SIST EN ISO 18082:2014/A1:2018

SLOVENSKI STANDARD
SIST EN ISO 18082:2014/A1:2018
01-marec-2018
$QHVWH]LMVNDLQGLKDOQDRSUHPD0HUHQL]NRWODþQLKSULNOMXþNRY]QDYRMHPNLVHQH
PHQMDMR]DGHOR]PHGLFLQVNLPLSOLQL1,67'RSROQLOR$,62$PG

Anaesthetic and respiratory equipment - Dimensions of non-interchangeable screw-
threaded (NIST) low-pressure connectors for medical gases - Amendment 1 (ISO
18082:2014/Amd 1:2017)
Anästhesie- und Beatmungsgeräte - Maße von nichtverwechselbaren
Verbindungsstücken mit Schraubgewinde (NIST) für niedrigen Druck zur Verwendung
mit medizinischen Gasen - Änderung 1 (ISO 18082:2014/Amd 1:2017)
Matériel respiratoire et anesthésique - Raccords basse pression à tête filetée non
interchangeables (NIST) pour gaz médicaux - Amendement 1 (ISO 18082:2014/Amd
1:2017)
Ta slovenski standard je istoveten z: EN ISO 18082:2014/A1:2017
ICS:
11.040.10 Anestezijska, respiratorna in Anaesthetic, respiratory and
reanimacijska oprema reanimation equipment
SIST EN ISO 18082:2014/A1:2018 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 18082:2014/A1:2018

---------------------- Page: 2 ----------------------

SIST EN ISO 18082:2014/A1:2018


EN ISO 18082:2014/A1
EUROPEAN STANDARD

NORME EUROPÉENNE

August 2017
EUROPÄISCHE NORM
ICS 11.040.10
English Version

Anaesthetic and respiratory equipment - Dimensions of
non-interchangeable screw-threaded (NIST) low-pressure
connectors for medical gases - Amendment 1 (ISO
18082:2014/Amd 1:2017)
Matériel respiratoire et anesthésique - Raccords basse Anästhesie- und Beatmungsgeräte - Maße von
pression à tête filetée non interchangeables (NIST) nichtverwechselbaren Verbindungsstücken mit
pour gaz médicaux - Amendement 1 (ISO Schraubgewinde (NIST) für niedrigen Druck zur
18082:2014/Amd 1:2017) Verwendung mit medizinischen Gasen - Änderung 1
(ISO 18082:2014/Amd 1:2017)
This amendment A1 modifies the European Standard EN ISO 18082:2014; it was approved by CEN on 1 July 2017.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This amendment exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 18082:2014/A1:2017 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 18082:2014/A1:2018
EN ISO 18082:2014/A1:2017 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 18082:2014/A1:2018
EN ISO 18082:2014/A1:2017 (E)
European foreword
This document (EN ISO 18082:2014/A1:2017) has been prepared by Technical Committee ISO/TC 121
“Anaesthetic and respiratory equipment” in collaboration with Technical Committee CEN/TC 215
“Respiratory and anaesthetic equipment” the secretariat of which is held by BSI.
This Amendment to the European Standard EN ISO 18082:2014 shall be given the status of a national
standard, either by publication of an identical text or by endorsement, at the latest by February 2018,
and conflicting national standards shall be withdrawn at the latest by February 2018.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 18082:2014/Amd 1:2017 has been approved by CEN as EN ISO 18082:2014/A1:2017
without any modification.
3

---------------------- Page: 5 --------------------
...