SIST EN 60286-1:2002

SLOVENSKI STANDARD
SIST EN 60286-1:2002
01-september-2002
Packaging of components for automatic handling - Part 1: Tape packaging of
components with axial leads on continuous tapes (IEC 60286-1:1997)
Packaging of components for automatic handling -- Part 1: Tape packaging of
components with axial leads on continuous tapes
Gurtung und Magazinierung von Bauelementen für automatische Verarbeitung -- Teil 1:
Gurtung von Bauelementen mit axialen Anschlüssen
Emballage des composants pour opérations automatisées -- Partie 1: Emballage des
composants à sorties axiales en bandes continues
Ta slovenski standard je istoveten z: EN 60286-1:1998
ICS:
31.020 Elektronske komponente na Electronic components in
splošno general
55.060 Tulci. Vretena Spools. Bobbins
SIST EN 60286-1:2002 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60286-1:2002

---------------------- Page: 2 ----------------------

SIST EN 60286-1:2002

---------------------- Page: 3 ----------------------

SIST EN 60286-1:2002

---------------------- Page: 4 ----------------------

SIST EN 60286-1:2002

---------------------- Page: 5 ----------------------

SIST EN 60286-1:2002

---------------------- Page: 6 ----------------------

SIST EN 60286-1:2002
NORME
CEI
INTERNATIONALE
IEC
60286-1
INTERNATIONAL
Deuxième édition
STANDARD
Second edition
1997-12
Emballage des composants pour
opérations automatisées –
Partie 1:
Emballage des composants à sorties axiales
en bandes continues
Packaging of components for
automatic handling –
Part 1:
Tape packaging of components with axial leads
on continuous tapes
 IEC 1997 Droits de reproduction réservés  Copyright - all rights reserved
Aucune partie de cette publication ne peut être reproduite ni No part of this publication may be reproduced or utilized in
utilisée sous quelque forme que ce soit et par aucun any form or by any means, electronic or mechanical,
procédé, électronique ou mécanique, y compris la photo- including photocopying and microfilm, without permission in
copie et les microfilms, sans l'accord écrit de l'éditeur. writing from the publisher.
International Electrotechnical Commission 3, rue de Varembé Geneva, Switzerland
Telefax: +41 22 919 0300 e-mail: inmail@iec.ch IEC web site http: //www.iec.ch
CODE PRIX
Commission Electrotechnique Internationale
PRICE CODE J
International Electrotechnical Commission
Pour prix, voir catalogue en vigueur
For price, see current catalogue

---------------------- Page: 7 ----------------------

SIST EN 60286-1:2002
60286-1  IEC:1997 – 3 –
CONTENTS
Page
FOREWORD . 5
Clause
1 General. 7
2 Dimensions . 9
3 Packing. 13
4 Marking. 17

---------------------- Page: 8 ----------------------

SIST EN 60286-1:2002
60286-1  IEC:1997 – 5 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
___________
PACKAGING OF COMPONENTS FOR AUTOMATIC HANDLING –
Part 1: Tape packaging of components with axial leads
on continuous tapes
FOREWORD
1) The IEC (International Electrotechnical Commission) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of the IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, the IEC publishes International Standards. Their preparation is
entrusted to technical committees; any IEC National Committee interested in the subject dealt with may
participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. The IEC collaborates closely with the International Organization
for Standardization (ISO) in accordance with conditions determined by agreement between the two
organizations.
2) The formal decisions or agreements of the IEC on technical matters express, as nearly as possible, an
international consensus of opinion on the relevant subjects since each technical committee has representation
from all interested National Committees.
3) The documents produced have the form of recommendations for international use and are published in the form
of standards, technical reports or guides and they are accepted by the National Committees in that sense.
4) In order to promote international unification, IEC National Committees undertake to apply IEC International
Standards transparently to the maximum extent possible in their national and regional standards. Any
divergence between the IEC Standard and the corresponding national or regional standard shall be clearly
indicated in the latter.
5) The IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with one of its standards.
6) Attention is drawn to the possibility that some of the elements of this International Standard may be the subject
of patent rights. The IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60286-1 has been prepared by IEC technical committee 40:
Capacitors and resistors for electronic equipment.
This second edition cancels and replaces the first edition published in 1980 and constitutes a
technical revision.
The text of this standard is based on the following documents:
FDIS Report on voting
40/917/FDIS 40/1033/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.

---------------------- Page: 9 ----------------------

SIST EN 60286-1:2002
60286-1  IEC:1997 – 7 –
PACKAGING OF COMPONENTS FOR AUTOMATIC HANDLING –
Part 1: Tape packaging of components with axial leads
on continuous tapes
1 General
1.1 Scope
This standard applies to the tape packaging of components with axial leads for use in
electronic equipment. In general, the tape is applied to the component leads.
It covers requirements for taping techniques used with equipment for the preforming of leads,
automatic handling, insertion and other operations, and includes only those dimensions which
are essential to the taping of components intended for the above-mentioned purposes.
1.2 Normative references
The foll
...