 58
4.2.9.1.2 Limits . 58
4.2.9.1.3 Conformance . 59
4.2.9.2 Receiver Intermodulation Characteristics for Carrier Aggregation in DL-only bands . 59
4.2.9.2.1 Definition. 59
4.2.9.2.2 Limits . 59
4.2.9.2.3 Conformance . 60
4.2.9.3 Receiver Intermodulation Characteristics for category NB1 . 60
4.2.9.3.1 Definition. 60
4.2.9.3.2 Limits . 60
4.2.9.3.3 Conformance . 60
4.2.10 Receiver Spurious Emissions . 61
4.2.10.1 Receiver Spurious Emissions for Single Carrier . 61
4.2.10.1.1 Definition. 61
4.2.10.1.2 Limits . 61
4.2.10.1.3 Conformance . 61
4.2.10.2 Receiver Spurious Emissions in DL-only bands . 61
4.2.10.2.1 Definition. 61
4.2.10.2.2 Limits . 61
4.2.10.2.3 Conformance . 61
4.2.11 Transmitter Adjacent Channel Leakage Power Ratio . 62
4.2.11.1 Transmitter adjacent channel leakage power ratio for Single Carrier . 62
4.2.11.1.1 Definition. 62
4.2.11.1.2 Limits . 62
4.2.11.1.3 Conformance . 63
4.2.11.2 Transmitter adjacent channel leakage power ratio for Carrier Aggregation (DL CA and UL CA). 63
4.2.11.2.1 Definition. 63
4.2.11.2.2 Limits for CA UTRA . 64
4.2.11.2.3 Limits for CA EUTRA . 65
4.2.11.2.4 Conformance . 65
4.2.11.3 Transmitter adjacent channel leakage power ratio for UL-MIMO . 65
4.2.11.3.1 Definition. 65
4.2.11.3.2 Limits . 6
...

SLOVENSKI STANDARD
SIST EN 301 908-13 V13.2.1:2022
01-april-2022
Celična omrežja IMT - Harmonizirani standard za dostop do radijskega spektra -
13. del: Uporabniška oprema za razviti prizemni radijski dostop za UMTS (E-UTRA)
IMT cellular networks - Harmonised Standard for access to radio spectrum - Part 13:
Evolved Universal Terrestrial Radio Access (E-UTRA) User Equipment (UE)
Ta slovenski standard je istoveten z: ETSI EN 301 908-13 V13.2.1 (2022-02)
ICS:
33.060.99 Druga oprema za radijske Other equipment for
komunikacije radiocommunications
33.070.99 Druge mobilne storitve Other mobile services
SIST EN 301 908-13 V13.2.1:2022 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 301 908-13 V13.2.1:2022

---------------------- Page: 2 ----------------------
SIST EN 301 908-13 V13.2.1:2022
ETSI EN 301 908-13 V13.2.1 (2022-02)






HARMONISED EUROPEAN STANDARD
IMT cellular networks;
Harmonised Standard for access to radio spectrum;
Part 13: Evolved Universal Terrestrial Radio Access (E-UTRA)
User Equipment (UE)

---------------------- Page: 3 ----------------------
SIST EN 301 908-13 V13.2.1:2022
 2 ETSI EN 301 908-13 V13.2.1 (2022-02)

Reference
REN/MSG-TFES-1137
Keywords
3G, 3GPP, cellular, digital, E-UTRA, IMT, LTE,
LTE-Advanced, mobile, radio, regulation, UMTS

ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Notice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.
No recommendation as to products and services or vendors is made or should be implied.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.

Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2022.
All rights reserved.

ETSI

---------------------- Page: 4 ----------------------
SIST EN 301 908-13 V13.2.1:2022
 3 ETSI EN 301 908-13 V13.2.1 (2022-02)
Contents
Intellectual Property Rights . 11
Foreword . 11
Modal verbs terminology . 12
Introduction . 12
1 Scope . 13
2 References . 16
2.1 Normative references . 16
2.2 Informative references . 17
3 Definition of terms, symbols and abbreviations . 18
3.1 Terms . 18
3.2 Symbols . 21
3.3 Abbreviations . 23
4 Technical requirements specifications . 24
4.1 Environmental profile . 24
4.2 Conformance requirements . 24
4.2.0 General . 24
4.2.1 Introduction. 24
4.2.2 Transmitter Maximum Output Power . 25
4.2.2.1 Transmitter maximum output power for Single Carrier . 25
4.2.2.1.1 Definition. 25
4.2.2.1.2 Limits . 26
4.2.2.1.3 Conformance . 26
4.2.2.2 Transmitter output power for Carrier Aggregation (DL CA and UL CA) . 26
4.2.2.2.1 Definition. 26
4.2.2.2.2 Limits . 27
4.2.2.2.3 Conformance . 28
4.2.2.3 Transmitter output power for UL-MIMO . 28
4.2.2.3.1 Definition. 28
4.2.2.3.2 Limits . 28
4.2.2.3.3 Conformance . 28
4.2.2.4 Transmitter output power for category NB1 . 29
4.2.2.4.1 Definition. 29
4.2.2.4.2 Limits . 29
4.2.2.4.3 Conformance . 29
4.2.2.5 Transmitter output power for UE category M1 . 29
4.2.2.5.1 Definition. 29
4.2.2.5.2 Limits . 29
4.2.2.5.3 Conformance . 30
4.2.3 Transmitter Spectrum Emission Mask . 30
4.2.3.1 Transmitter spectrum emission mask for Single Carrier . 30
4.2.3.1.1 Definition. 30
4.2.3.1.2 Limits . 30
4.2.3.1.3 Conformance . 31
4.2.3.2 Transmitter spectrum emission mask for Carrier Aggregation (DL CA and UL CA) . 31
4.2.3.2.1 Definition. 31
4.2.3.2.2 Limits . 31
4.2.3.2.3 Conformance . 32
4.2.3.3 Transmitter spectrum emission mask for UL-MIMO . 32
4.2.3.3.1 Definition. 32
4.2.3.3.2 Limits . 32
4.2.3.3.3 Conformance . 32
4.2.3.4 Transmitter spectrum emission mask for Multi-Cluster PUSCH within a component carrier . 33
4.2.3.4.1 Definition. 33
4.2.3.4.2 Limits . 33
ETSI

---------------------- Page: 5 ----------------------
SIST EN 301 908-13 V13.2.1:2022
 4 ETSI EN 301 908-13 V13.2.1 (2022-02)
4.2.3.4.3 Conformance . 33
4.2.3.5 Transmitter spectrum emission mask for category NB1 . 33
4.2.3.5.1 Definition. 33
4.2.3.5.2 Limits . 33
4.2.3.5.3 Conformance . 33
4.2.4 Transmitter Spurious Emissions . 33
4.2.4.1 Transmitter spurious emissions for Single Carrier . 33
4.2.4.1.1 Definition. 33
4.2.4.1.2 Limits . 33
4.2.4.1.3 Conformance . 37
4.2.4.2 Transmitter spurious emissions for Carrier Aggregation (DL CA and UL CA) . 37
4.2.4.2.1 Definition. 37
4.2.4.2.2 Limits . 38
4.2.4.2.3 Conformance . 43
4.2.4.3 Transmitter spurious emissions for UL-MIMO . 43
4.2.4.3.1 Definition. 43
4.2.4.3.2 Limits . 43
4.2.4.3.3 Conformance . 43
4.2.4.4 Transmitter spurious emissions for Multi-Cluster PUSCH within a component carrier . 43
4.2.4.4.1 Definition. 43
4.2.4.4.2 Limits . 43
4.2.4.4.3 Conformance . 44
4.2.4.5 Transmitter spurious emissions for category NB1 . 44
4.2.4.5.1 Definition. 44
4.2.4.5.2 Limits . 44
4.2.4.5.3 Conformance . 44
4.2.5 Transmitter Minimum Output Power . 44
4.2.5.1 Transmitter minimum output power for Single Carrier. 44
4.2.5.1.1 Definition. 44
4.2.5.1.2 Limits . 44
4.2.5.1.3 Conformance . 44
4.2.5.2 Transmitter minimum output power for Carrier Aggregation (DL CA and UL CA) . 45
4.2.5.2.1 Definition. 45
4.2.5.2.2 Limits . 45
4.2.5.2.3 Conformance . 45
4.2.5.3 Transmitter minimum output power for UL-MIMO . 45
4.2.5.3.1 Definition. 45
4.2.5.3.2 Limits . 45
4.2.5.3.3 Conformance . 46
4.2.5.4 Transmitter minimum output power for category NB1 . 46
4.2.5.4.1 Definition. 46
4.2.5.4.2 Limits . 46
4.2.5.4.3 Conformance . 46
4.2.6 Receiver Adjacent Channel Selectivity (ACS) . 46
4.2.6.1 Receiver Adjacent Channel Selectivity (ACS) for Single Carrier . 46
4.2.6.1.1 Definition. 46
4.2.6.1.2 Limits . 46
4.2.6.1.3 Conformance . 47
4.2.6.2 Receiver Adjacent Channel Selectivity (ACS) for Carrier Aggregation in DL-only bands . 47
4.2.6.2.1 Definition. 47
4.2.6.2.2 Limits . 48
4.2.6.2.3 Conformance . 48
4.2.6.3 Receiver Adjacent Channel Selectivity (ACS) for category NB1 . 49
4.2.6.3.1 Definition. 49
4.2.6.3.2 Limits . 49
4.2.6.3.3 Conformance . 49
4.2.7 Receiver Blocking Characteristics . 49
4.2.7.1 Receiver Blocking Characteristics for Single Carrier . 49
4.2.7.1.1 Definition. 49
4.2.7.1.2 Limits . 49
4.2.7.1.3 Conformance . 51
4.2.7.2 Receiver Blocking Characteristics for Carrier Aggregation in DL-only bands . 51
ETSI

---------------------- Page: 6 ----------------------
SIST EN 301 908-13 V13.2.1:2022
 5 ETSI EN 301 908-13 V13.2.1 (2022-02)
4.2.7.2.1 Definition. 51
4.2.7.2.2 Limits . 52
4.2.7.2.3 Conformance . 54
4.2.7.3 Receiver Blocking Characteristics for category NB1 . 55
4.2.7.3.1 Definition. 55
4.2.7.3.2 Limits . 55
4.2.7.3.3 Conformance . 56
4.2.8 Receiver Spurious Response . 56
4.2.8.1 Receiver Spurious Response for Single Carrier . 56
4.2.8.1.1 Definition. 56
4.2.8.1.2 Limits . 57
4.2.8.1.3 Conformance . 57
4.2.8.2 Receiver Spurious Response for Carrier Aggregation in DL-only bands . 57
4.2.8.2.1 Definition. 57
4.2.8.2.2 Limits . 57
4.2.8.2.3 Conformance . 57
4.2.8.3 Receiver Spurious Response for category NB1 . 57
4.2.8.3.1 Definition. 57
4.2.8.3.2 Limits . 58
4.2.8.3.3 Conformance . 58
4.2.9 Receiver Intermodulation Characteristic . 58
4.2.9.1 Receiver Intermodulation Characteristics for Single Carrier . 58
4.2.9.1.1 Definition. 58
4.2.9.1.2 Limits . 58
4.2.9.1.3 Conformance . 59
4.2.9.2 Receiver Intermodulation Characteristics for Carrier Aggregation in DL-only bands . 59
4.2.9.2.1 Definition. 59
4.2.9.2.2 Limits . 59
4.2.9.2.3 Conformance . 60
4.2.9.3 Receiver Intermodulation Characteristics for category NB1 . 60
4.2.9.3.1 Definition. 60
4.2.9.3.2 Limits . 60
4.2.9.3.3 Conformance . 60
4.2.10 Receiver Spurious Emissions . 61
4.2.10.1 Receiver Spurious Emissions for Single Carrier . 61
4.2.10.1.1 Definition. 61
4.2.10.1.2 Limits . 61
4.2.10.1.3 Conformance . 61
4.2.10.2 Receiver Spurious Emissions in DL-only bands . 61
4.2.10.2.1 Definition. 61
4.2.10.2.2 Limits . 61
4.2.10.2.3 Conformance . 61
4.2.11 Transmitter Adjacent Channel Leakage Power Ratio . 62
4.2.11.1 Transmitter adjacent channel leakage power ratio for Single Carrier . 62
4.2.11.1.1 Definition. 62
4.2.11.1.2 Limits . 62
4.2.11.1.3 Conformance . 63
4.2.11.2 Transmitter adjacent channel leakage power ratio for Carrier Aggregation (DL CA and UL CA). 63
4.2.11.2.1 Defini
...

Draft ETSI EN 301 908-13 V13.2.0 (2021-11)






HARMONISED EUROPEAN STANDARD
IMT cellular networks;
Harmonised Standard for access to radio spectrum;
Part 13: Evolved Universal Terrestrial Radio Access (E-UTRA)
User Equipment (UE)

---------------------- Page: 1 ----------------------
2 Draft ETSI EN 301 908-13 V13.2.0 (2021-11)

Reference
REN/MSG-TFES-1137
Keywords
3G, 3GPP, cellular, digital, E-UTRA, IMT, LTE,
LTE-Advanced, mobile, radio, regulation, UMTS

ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Notice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.
No recommendation as to products and services or vendors is made or should be implied.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.

Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2021.
All rights reserved.

ETSI

---------------------- Page: 2 ----------------------
3 Draft ETSI EN 301 908-13 V13.2.0 (2021-11)
Contents
Intellectual Property Rights . 11
Foreword . 11
Modal verbs terminology . 12
Introduction . 12
1 Scope . 13
2 References . 16
2.1 Normative references . 16
2.2 Informative references . 17
3 Definition of terms, symbols and abbreviations . 18
3.1 Terms . 18
3.2 Symbols . 21
3.3 Abbreviations . 23
4 Technical requirements specifications . 24
4.1 Environmental profile . 24
4.2 Conformance requirements . 24
4.2.0 General . 24
4.2.1 Introduction. 24
4.2.2 Transmitter Maximum Output Power . 25
4.2.2.1 Transmitter maximum output power for Single Carrier . 25
4.2.2.1.1 Definition. 25
4.2.2.1.2 Limits . 26
4.2.2.1.3 Conformance . 26
4.2.2.2 Transmitter output power for Carrier Aggregation (DL CA and UL CA) . 26
4.2.2.2.1 Definition. 26
4.2.2.2.2 Limits . 27
4.2.2.2.3 Conformance . 28
4.2.2.3 Transmitter output power for UL-MIMO . 28
4.2.2.3.1 Definition. 28
4.2.2.3.2 Limits . 28
4.2.2.3.3 Conformance . 28
4.2.2.4 Transmitter output power for category NB1 . 29
4.2.2.4.1 Definition. 29
4.2.2.4.2 Limits . 29
4.2.2.4.3 Conformance . 29
4.2.2.5 Transmitter output power for UE category M1 . 29
4.2.2.5.1 Definition. 29
4.2.2.5.2 Limits . 29
4.2.2.5.3 Conformance . 30
4.2.3 Transmitter Spectrum Emission Mask . 30
4.2.3.1 Transmitter spectrum emission mask for Single Carrier . 30
4.2.3.1.1 Definition. 30
4.2.3.1.2 Limits . 30
4.2.3.1.3 Conformance . 31
4.2.3.2 Transmitter spectrum emission mask for Carrier Aggregation (DL CA and UL CA) . 31
4.2.3.2.1 Definition. 31
4.2.3.2.2 Limits . 31
4.2.3.2.3 Conformance . 33
4.2.3.3 Transmitter spectrum emission mask for UL-MIMO . 33
4.2.3.3.1 Definition. 33
4.2.3.3.2 Limits . 33
4.2.3.3.3 Conformance . 33
4.2.3.4 Transmitter spectrum emission mask for Multi-Cluster PUSCH within a component carrier . 33
4.2.3.4.1 Definition. 33
4.2.3.4.2 Limits . 33
ETSI

---------------------- Page: 3 ----------------------
4 Draft ETSI EN 301 908-13 V13.2.0 (2021-11)
4.2.3.4.3 Conformance . 33
4.2.3.5 Transmitter spectrum emission mask for category NB1 . 33
4.2.3.5.1 Definition. 33
4.2.3.5.2 Limits . 33
4.2.3.5.3 Conformance . 34
4.2.4 Transmitter Spurious Emissions . 34
4.2.4.1 Transmitter spurious emissions for Single Carrier . 34
4.2.4.1.1 Definition. 34
4.2.4.1.2 Limits . 34
4.2.4.1.3 Conformance . 38
4.2.4.2 Transmitter spurious emissions for Carrier Aggregation (DL CA and UL CA) . 38
4.2.4.2.1 Definition. 38
4.2.4.2.2 Limits . 38
4.2.4.2.3 Conformance . 44
4.2.4.3 Transmitter spurious emissions for UL-MIMO . 44
4.2.4.3.1 Definition. 44
4.2.4.3.2 Limits . 44
4.2.4.3.3 Conformance . 44
4.2.4.4 Transmitter spurious emissions for Multi-Cluster PUSCH within a component carrier . 44
4.2.4.4.1 Definition. 44
4.2.4.4.2 Limits . 44
4.2.4.4.3 Conformance . 45
4.2.4.5 Transmitter spurious emissions for category NB1 . 45
4.2.4.5.1 Definition. 45
4.2.4.5.2 Limits . 45
4.2.4.5.3 Conformance . 45
4.2.5 Transmitter Minimum Output Power . 45
4.2.5.1 Transmitter minimum output power for Single Carrier. 45
4.2.5.1.1 Definition. 45
4.2.5.1.2 Limits . 45
4.2.5.1.3 Conformance . 45
4.2.5.2 Transmitter minimum output power for Carrier Aggregation (DL CA and UL CA) . 46
4.2.5.2.1 Definition. 46
4.2.5.2.2 Limits . 46
4.2.5.2.3 Conformance . 46
4.2.5.3 Transmitter minimum output power for UL-MIMO . 46
4.2.5.3.1 Definition. 46
4.2.5.3.2 Limits . 46
4.2.5.3.3 Conformance . 47
4.2.5.4 Transmitter minimum output power for category NB1 . 47
4.2.5.4.1 Definition. 47
4.2.5.4.2 Limits . 47
4.2.5.4.3 Conformance . 47
4.2.6 Receiver Adjacent Channel Selectivity (ACS) . 47
4.2.6.1 Receiver Adjacent Channel Selectivity (ACS) for Single Carrier . 47
4.2.6.1.1 Definition. 47
4.2.6.1.2 Limits . 47
4.2.6.1.3 Conformance . 48
4.2.6.2 Receiver Adjacent Channel Selectivity (ACS) for Carrier Aggregation in DL-only bands . 48
4.2.6.2.1 Definition. 48
4.2.6.2.2 Limits . 49
4.2.6.2.3 Conformance . 49
4.2.6.3 Receiver Adjacent Channel Selectivity (ACS) for category NB1 . 50
4.2.6.3.1 Definition. 50
4.2.6.3.2 Limits . 50
4.2.6.3.3 Conformance . 50
4.2.7 Receiver Blocking Characteristics . 50
4.2.7.1 Receiver Blocking Characteristics for Single Carrier . 50
4.2.7.1.1 Definition. 50
4.2.7.1.2 Limits . 50
4.2.7.1.3 Conformance . 52
4.2.7.2 Receiver Blocking Characteristics for Carrier Aggregation in DL-only bands . 52
ETSI

---------------------- Page: 4 ----------------------
5 Draft ETSI EN 301 908-13 V13.2.0 (2021-11)
4.2.7.2.1 Definition. 52
4.2.7.2.2 Limits . 53
4.2.7.2.3 Conformance . 55
4.2.7.3 Receiver Blocking Characteristics for category NB1 . 56
4.2.7.3.1 Definition. 56
4.2.7.3.2 Limits . 56
4.2.7.3.3 Conformance . 57
4.2.8 Receiver Spurious Response . 58
4.2.8.1 Receiver Spurious Response for Single Carrier . 58
4.2.8.1.1 Definition. 58
4.2.8.1.2 Limits . 58
4.2.8.1.3 Conformance . 58
4.2.8.2 Receiver Spurious Response for Carrier Aggregation in DL-only bands . 58
4.2.8.2.1 Definition. 58
4.2.8.2.2 Limits . 58
4.2.8.2.3 Conformance . 58
4.2.8.3 Receiver Spurious Response for category NB1 . 59
4.2.8.3.1 Definition. 59
4.2.8.3.2 Limits . 59
4.2.8.3.3 Conformance . 59
4.2.9 Receiver Intermodulation Characteristic . 59
4.2.9.1 Receiver Intermodulation Characteristics for Single Carrier . 59
4.2.9.1.1 Definition. 59
4.2.9.1.2 Limits . 59
4.2.9.1.3 Conformance . 60
4.2.9.2 Receiver Intermodulation Characteristics for Carrier Aggregation in DL-only bands . 60
4.2.9.2.1 Definition. 60
4.2.9.2.2 Limits . 60
4.2.9.2.3 Conformance . 61
4.2.9.3 Receiver Intermodulation Characteristics for category NB1 . 61
4.2.9.3.1 Definition. 61
4.2.9.3.2 Limits . 61
4.2.9.3.3 Conformance . 61
4.2.10 Receiver Spurious Emissions . 62
4.2.10.1 Receiver Spurious Emissions for Single Carrier . 62
4.2.10.1.1 Definition. 62
4.2.10.1.2 Limits . 62
4.2.10.1.3 Conformance . 62
4.2.10.2 Receiver Spurious Emissions in DL-only bands . 62
4.2.10.2.1 Definition. 62
4.2.10.2.2 Limits . 62
4.2.10.2.3 Conformance . 62
4.2.11 Transmitter Adjacent Channel Leakage Power Ratio . 63
4.2.11.1 Transmitter adjacent channel leakage power ratio for Single Carrier . 63
4.2.11.1.1 Definition. 63
4.2.11.1.2 Limits . 63
4.2.11.1.3 Conformance . 64
4.2.11.2 Transmitter adjacent channel leakage power ratio for Carrier Aggregation (DL CA and UL CA). 64
4.2.11.2.1 Definition. 64
4.2.11.2.2 Limits for CA UTRA . 65
4.2.11.2.3 Limits for CA EUTRA . 66
4.2.11.2.4 Conformance . 66
4.2.11.3 Transmitter adjacent channel leakage power ratio for UL-MIMO . 66
4.2.11.3.1 Definition. 66
4.2.11.3.2 Limits .
...

SLOVENSKI STANDARD
oSIST prEN 301 908-13 V13.2.0:2022
01-januar-2022
Celična omrežja IMT - Harmonizirani standard za dostop do radijskega spektra -
13. del: Uporabniška oprema za razviti prizemni radijski dostop za UMTS (E-UTRA)
IMT cellular networks - Harmonised Standard for access to radio spectrum - Part 13:
Evolved Universal Terrestrial Radio Access (E-UTRA) User Equipment (UE)
Ta slovenski standard je istoveten z: ETSI EN 301 908-13 V13.2.0 (2021-11)
ICS:
33.060.99 Druga oprema za radijske Other equipment for
komunikacije radiocommunications
33.070.99 Druge mobilne storitve Other mobile services
oSIST prEN 301 908-13 V13.2.0:2022 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 301 908-13 V13.2.0:2022

---------------------- Page: 2 ----------------------
oSIST prEN 301 908-13 V13.2.0:2022
Draft ETSI EN 301 908-13 V13.2.0 (2021-11)






HARMONISED EUROPEAN STANDARD
IMT cellular networks;
Harmonised Standard for access to radio spectrum;
Part 13: Evolved Universal Terrestrial Radio Access (E-UTRA)
User Equipment (UE)

---------------------- Page: 3 ----------------------
oSIST prEN 301 908-13 V13.2.0:2022
 2 Draft ETSI EN 301 908-13 V13.2.0 (2021-11)

Reference
REN/MSG-TFES-1137
Keywords
3G, 3GPP, cellular, digital, E-UTRA, IMT, LTE,
LTE-Advanced, mobile, radio, regulation, UMTS

ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Notice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.
No recommendation as to products and services or vendors is made or should be implied.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.

Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2021.
All rights reserved.

ETSI

---------------------- Page: 4 ----------------------
oSIST prEN 301 908-13 V13.2.0:2022
 3 Draft ETSI EN 301 908-13 V13.2.0 (2021-11)
Contents
Intellectual Property Rights . 11
Foreword . 11
Modal verbs terminology . 12
Introduction . 12
1 Scope . 13
2 References . 16
2.1 Normative references . 16
2.2 Informative references . 17
3 Definition of terms, symbols and abbreviations . 18
3.1 Terms . 18
3.2 Symbols . 21
3.3 Abbreviations . 23
4 Technical requirements specifications . 24
4.1 Environmental profile . 24
4.2 Conformance requirements . 24
4.2.0 General . 24
4.2.1 Introduction. 24
4.2.2 Transmitter Maximum Output Power . 25
4.2.2.1 Transmitter maximum output power for Single Carrier . 25
4.2.2.1.1 Definition. 25
4.2.2.1.2 Limits . 26
4.2.2.1.3 Conformance . 26
4.2.2.2 Transmitter output power for Carrier Aggregation (DL CA and UL CA) . 26
4.2.2.2.1 Definition. 26
4.2.2.2.2 Limits . 27
4.2.2.2.3 Conformance . 28
4.2.2.3 Transmitter output power for UL-MIMO . 28
4.2.2.3.1 Definition. 28
4.2.2.3.2 Limits . 28
4.2.2.3.3 Conformance . 28
4.2.2.4 Transmitter output power for category NB1 . 29
4.2.2.4.1 Definition. 29
4.2.2.4.2 Limits . 29
4.2.2.4.3 Conformance . 29
4.2.2.5 Transmitter output power for UE category M1 . 29
4.2.2.5.1 Definition. 29
4.2.2.5.2 Limits . 29
4.2.2.5.3 Conformance . 30
4.2.3 Transmitter Spectrum Emission Mask . 30
4.2.3.1 Transmitter spectrum emission mask for Single Carrier . 30
4.2.3.1.1 Definition. 30
4.2.3.1.2 Limits . 30
4.2.3.1.3 Conformance . 31
4.2.3.2 Transmitter spectrum emission mask for Carrier Aggregation (DL CA and UL CA) . 31
4.2.3.2.1 Definition. 31
4.2.3.2.2 Limits . 31
4.2.3.2.3 Conformance . 33
4.2.3.3 Transmitter spectrum emission mask for UL-MIMO . 33
4.2.3.3.1 Definition. 33
4.2.3.3.2 Limits . 33
4.2.3.3.3 Conformance . 33
4.2.3.4 Transmitter spectrum emission mask for Multi-Cluster PUSCH within a component carrier . 33
4.2.3.4.1 Definition. 33
4.2.3.4.2 Limits . 33
ETSI

---------------------- Page: 5 ----------------------
oSIST prEN 301 908-13 V13.2.0:2022
 4 Draft ETSI EN 301 908-13 V13.2.0 (2021-11)
4.2.3.4.3 Conformance . 33
4.2.3.5 Transmitter spectrum emission mask for category NB1 . 33
4.2.3.5.1 Definition. 33
4.2.3.5.2 Limits . 33
4.2.3.5.3 Conformance . 34
4.2.4 Transmitter Spurious Emissions . 34
4.2.4.1 Transmitter spurious emissions for Single Carrier . 34
4.2.4.1.1 Definition. 34
4.2.4.1.2 Limits . 34
4.2.4.1.3 Conformance . 38
4.2.4.2 Transmitter spurious emissions for Carrier Aggregation (DL CA and UL CA) . 38
4.2.4.2.1 Definition. 38
4.2.4.2.2 Limits . 38
4.2.4.2.3 Conformance . 44
4.2.4.3 Transmitter spurious emissions for UL-MIMO . 44
4.2.4.3.1 Definition. 44
4.2.4.3.2 Limits . 44
4.2.4.3.3 Conformance . 44
4.2.4.4 Transmitter spurious emissions for Multi-Cluster PUSCH within a component carrier . 44
4.2.4.4.1 Definition. 44
4.2.4.4.2 Limits . 44
4.2.4.4.3 Conformance . 45
4.2.4.5 Transmitter spurious emissions for category NB1 . 45
4.2.4.5.1 Definition. 45
4.2.4.5.2 Limits . 45
4.2.4.5.3 Conformance . 45
4.2.5 Transmitter Minimum Output Power . 45
4.2.5.1 Transmitter minimum output power for Single Carrier. 45
4.2.5.1.1 Definition. 45
4.2.5.1.2 Limits . 45
4.2.5.1.3 Conformance . 45
4.2.5.2 Transmitter minimum output power for Carrier Aggregation (DL CA and UL CA) . 46
4.2.5.2.1 Definition. 46
4.2.5.2.2 Limits . 46
4.2.5.2.3 Conformance . 46
4.2.5.3 Transmitter minimum output power for UL-MIMO . 46
4.2.5.3.1 Definition. 46
4.2.5.3.2 Limits . 46
4.2.5.3.3 Conformance . 47
4.2.5.4 Transmitter minimum output power for category NB1 . 47
4.2.5.4.1 Definition. 47
4.2.5.4.2 Limits . 47
4.2.5.4.3 Conformance . 47
4.2.6 Receiver Adjacent Channel Selectivity (ACS) . 47
4.2.6.1 Receiver Adjacent Channel Selectivity (ACS) for Single Carrier . 47
4.2.6.1.1 Definition. 47
4.2.6.1.2 Limits . 47
4.2.6.1.3 Conformance . 48
4.2.6.2 Receiver Adjacent Channel Selectivity (ACS) for Carrier Aggregation in DL-only bands . 48
4.2.6.2.1 Definition. 48
4.2.6.2.2 Limits . 49
4.2.6.2.3 Conformance . 49
4.2.6.3 Receiver Adjacent Channel Selectivity (ACS) for category NB1 . 50
4.2.6.3.1 Definition. 50
4.2.6.3.2 Limits . 50
4.2.6.3.3 Conformance . 50
4.2.7 Receiver Blocking Characteristics . 50
4.2.7.1 Receiver Blocking Characteristics for Single Carrier . 50
4.2.7.1.1 Definition. 50
4.2.7.1.2 Limits . 50
4.2.7.1.3 Conformance . 52
4.2.7.2 Receiver Blocking Characteristics for Carrier Aggregation in DL-only bands . 52
ETSI

---------------------- Page: 6 ----------------------
oSIST prEN 301 908-13 V13.2.0:2022
 5 Draft ETSI EN 301 908-13 V13.2.0 (2021-11)
4.2.7.2.1 Definition. 52
4.2.7.2.2 Limits . 53
4.2.7.2.3 Conformance . 55
4.2.7.3 Receiver Blocking Characteristics for category NB1 . 56
4.2.7.3.1 Definition. 56
4.2.7.3.2 Limits . 56
4.2.7.3.3 Conformance . 57
4.2.8 Receiver Spurious Response . 58
4.2.8.1 Receiver Spurious Response for Single Carrier . 58
4.2.8.1.1 Definition. 58
4.2.8.1.2 Limits . 58
4.2.8.1.3 Conformance . 58
4.2.8.2 Receiver Spurious Response for Carrier Aggregation in DL-only bands . 58
4.2.8.2.1 Definition. 58
4.2.8.2.2 Limits . 58
4.2.8.2.3 Conformance . 58
4.2.8.3 Receiver Spurious Response for category NB1 . 59
4.2.8.3.1 Definition. 59
4.2.8.3.2 Limits . 59
4.2.8.3.3 Conformance . 59
4.2.9 Receiver Intermodulation Characteristic . 59
4.2.9.1 Receiver Intermodulation Characteristics for Single Carrier . 59
4.2.9.1.1 Definition. 59
4.2.9.1.2 Limits . 59
4.2.9.1.3 Conformance . 60
4.2.9.2 Receiver Intermodulation Characteristics for Carrier Aggregation in DL-only bands . 60
4.2.9.2.1 Definition. 60
4.2.9.2.2 Limits . 60
4.2.9.2.3 Conformance . 61
4.2.9.3 Receiver Intermodulation Characteristics for category NB1 . 61
4.2.9.3.1 Definition. 61
4.2.9.3.2 Limits . 61
4.2.9.3.3 Conformance . 61
4.2.10 Receiver Spurious Emissions . 62
4.2.10.1 Receiver Spurious Emissions for Single Carrier . 62
4.2.10.1.1 Definition. 62
4.2.10.1.2 Limits . 62
4.2.10.1.3 Conformance . 62
4.2.10.2 Receiver Spurious Emissions in DL-only bands . 62
4.2.10.2.1 Definition. 62
4.2.10.2.2 Limits . 62
4.2.10.2.3 Conformance . 62
4.2.11 Transmitter Adjacent Channel Leakage Power Ratio . 63
4.2.11.1 Transmitter adjacent channel leakage power ratio for Single Carrier . 63
4.2.11.1.1 Definition. 63
4.2.11.1.2 Limits . 63
4.2.11.1.3 Conformance . 64
4.2.11.2 Transmitter adjacent channel leakage power ratio for Carrier Aggrega
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.