SIST EN 301 908-10 V4.1.1:2009
(Main)Electromagnetic compatibility and Radio spectrum Matters (ERM) - Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation cellular networks - Part 10: Harmonized EN for IMT-2000, FDMA/TDMA (DECT) covering essential requirements of article 3.2 of the R&TTE Directive
- Abstract
The present document applies to terminal equipment for IMT-FT. IMT-FT is the Digital Enhanced Cordless Telecommunications (DECT) system being a member of the ITU IMT-2000 family. DECT terminal equipment consists of the following elements:
a) Fixed Part (FP);
b) Portable Part (PP);
c) Cordless Terminal Adapter (CTA);
d) Wireless Relay Station (WRS) (FP and PP combined with repeater functionality);
e) Hybrid Part (HyP) (a PP with capability to act as a FP to provide PP to PP communication).
These radio equipment types are capable of operating in all or any part of the frequency bands given in table 1. The IMT-FT (DECT) service frequency bands for transmitting and receiving for all elements are the parts of the European UMTS spectrum applicable for TDD operation, 1 900 MHz to 1 980 MHz and 2 010 MHz to 2 025 MHz, (see ERC/DEC(99)25 [18] and ERC/DEC(00)01 [19]). NOTE 1: IMT-FT equipment may have a second mode for providing operation also in the DECT band 1 880 MHz to 1 900 MHz. Application of DECT in the band 1 880 MHz to 1 900 MHz is covered by EN 301 406 [i.7]. Details of the DECT Common Interface may be found in EN 300 175 parts 1 to 8 [5] to [12]. Further details of the DECT system may be found in the ETSI Technical Reports, TR 101 178 [i.1] and ETR 043 [i.2]. The present document is intended to cover the provisions of Directive 1999/5/EC (R&TTE Directive) [1] article 3.2, which states that "[…] radio equipment shall be so constructed that it effectively uses the spectrum allocated to terrestrial/space radio communications and orbital resources so as to avoid harmful interference". In addition to the present document, other ENs that specify technical requirements in respect of essential requirements under other parts of article 3 of the R&TTE Directive [1] will apply to equipment within the scope of the present document.
- Status
- Published
- Publication Date
- 16-Aug-2009
- Technical Committee
- MOC - Mobile Communications
- Current Stage
- 6060 - National Implementation/Publication (Adopted Project)
- Start Date
- 29-Jul-2009
- Due Date
- 03-Oct-2009
- Completion Date
- 17-Aug-2009
- Mandate
- M/284
Buy Documents
ETSI EN 301 908-10 V4.1.0 (2009-03) - Electromagnetic compatibility and Radio spectrum Matters (ERM); Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation cellular networks; Part 10: Harmonized EN for IMT-2000, FDMA/TDMA (DECT) covering essential requirements of article 3.2 of the R&TTE Directive
ETSI EN 301 908-10 V4.1.1 (2009-07) - Electromagnetic compatibility and Radio spectrum Matters (ERM); Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation cellular networks; Part 10: Harmonized EN for IMT-2000, FDMA/TDMA (DECT) covering essential requirements of article 3.2 of the R&TTE Directive
SIST EN 301 908-10 V4.1.1:2009 is the Slovenian adoption of the ETSI harmonized European standard for IMT-FT, the DECT member of the IMT-2000 family. It specifies the radio and electromagnetic compatibility requirements for Fixed Part (FP), Portable Part (PP), Cordless Terminal Adapter (CTA), Wireless Relay Station (WRS) and Hybrid Part (HyP) equipment so they use the assigned spectrum without harmful interference. It is written for conformity assessment under article 3.2 of the R&TTE Directive.
What does SIST EN 301 908-10 V4.1.1:2009 specify?
SIST EN 301 908-10 V4.1.1:2009 applies to IMT-FT terminal equipment operating in the DECT bands used for TDD operation, especially 1 900 MHz to 1 980 MHz and 2 010 MHz to 2 025 MHz. The scope also notes a second DECT mode in 1 880 MHz to 1 900 MHz, which is covered by EN 301 406.
The document is organized into scope, references, definitions, technical requirements and test methods. Its test structure follows ISO/IEC 9646-1 and uses a test suite, test groups and test cases model.
| Annex | What it covers |
|---|---|
| Annex A | Summary of the essential requirement articles and the justification of the test cases |
| Annex C | Test Standby Mode and related test messaging used in special equipment testing |
| Annex F | Carrier notations and carrier positions used for band-edge and spectrum tests |
What are the key requirements of SIST EN 301 908-10 V4.1.1:2009?
Frequency, timing and burst behavior
The standard requires declared band edges and supported carriers, and it ties conformance to the declared environmental profile and declared implementation options. That matters because the test plan depends on what the supplier says the equipment can do.
- Clause 4.5.2 limits RF carrier accuracy to tight frequency tolerances, with different extreme-condition limits for FP and PP operation. In practice, this checks oscillator stability and whether the equipment stays on the right channel.
- Clause 4.5.3 controls TDMA timing, including reference timer accuracy, packet timing and jitter. This matters because DECT uses precise slot timing, so poor timing can cause collisions and loss of synchronization.
- Clause 4.5.4 defines the transmission burst shape, attack and release times, minimum and maximum power around packet edges, and idle output power. In practice, this is the transmitter keying test that shows whether the radio turns on and off cleanly.
Modulation, emissions and receiver performance
- Clause 4.5.6 requires Gaussian Frequency Shift Keying (GFSK) with a nominal bandwidth-bit period product and nominal peak deviation. That means the radio must modulate in the DECT way, not with an arbitrary waveform.
- Clause 4.5.7 limits unwanted RF power from modulation, transients, intermodulation and spurious emissions, both in-band and out of band. This matters for coexistence with other radios and for spectrum cleanliness.
- Clause 4.5.8 covers receiver sensitivity, reference Bit Error Ratio (BER) and Frame Error Ratio (FER), interference performance, blocking, receiver intermodulation and spurious emissions when no transmit channel is allocated. In practice, these are the main checks that the receiver can hear weak wanted signals and reject strong unwanted ones.
Special modes and identity features
- Clause 4.5.9 covers intersystem synchronization for FP equipment, including wired synchronization ports and Global Positioning System (GPS) synchronization. This is relevant where several systems must stay aligned.
- Clause 4.5.10 covers equipment identity safeguards, including protection of the International Portable Equipment Identity (IPEI) in PPs and identity message behavior in FPs.
- Clauses 4.5.11 to 4.5.15 cover efficient channel selection and release, WRS behavior, direct PP to PP communication, distributed communications and higher level modulation. These clauses matter for equipment with special DECT modes, because the radio must still follow the required spectrum-sharing behavior.
What terms does SIST EN 301 908-10 V4.1.1:2009 define?
- Fixed Part (FP) - the DECT network-side physical grouping that contains the elements between the local network and the DECT air interface.
- Portable Part (PP) - the user-side physical grouping that contains the elements between the user and the DECT air interface.
- Fixed radio Termination (FT) - the logical functions on the fixed side of the DECT air interface.
- Portable radio Termination (PT) - the logical functions on the portable side of the DECT air interface.
- Radio Fixed Part (RFP) - the physical sub-group of an FP that contains the radio end points connected to one antenna system.
- Wireless Relay Station (WRS) - combined FP and PP functionality with repeater behavior.
- Normal Transmitted Power (NTP) - the average transmitted power over a physical packet, used as the reference for burst and power limits.
Who uses SIST EN 301 908-10 V4.1.1:2009?
Manufacturers of DECT equipment use this standard when designing FP, PP, CTA, WRS and HyP products for the IMT-FT bands. Test laboratories use it to set up conformance tests, including antenna, timing, spectrum and receiver measurements.
Quality, regulatory and compliance teams use it to prepare the supplier declarations, select the applicable test suite, and document special functions such as synchronization ports, direct PP to PP communication and distributed communications. It is also useful for product engineers who need to understand how the DECT air interface is checked in type examination.
Which standards are used with SIST EN 301 908-10 V4.1.1:2009?
- Directive 1999/5/EC - the legal basis for the essential requirement on efficient spectrum use.
- ISO/IEC 9646-1 - the conformance testing framework used for the test suite, test group and test case structure.
- ETSI EN 300 175-1 to EN 300 175-8 - the DECT Common Interface parts that define the physical layer, MAC, DLC, network, identities, security and speech/audio coding used throughout the tests.
- ETSI EN 300 700 - the WRS standard referenced for relay behavior and frame multiplexing.
- ETSI EN 301 406 - the harmonized DECT standard for operation in the 1 880 MHz to 1 900 MHz band mentioned in the scope notes.
- ITU-T Recommendation V.11 - the electrical characteristics for synchronization ports.
- ITU-T Recommendation O.153 - the basis for error-performance measurement.
- CENELEC EN 55022 - the radio disturbance measurement and limit methods referenced for EMC-related measurements.
What does the SIST EN 301 908-10 V4.1.1:2009 document contain?
This standard contains detailed test-oriented material rather than a product description. It gives the carrier-frequency formula and carrier numbering, slot and multiframe definitions, burst power-time templates, receiver test conditions, and the measurement logic for BER and FER.
It also includes test setups for conducted and radiated measurements, calibration of the test fixture, use of the Lower Tester (LT) and Upper Tester (UT), and arrangements for intermodulation measurements. Figures support the timing and relay functions, including the physical packet template, frame structures, synchronization behavior, and WRS/REP multiplexing cases.
Annex C provides the Test Standby Mode and related messages used for stand-alone testing of WRS and HyP equipment. Annex A links the test cases to the R&TTE essential requirements, and annex F is used for carrier notation and band-edge related testing.
Buy Documents
ETSI EN 301 908-10 V4.1.0 (2009-03) - Electromagnetic compatibility and Radio spectrum Matters (ERM); Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation cellular networks; Part 10: Harmonized EN for IMT-2000, FDMA/TDMA (DECT) covering essential requirements of article 3.2 of the R&TTE Directive
ETSI EN 301 908-10 V4.1.1 (2009-07) - Electromagnetic compatibility and Radio spectrum Matters (ERM); Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation cellular networks; Part 10: Harmonized EN for IMT-2000, FDMA/TDMA (DECT) covering essential requirements of article 3.2 of the R&TTE Directive
Get Certified
Connect with accredited certification bodies for this standard
ANCE
Mexican certification and testing association.
Intertek Slovenia
Intertek testing, inspection, and certification services in Slovenia.
LNE (Laboratoire National de Métrologie et d'Essais)
French national laboratory for metrology and testing.
Sponsored listings
Frequently Asked Questions
SIST EN 301 908-10 V4.1.1:2009 is a standard published by the Slovenian Institute for Standardization (SIST). Its full title is "Electromagnetic compatibility and Radio spectrum Matters (ERM) - Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation cellular networks - Part 10: Harmonized EN for IMT-2000, FDMA/TDMA (DECT) covering essential requirements of article 3.2 of the R&TTE Directive". This standard covers: The present document applies to terminal equipment for IMT-FT. IMT-FT is the Digital Enhanced Cordless Telecommunications (DECT) system being a member of the ITU IMT-2000 family. DECT terminal equipment consists of the following elements: a) Fixed Part (FP); b) Portable Part (PP); c) Cordless Terminal Adapter (CTA); d) Wireless Relay Station (WRS) (FP and PP combined with repeater functionality); e) Hybrid Part (HyP) (a PP with capability to act as a FP to provide PP to PP communication). These radio equipment types are capable of operating in all or any part of the frequency bands given in table 1. The IMT-FT (DECT) service frequency bands for transmitting and receiving for all elements are the parts of the European UMTS spectrum applicable for TDD operation, 1 900 MHz to 1 980 MHz and 2 010 MHz to 2 025 MHz, (see ERC/DEC(99)25 [18] and ERC/DEC(00)01 [19]). NOTE 1: IMT-FT equipment may have a second mode for providing operation also in the DECT band 1 880 MHz to 1 900 MHz. Application of DECT in the band 1 880 MHz to 1 900 MHz is covered by EN 301 406 [i.7]. Details of the DECT Common Interface may be found in EN 300 175 parts 1 to 8 [5] to [12]. Further details of the DECT system may be found in the ETSI Technical Reports, TR 101 178 [i.1] and ETR 043 [i.2]. The present document is intended to cover the provisions of Directive 1999/5/EC (R&TTE Directive) [1] article 3.2, which states that "[…] radio equipment shall be so constructed that it effectively uses the spectrum allocated to terrestrial/space radio communications and orbital resources so as to avoid harmful interference". In addition to the present document, other ENs that specify technical requirements in respect of essential requirements under other parts of article 3 of the R&TTE Directive [1] will apply to equipment within the scope of the present document.
The present document applies to terminal equipment for IMT-FT. IMT-FT is the Digital Enhanced Cordless Telecommunications (DECT) system being a member of the ITU IMT-2000 family. DECT terminal equipment consists of the following elements: a) Fixed Part (FP); b) Portable Part (PP); c) Cordless Terminal Adapter (CTA); d) Wireless Relay Station (WRS) (FP and PP combined with repeater functionality); e) Hybrid Part (HyP) (a PP with capability to act as a FP to provide PP to PP communication). These radio equipment types are capable of operating in all or any part of the frequency bands given in table 1. The IMT-FT (DECT) service frequency bands for transmitting and receiving for all elements are the parts of the European UMTS spectrum applicable for TDD operation, 1 900 MHz to 1 980 MHz and 2 010 MHz to 2 025 MHz, (see ERC/DEC(99)25 [18] and ERC/DEC(00)01 [19]). NOTE 1: IMT-FT equipment may have a second mode for providing operation also in the DECT band 1 880 MHz to 1 900 MHz. Application of DECT in the band 1 880 MHz to 1 900 MHz is covered by EN 301 406 [i.7]. Details of the DECT Common Interface may be found in EN 300 175 parts 1 to 8 [5] to [12]. Further details of the DECT system may be found in the ETSI Technical Reports, TR 101 178 [i.1] and ETR 043 [i.2]. The present document is intended to cover the provisions of Directive 1999/5/EC (R&TTE Directive) [1] article 3.2, which states that "[…] radio equipment shall be so constructed that it effectively uses the spectrum allocated to terrestrial/space radio communications and orbital resources so as to avoid harmful interference". In addition to the present document, other ENs that specify technical requirements in respect of essential requirements under other parts of article 3 of the R&TTE Directive [1] will apply to equipment within the scope of the present document.
SIST EN 301 908-10 V4.1.1:2009 is classified under the following ICS (International Classification for Standards) categories: 33.060.99 - Other equipment for radiocommunications; 33.100.01 - Electromagnetic compatibility in general. The ICS classification helps identify the subject area and facilitates finding related standards.
SIST EN 301 908-10 V4.1.1:2009 is associated with the following European legislation: EU Directives/Regulations: 1999/5/EC, TRRTP124; Standardization Mandates: M/284. When a standard is cited in the Official Journal of the European Union, products manufactured in conformity with it benefit from a presumption of conformity with the essential requirements of the corresponding EU directive or regulation.
SIST EN 301 908-10 V4.1.1:2009 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
Final draft ETSI EN 301 908-10 V4.1.0 (2009-03)
Harmonized European Standard (Telecommunications series)
Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Base Stations (BS), Repeaters and User Equipment (UE) for
IMT-2000 Third-Generation cellular networks;
Part 10: Harmonized EN for IMT-2000,
FDMA/TDMA (DECT)
covering essential requirements
of article 3.2 of the R&TTE Directive
2 Final draft ETSI EN 301 908-10 V4.1.0 (2009-03)
Reference
REN/DECT-000253
Keywords
3G, DECT, digital, generic, IMT-2000, radio,
regulation, testing
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2009.
All rights reserved.
TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
LTE™ is a Trade Mark of ETSI currently being registered
for the benefit of its Members and of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
3 Final draft ETSI EN 301 908-10 V4.1.0 (2009-03)
Contents
Intellectual Property Rights . 10
Foreword . 10
Introduction . 11
1 Scope . 12
2 References . 13
2.1 Normative references . 13
2.2 Informative references . 14
3 Definitions, symbols and abbreviations . 15
3.1 Definitions . 15
3.2 Symbols . 17
3.3 Abbreviations . 17
4 Technical requirements specifications . 18
4.1 Environmental profile . 18
4.2 Document layout . 18
4.2.1 Test suites . 19
4.2.2 Test groups. 19
4.2.3 Test cases . 20
4.3 Applicant's declaration . 20
4.4 Applicability of essential test suites . 20
4.4.1 Introduction. 20
4.4.2 Equipment that includes only a DECT RF receiver . 21
4.4.3 Equipment that includes a radio transmitter . 21
4.4.4 CTAs . 21
4.4.5 Equipment with a synchronization port . 21
4.4.6 Equipment incorporating the IPEI (PPs only) . 21
4.4.7 All FP equipment . 21
4.4.8 Equipment with combined FT and PT functionality . 21
4.4.8.1 Introduction . 21
4.4.8.2 Wireless Relay Station . 21
4.4.8.3 Direct PP to PP communication . 22
4.4.8.4 Distributed communications . 22
4.4.9 Provision of 4 Mbit/s services Equipment that is capable of using 4-level, 8-level, 16 level and/or
64-level modulation . 22
4.4.10 Dual mode handsets . 22
4.5 Conformance requirements . 22
4.5.1 General . 22
4.5.2 Accuracy and stability of RF carriers . 23
4.5.2.1 Definition of nominal position of RF carriers . 23
4.5.2.2 Limits . 23
4.5.2.3 Conformance . 23
4.5.3 Accuracy and stability of timing parameters . 23
4.5.3.1 Definitions . 23
4.5.3.1.1 Slot structure . 23
4.5.3.1.2 Definition of the position of p0 . 25
4.5.3.2 Limits . 25
4.5.3.2.1 Reference timer accuracy and stability . 25
4.5.3.2.2 RFP transmission jitter . 25
4.5.3.2.3 PP reference timer synchronization . 26
4.5.3.3 Conformance . 26
4.5.4 Transmission burst . 26
4.5.4.1 Definitions . 26
4.5.4.1.1 Introduction . 26
4.5.4.1.2 Physical packets. 27
ETSI
4 Final draft ETSI EN 301 908-10 V4.1.0 (2009-03)
4.5.4.1.3 Transmitted power . 27
4.5.4.1.4 Normal Transmitted Power (NTP) . 27
4.5.4.1.5 Transmitter attack time . 27
4.5.4.1.6 Transmitter release time . 27
4.5.4.1.7 Minimum power . 27
4.5.4.1.8 Maximum power . 27
4.5.4.1.9 Maintenance of transmission after packet end . 27
4.5.4.1.10 Transmitter idle power output . 27
4.5.4.2 Limits . 27
4.5.4.2.1 Transmitter attack time . 27
4.5.4.2.2 Transmitter release time . 27
4.5.4.2.3 Minimum power . 27
4.5.4.2.4 Maximum power . 28
4.5.4.2.5 Maintenance of transmission after packet end . 28
4.5.4.2.6 Transmitter idle power output . 28
4.5.4.3 Conformance . 28
4.5.5 Transmitted power . 28
4.5.5.1 Definitions . 28
4.5.5.1.1 PP and RFP with an integral antenna . 28
4.5.5.1.2 PP and RFP with external connections for all antennas . 28
4.5.5.1.3 PP and RFP with both integral and external antennas . 28
4.5.5.2 Limits . 28
4.5.5.3 Conformance . 28
4.5.6 RF carrier modulation . 29
4.5.6.1 Definition . 29
4.5.6.2 Limits . 29
4.5.6.3 Conformance . 29
4.5.7 Unwanted RF power radiation . 29
4.5.7.1 General . 29
4.5.7.2 Emissions due to modulation . 29
4.5.7.2.1 Definition. 29
4.5.7.2.2 Limits . 30
4.5.7.2.3 Conformance . 30
4.5.7.3 Emissions due to transmitter transients . 30
4.5.7.3.1 Definition. 30
4.5.7.3.2 Limits . 30
4.5.7.3.3 Conformance . 30
4.5.7.4 Emissions due to intermodulation . 31
4.5.7.4.1 Definition. 31
4.5.7.4.2 Limits . 31
4.5.7.4.3 Conformance . 31
4.5.7.5 Spurious emissions when allocated a transmit channel . 31
4.5.7.5.1 Definition. 31
4.5.7.5.2 Limits . 31
4.5.7.5.3 Conformance . 31
4.5.8 Radio receiver testing . 31
4.5.8.1 Radio receiver sensitivity . 31
4.5.8.1.1 Definition. 31
4.5.8.1.2 Limits . 32
4.5.8.1.3 Conformance . 32
4.5.8.2 Radio receiver reference BER and FER . 32
4.5.8.2.1 Definition. 32
4.5.8.2.2 Limits . 32
4.5.8.2.3 Conformance . 32
4.5.8.3 Radio receiver interference performance . 32
4.5.8.3.1 Definition. 32
4.5.8.3.2 Limits . 33
4.5.8.3.3 Conformance . 33
4.5.8.4 Radio receiver blocking case 1: owing to signals occurring at the same time but on other
frequencies . 33
4.5.8.4.1 Definition. 33
4.5.8.4.2 Limits . 33
ETSI
5 Final draft ETSI EN 301 908-10 V4.1.0 (2009-03)
4.5.8.4.3 Conformance . 34
4.5.8.5 Radio receiver blocking case 2: owing to signals occurring at a different time . 34
4.5.8.5.1 Definition. 34
4.5.8.5.2 Limits . 34
4.5.8.5.3 Conformance . 34
4.5.8.6 Receiver intermodulation performance . 34
4.5.8.6.1 Definition. 34
4.5.8.6.2 Limits . 34
4.5.8.6.3 Conformance . 34
4.5.8.7 Spurious emissions when the PP has no allocated transmit channel . 34
4.5.8.7.1 Definition. 34
4.5.8.7.2 Limits . 35
4.5.8.7.3 Conformance . 35
4.5.9 Intersystem synchronization (FP only) . 35
4.5.9.1 Description . 35
4.5.9.2 Wired synchronization ports . 35
4.5.9.2.1 FP as a master . 35
4.5.9.2.2 FP as a slave . 36
4.5.9.3 GPS synchronization . 36
4.5.9.3.1 FP with integrated Global Positioning System (GPS) synchronization . 36
4.5.9.3.2 External GPS synchronization device . 37
4.5.10 Equipment identity testing . 37
4.5.10.1 PP . 37
4.5.10.2 FP . 37
4.5.11 Efficient use of the radio spectrum . 38
4.5.11.1 Channel selection . 38
4.5.11.2 Channel confirmation . 38
4.5.11.2.1 For the PT . 38
4.5.11.2.2 For the FT . 38
4.5.11.3 Channel release . 38
4.5.11.4 General . 39
4.5.12 WRS testing . 39
4.5.12.1 General requirements . 39
4.5.12.2 Testing as a PP . 39
4.5.12.3 Testing as an RFP . 39
4.5.12.4 Additional requirements . 40
4.5.12.5 Conformance . 43
4.5.13 Requirements for PPs with direct PP to PP communication mode . 44
4.5.13.1 General requirements . 44
4.5.13.2 Setting the EUT in direct communications mode . 44
4.5.13.3 When the EUT has not initiated a call . 44
4.5.13.4 When the EUT initiates a call . 44
4.5.13.5 Conformance . 45
4.5.14 Distributed communications . 45
4.5.14.1 General requirements . 45
4.5.14.2 Testing as a PP . 45
4.5.14.3 Testing as an RFP . 45
4.5.14.4 Conformance . 46
4.5.15 Higher level modulation options . 46
4.5.15.1 Requirements . 46
4.5.15.2 Conformance . 46
5 Testing for compliance with technical requirements . 47
5.1 General test requirements . 47
5.1.1 Test philosophy . 47
5.1.2 Standard position . 48
5.1.3 Test antenna of the LT . 48
5.1.4 Substitution antenna . 48
5.1.5 Test fixture . 49
5.1.5.1 Description . 49
5.1.5.2 Calibration of the test fixture for the measurement of transmitter characteristics . 49
5.1.5.3 Calibration of the test fixture for the measurement of receiver characteristics . 50
ETSI
6 Final draft ETSI EN 301 908-10 V4.1.0 (2009-03)
5.1.5.4 Mode of use . 50
5.1.6 Equipment with a temporary or internal permanent antenna connector. 50
5.1.6.1 General . 50
5.1.6.2 Equipment with a temporary antenna connector . 51
5.1.7 Lower Tester (LT) . 51
5.1.7.1 Description . 51
5.1.7.2 Connections between the EUT and the LT . 51
5.1.7.3 Functions and abilities. 52
5.1.7.4 Signal generation uncertainty . 52
5.1.7.5 Modulated DECT-like carrier . 52
5.1.7.6 CW interferers . 52
5.1.7.7 DECT RF signal . 52
5.1.7.8 Test modulation signals . 53
5.1.8 Upper Tester (UT) . 53
5.1.8.1 Description of the UT. 53
5.1.8.2 The test standby mode . 53
5.1.8.3 Test messages . 53
5.1.8.4 Dummy setting when EUT is a RFP and it is in Test Standby Mode (TSM) . 54
5.1.9 Description of the Lower Tester FT and PT . 54
5.1.10 General test methods . 54
5.1.10.1 General . 54
5.1.10.2 Sampling the RF signal . 54
5.1.10.2.1 Introduction . 54
5.1.10.2.2 Sampling method . 54
5.1.10.3 Determining the reference position . 55
5.1.10.3.1 Case 1: EUTs that cannot transmit . 55
5.1.10.3.2 Case 2: EUTs that can transmit . 55
5.1.10.4 Bit error rate (BER) and Frame Error Ratio (FER) measurements . 55
5.1.11 Test setup . 55
5.1.11.1 General . 55
5.1.11.2 Test setup 1 . 55
5.1.11.3 Test setup 2 . 56
5.1.11.4 Test setup 3 . 56
5.1.11.5 Test setup 4 . 57
5.1.11.6 Test setup 5 . 57
5.1.12 Test arrangements for intermodulation measurements . 58
5.1.12.1 PT to PT arrangement . 58
5.1.12.2 FT to FT arrangement . 58
5.1.12.3 FT to PT arrangement . 59
5.1.13 Test conditions, power supply and ambient temperatures . 59
5.1.13.1 General . 59
5.1.13.2 Nominal test conditions . 60
5.1.13.3 Extreme test conditions . 60
5.1.13.4 Test power source - general requirements . 61
5.1.13.5 Nominal test power source . 61
5.1.13.5.1 Mains voltage . 61
5.1.13.5.2 Regulated lead acid battery power sources . 61
5.1.13.5.3 Nickel cadmium battery. 61
5.1.13.5.4 Other power sources . 62
5.1.13.6 Extreme test power source . 62
5.1.13.6.1 Mains voltage . 62
5.1.13.6.2 Regulated lead acid battery power sources . 62
5.1.13.6.3 Nickel cadmium battery. 62
5.1.13.6.4 Other power sources . 62
5.1.13.7 Testing of host connected equipment and plug-in cards . 62
5.1.13.7.1 Permitted approaches . 62
5.1.13.7.2 Alternative A: composite equipment . 62
5.1.13.7.3 Alternative B: use of a test jig and three hosts . 63
5.2 Interpretation of the measurement results . 63
5.3 Essential radio test suites . 64
5.3.1 General . 64
5.3.2 Accuracy and stability of RF carriers . 64
ETSI
7 Final draft ETSI EN 301 908-10 V4.1.0 (2009-03)
5.3.2.1 Test environment . 64
5.3.2.2 Method of measurement . 64
5.3.2.3 Verdict criteria when the EUT is a RFP . 65
5.3.2.4 Verdict criteria when the EUT is a PP . 65
5.3.3 Accuracy and stability of timing parameters . 65
5.3.3.1 Measurement of packet timing jitter . 65
5.3.3.1.1 Test environment . 65
5.3.3.1.2 Method of measurement . 66
5.3.3.1.3 Verdict criteria . 66
5.3.3.2 Measurement of the reference timing accuracy of a RFP . 66
5.3.3.2.1 Test environment . 66
5.3.3.2.2 Method of measurement . 66
5.3.3.2.3 Verdict criteria . 67
5.3.3.3 Measurement of packet transmission accuracy of a PP . 67
5.3.3.3.1 Test environment . 67
5.3.3.3.2 Method of measurement . 67
5.3.3.3.3 Verdict criteria . 68
5.3.4 Transmission burst . 68
5.3.4.1 Test environment . 68
5.3.4.2 Method of measurement . 68
5.3.4.3 Verdict criteria . 69
5.3.5 Transmitted power . 69
5.3.5.1 PP and RFP with an integral antenna . 69
5.3.5.1.1 Test environment . 69
5.3.5.1.2 Method of measurement . 69
5.3.5.1.3 Verdict criteria for all EUTs . 70
5.3.5.2 PP and RFP with external antenna connection(s). 70
5.3.5.2.1 Test environment . 70
5.3.5.2.2 Method of measurement . 71
5.3.5.2.3 Verdict criteria for all EUTs .
...
Harmonized European Standard (Telecommunications series)
Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Base Stations (BS), Repeaters and User Equipment (UE) for
IMT-2000 Third-Generation cellular networks;
Part 10: Harmonized EN for IMT-2000,
FDMA/TDMA (DECT)
covering essential requirements
of article 3.2 of the R&TTE Directive
2 ETSI EN 301 908-10 V4.1.1 (2009-07)
Reference
REN/DECT-000253
Keywords
3G, DECT, digital, generic, IMT-2000, radio,
regulation, testing
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2009.
All rights reserved.
TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
LTE™ is a Trade Mark of ETSI currently being registered
for the benefit of its Members and of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
3 ETSI EN 301 908-10 V4.1.1 (2009-07)
Contents
Intellectual Property Rights . 10
Foreword . 10
Introduction . 11
1 Scope . 12
2 References . 13
2.1 Normative references . 13
2.2 Informative references . 14
3 Definitions, symbols and abbreviations . 15
3.1 Definitions . 15
3.2 Symbols . 17
3.3 Abbreviations . 17
4 Technical requirements specifications . 18
4.1 Environmental profile . 18
4.2 Document layout . 18
4.2.1 Test suites . 19
4.2.2 Test groups. 19
4.2.3 Test cases . 20
4.3 Applicant's declaration . 20
4.4 Applicability of essential test suites . 20
4.4.1 Introduction. 20
4.4.2 Equipment that includes only a DECT RF receiver . 21
4.4.3 Equipment that includes a radio transmitter . 21
4.4.4 CTAs . 21
4.4.5 Equipment with a synchronization port . 21
4.4.6 Equipment incorporating the IPEI (PPs only) . 21
4.4.7 All FP equipment . 21
4.4.8 Equipment with combined FT and PT functionality . 21
4.4.8.1 Introduction . 21
4.4.8.2 Wireless Relay Station . 21
4.4.8.3 Direct PP to PP communication . 22
4.4.8.4 Distributed communications . 22
4.4.9 Provision of 4 Mbit/s services Equipment that is capable of using 4-level, 8-level, 16 level and/or
64-level modulation . 22
4.4.10 Dual mode handsets . 22
4.5 Conformance requirements . 22
4.5.1 General . 22
4.5.2 Accuracy and stability of RF carriers . 23
4.5.2.1 Definition of nominal position of RF carriers . 23
4.5.2.2 Limits . 23
4.5.2.3 Conformance . 23
4.5.3 Accuracy and stability of timing parameters . 23
4.5.3.1 Definitions . 23
4.5.3.1.1 Slot structure . 23
4.5.3.1.2 Definition of the position of p0 . 25
4.5.3.2 Limits . 25
4.5.3.2.1 Reference timer accuracy and stability . 25
4.5.3.2.2 RFP transmission jitter . 25
4.5.3.2.3 PP reference timer synchronization . 26
4.5.3.3 Conformance . 26
4.5.4 Transmission burst . 26
4.5.4.1 Definitions . 26
4.5.4.1.1 Introduction . 26
4.5.4.1.2 Physical packets. 27
ETSI
4 ETSI EN 301 908-10 V4.1.1 (2009-07)
4.5.4.1.3 Transmitted power . 27
4.5.4.1.4 Normal Transmitted Power (NTP) . 27
4.5.4.1.5 Transmitter attack time . 27
4.5.4.1.6 Transmitter release time . 27
4.5.4.1.7 Minimum power . 27
4.5.4.1.8 Maximum power . 27
4.5.4.1.9 Maintenance of transmission after packet end . 27
4.5.4.1.10 Transmitter idle power output . 27
4.5.4.2 Limits . 27
4.5.4.2.1 Transmitter attack time . 27
4.5.4.2.2 Transmitter release time . 27
4.5.4.2.3 Minimum power . 27
4.5.4.2.4 Maximum power . 28
4.5.4.2.5 Maintenance of transmission after packet end . 28
4.5.4.2.6 Transmitter idle power output . 28
4.5.4.3 Conformance . 28
4.5.5 Transmitted power . 28
4.5.5.1 Definitions . 28
4.5.5.1.1 PP and RFP with an integral antenna . 28
4.5.5.1.2 PP and RFP with external connections for all antennas . 28
4.5.5.1.3 PP and RFP with both integral and external antennas . 28
4.5.5.2 Limits . 28
4.5.5.3 Conformance . 28
4.5.6 RF carrier modulation . 29
4.5.6.1 Definition . 29
4.5.6.2 Limits . 29
4.5.6.3 Conformance . 29
4.5.7 Unwanted RF power radiation . 29
4.5.7.1 General . 29
4.5.7.2 Emissions due to modulation . 29
4.5.7.2.1 Definition. 29
4.5.7.2.2 Limits . 30
4.5.7.2.3 Conformance . 30
4.5.7.3 Emissions due to transmitter transients . 30
4.5.7.3.1 Definition. 30
4.5.7.3.2 Limits . 30
4.5.7.3.3 Conformance . 30
4.5.7.4 Emissions due to intermodulation . 31
4.5.7.4.1 Definition. 31
4.5.7.4.2 Limits . 31
4.5.7.4.3 Conformance . 31
4.5.7.5 Spurious emissions when allocated a transmit channel . 31
4.5.7.5.1 Definition. 31
4.5.7.5.2 Limits . 31
4.5.7.5.3 Conformance . 31
4.5.8 Radio receiver testing . 31
4.5.8.1 Radio receiver sensitivity . 31
4.5.8.1.1 Definition. 31
4.5.8.1.2 Limits . 32
4.5.8.1.3 Conformance . 32
4.5.8.2 Radio receiver reference BER and FER . 32
4.5.8.2.1 Definition. 32
4.5.8.2.2 Limits . 32
4.5.8.2.3 Conformance . 32
4.5.8.3 Radio receiver interference performance . 32
4.5.8.3.1 Definition. 32
4.5.8.3.2 Limits . 33
4.5.8.3.3 Conformance . 33
4.5.8.4 Radio receiver blocking case 1: owing to signals occurring at the same time but on other
frequencies . 33
4.5.8.4.1 Definition. 33
4.5.8.4.2 Limits . 33
ETSI
5 ETSI EN 301 908-10 V4.1.1 (2009-07)
4.5.8.4.3 Conformance . 34
4.5.8.5 Radio receiver blocking case 2: owing to signals occurring at a different time . 34
4.5.8.5.1 Definition. 34
4.5.8.5.2 Limits . 34
4.5.8.5.3 Conformance . 34
4.5.8.6 Receiver intermodulation performance . 34
4.5.8.6.1 Definition. 34
4.5.8.6.2 Limits . 34
4.5.8.6.3 Conformance . 34
4.5.8.7 Spurious emissions when the PP has no allocated transmit channel . 34
4.5.8.7.1 Definition. 34
4.5.8.7.2 Limits . 35
4.5.8.7.3 Conformance . 35
4.5.9 Intersystem synchronization (FP only) . 35
4.5.9.1 Description . 35
4.5.9.2 Wired synchronization ports . 35
4.5.9.2.1 FP as a master . 35
4.5.9.2.2 FP as a slave . 36
4.5.9.3 GPS synchronization . 36
4.5.9.3.1 FP with integrated Global Positioning System (GPS) synchronization . 36
4.5.9.3.2 External GPS synchronization device . 37
4.5.10 Equipment identity testing . 37
4.5.10.1 PP . 37
4.5.10.2 FP . 37
4.5.11 Efficient use of the radio spectrum . 38
4.5.11.1 Channel selection . 38
4.5.11.2 Channel confirmation . 38
4.5.11.2.1 For the PT . 38
4.5.11.2.2 For the FT . 38
4.5.11.3 Channel release . 38
4.5.11.4 General . 39
4.5.12 WRS testing . 39
4.5.12.1 General requirements . 39
4.5.12.2 Testing as a PP . 39
4.5.12.3 Testing as an RFP . 39
4.5.12.4 Additional requirements . 40
4.5.12.5 Conformance . 44
4.5.13 Requirements for PPs with direct PP to PP communication mode . 44
4.5.13.1 General requirements . 44
4.5.13.2 Setting the EUT in direct communications mode . 44
4.5.13.3 When the EUT has not initiated a call . 44
4.5.13.4 When the EUT initiates a call . 44
4.5.13.5 Conformance . 45
4.5.14 Distributed communications . 45
4.5.14.1 General requirements . 45
4.5.14.2 Testing as a PP . 45
4.5.14.3 Testing as an RFP . 45
4.5.14.4 Conformance . 46
4.5.15 Higher level modulation options . 46
4.5.15.1 Requirements . 46
4.5.15.2 Conformance . 46
5 Testing for compliance with technical requirements . 47
5.1 General test requirements . 47
5.1.1 Test philosophy . 47
5.1.2 Standard position . 48
5.1.3 Test antenna of the LT . 48
5.1.4 Substitution antenna . 48
5.1.5 Test fixture . 49
5.1.5.1 Description . 49
5.1.5.2 Calibration of the test fixture for the measurement of transmitter characteristics . 49
5.1.5.3 Calibration of the test fixture for the measurement of receiver characteristics . 50
ETSI
6 ETSI EN 301 908-10 V4.1.1 (2009-07)
5.1.5.4 Mode of use . 50
5.1.6 Equipment with a temporary or internal permanent antenna connector. 50
5.1.6.1 General . 50
5.1.6.2 Equipment with a temporary antenna connector . 51
5.1.7 Lower Tester (LT) . 51
5.1.7.1 Description . 51
5.1.7.2 Connections between the EUT and the LT . 51
5.1.7.3 Functions and abilities. 52
5.1.7.4 Signal generation uncertainty . 52
5.1.7.5 Modulated DECT-like carrier . 52
5.1.7.6 CW interferers . 52
5.1.7.7 DECT RF signal . 52
5.1.7.8 Test modulation signals . 53
5.1.8 Upper Tester (UT) . 53
5.1.8.1 Description of the UT. 53
5.1.8.2 The test standby mode . 53
5.1.8.3 Test messages . 53
5.1.8.4 Dummy setting when EUT is a RFP and it is in Test Standby Mode (TSM) . 54
5.1.9 Description of the Lower Tester FT and PT . 54
5.1.10 General test methods . 54
5.1.10.1 General . 54
5.1.10.2 Sampling the RF signal . 54
5.1.10.2.1 Introduction . 54
5.1.10.2.2 Sampling method . 54
5.1.10.3 Determining the reference position . 55
5.1.10.3.1 Case 1: EUTs that cannot transmit . 55
5.1.10.3.2 Case 2: EUTs that can transmit . 55
5.1.10.4 Bit error rate (BER) and Frame Error Ratio (FER) measurements . 55
5.1.11 Test setup . 55
5.1.11.1 General . 55
5.1.11.2 Test setup 1 . 55
5.1.11.3 Test setup 2 . 56
5.1.11.4 Test setup 3 . 56
5.1.11.5 Test setup 4 . 57
5.1.11.6 Test setup 5 . 57
5.1.12 Test arrangements for intermodulation measurements . 58
5.1.12.1 PT to PT arrangement . 58
5.1.12.2 FT to FT arrangement . 58
5.1.12.3 FT to PT arrangement . 59
5.1.13 Test conditions, power supply and ambient temperatures . 59
5.1.13.1 General . 59
5.1.13.2 Nominal test conditions . 60
5.1.13.3 Extreme test conditions . 60
5.1.13.4 Test power source - general requirements . 61
5.1.13.5 Nominal test power source . 61
5.1.13.5.1 Mains voltage . 61
5.1.13.5.2 Regulated lead acid battery power sources . 61
5.1.13.5.3 Nickel cadmium battery. 61
5.1.13.5.4 Other power sources . 62
5.1.13.6 Extreme test power source . 62
5.1.13.6.1 Mains voltage . 62
5.1.13.6.2 Regulated lead acid battery power sources . 62
5.1.13.6.3 Nickel cadmium battery. 62
5.1.13.6.4 Other power sources . 62
5.1.13.7 Testing of host connected equipment and plug-in cards . 62
5.1.13.7.1 Permitted approaches . 62
5.1.13.7.2 Alternative A: composite equipment . 62
5.1.13.7.3 Alternative B: use of a test jig and three hosts . 63
5.2 Interpretation of the measurement results . 63
5.3 Essential radio test suites . 64
5.3.1 General . 64
5.3.2 Accuracy and stability of RF carriers . 64
ETSI
7 ETSI EN 301 908-10 V4.1.1 (2009-07)
5.3.2.1 Test environment . 64
5.3.2.2 Method of measurement . 64
5.3.2.3 Verdict criteria when the EUT is a RFP . 65
5.3.2.4 Verdict criteria when the EUT is a PP . 65
5.3.3 Accuracy and stability of timing parameters . 65
5.3.3.1 Measurement of packet timing jitter . 65
5.3.3.1.1 Test environment . 65
5.3.3.1.2 Method of measurement . 66
5.3.3.1.3 Verdict criteria . 66
5.3.3.2 Measurement of the reference timing accuracy of a RFP . 66
5.3.3.2.1 Test environment . 66
5.3.3.2.2 Method of measurement . 66
5.3.3.2.3 Verdict criteria . 67
5.3.3.3 Measurement of packet transmission accuracy of a PP . 67
5.3.3.3.1 Test environment . 67
5.3.3.3.2 Method of measurement . 67
5.3.3.3.3 Verdict criteria . 68
5.3.4 Transmission burst . 68
5.3.4.1 Test environment . 68
5.3.4.2 Method of measurement . 68
5.3.4.3 Verdict criteria . 69
5.3.5 Transmitted power . 69
5.3.5.1 PP and RFP with an integral antenna . 69
5.3.5.1.1 Test environment . 69
5.3.5.1.2 Method of measurement . 69
5.3.5.1.3 Verdict criteria for all EUTs . 70
5.3.5.2 PP and RFP with external antenna connection(s). 70
5.3.5.2.1 Test environment . 70
5.3.5.2.2 Method of measurement . 71
5.3.5.2.3 Verdict criteria for all EUTs . 71
5.3.6 RF carrier modulation .
...
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.577(Electromagnetic compatibility and Radio spectrum Matters (ERM) - Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation cellular networks - Part 10: Harmonized EN for IMT-2000, FDMA/TDMA (DECT) covering essential requirements of article 3.2 of the R&TTE Directive33.100.01Elektromagnetna združljivost na splošnoElectromagnetic compatibility in general33.060.99Druga oprema za radijske komunikacijeOther equipment for radiocommunicationsICS:Ta slovenski standard je istoveten z:EN 301 908-10 Version 4.1.1SIST EN 301 908-10 V4.1.1:2009en01-september-2009SIST EN 301 908-10 V4.1.1:2009SLOVENSKI
STANDARD
ETSI ETSI EN 301 908-10 V4.1.1 (2009-07)2
Reference REN/DECT-000253 Keywords 3G, DECT, digital, generic, IMT-2000, radio, regulation, testing ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice Individual copies of the present document can be downloaded from: http://www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http://portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http://portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2009. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM, TIPHONTM, the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. LTE™ is a Trade Mark of ETSI currently being registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 301 908-10 V4.1.1:2009
ETSI ETSI EN 301 908-10 V4.1.1 (2009-07)3 Contents Intellectual Property Rights . 10 Foreword . 10 Introduction . 11 1 Scope . 12 2 References . 13 2.1 Normative references . 13 2.2 Informative references . 14 3 Definitions, symbols and abbreviations . 15 3.1 Definitions . 15 3.2 Symbols . 17 3.3 Abbreviations . 17 4 Technical requirements specifications . 18 4.1 Environmental profile . 18 4.2 Document layout . 18 4.2.1 Test suites . 19 4.2.2 Test groups. 19 4.2.3 Test cases . 20 4.3 Applicant's declaration . 20 4.4 Applicability of essential test suites . 20 4.4.1 Introduction. 20 4.4.2 Equipment that includes only a DECT RF receiver . 21 4.4.3 Equipment that includes a radio transmitter . 21 4.4.4 CTAs . 21 4.4.5 Equipment with a synchronization port . 21 4.4.6 Equipment incorporating the IPEI (PPs only) . 21 4.4.7 All FP equipment . 21 4.4.8 Equipment with combined FT and PT functionality . 21 4.4.8.1 Introduction . 21 4.4.8.2 Wireless Relay Station . 21 4.4.8.3 Direct PP to PP communication . 22 4.4.8.4 Distributed communications . 22 4.4.9 Provision of 4 Mbit/s services
Equipment that is capable of using 4-level, 8-level, 16 level and/or 64-level modulation . 22 4.4.10 Dual mode handsets . 22 4.5 Conformance requirements . 22 4.5.1 General . 22 4.5.2 Accuracy and stability of RF carriers . 23 4.5.2.1 Definition of nominal position of RF carriers . 23 4.5.2.2 Limits . 23 4.5.2.3 Conformance . 23 4.5.3 Accuracy and stability of timing parameters . 23 4.5.3.1 Definitions . 23 4.5.3.1.1 Slot structure . 23 4.5.3.1.2 Definition of the position of p0 . 25 4.5.3.2 Limits . 25 4.5.3.2.1 Reference timer accuracy and stability . 25 4.5.3.2.2 RFP transmission jitter . 25 4.5.3.2.3 PP reference timer synchronization . 26 4.5.3.3 Conformance . 26 4.5.4 Transmission burst . 26 4.5.4.1 Definitions . 26 4.5.4.1.1 Introduction . 26 4.5.4.1.2 Physical packets. 27 SIST EN 301 908-10 V4.1.1:2009
ETSI ETSI EN 301 908-10 V4.1.1 (2009-07)4 4.5.4.1.3 Transmitted power . 27 4.5.4.1.4 Normal Transmitted Power (NTP) . 27 4.5.4.1.5 Transmitter attack time . 27 4.5.4.1.6 Transmitter release time . 27 4.5.4.1.7 Minimum power . 27 4.5.4.1.8 Maximum power . 27 4.5.4.1.9 Maintenance of transmission after packet end . 27 4.5.4.1.10 Transmitter idle power output . 27 4.5.4.2 Limits . 27 4.5.4.2.1 Transmitter attack time . 27 4.5.4.2.2 Transmitter release time . 27 4.5.4.2.3 Minimum power . 27 4.5.4.2.4 Maximum power . 28 4.5.4.2.5 Maintenance of transmission after packet end . 28 4.5.4.2.6 Transmitter idle power output . 28 4.5.4.3 Conformance . 28 4.5.5 Transmitted power . 28 4.5.5.1 Definitions . 28 4.5.5.1.1 PP and RFP with an integral antenna . 28 4.5.5.1.2 PP and RFP with external connections for all antennas . 28 4.5.5.1.3 PP and RFP with both integral and external antennas . 28 4.5.5.2 Limits . 28 4.5.5.3 Conformance . 28 4.5.6 RF carrier modulation . 29 4.5.6.1 Definition . 29 4.5.6.2 Limits . 29 4.5.6.3 Conformance . 29 4.5.7 Unwanted RF power radiation . 29 4.5.7.1 General . 29 4.5.7.2 Emissions due to modulation . 29 4.5.7.2.1 Definition. 29 4.5.7.2.2 Limits . 30 4.5.7.2.3 Conformance . 30 4.5.7.3 Emissions due to transmitter transients . 30 4.5.7.3.1 Definition. 30 4.5.7.3.2 Limits . 30 4.5.7.3.3 Conformance . 30 4.5.7.4 Emissions due to intermodulation . 31 4.5.7.4.1 Definition. 31 4.5.7.4.2 Limits . 31 4.5.7.4.3 Conformance . 31 4.5.7.5 Spurious emissions when allocated a transmit channel . 31 4.5.7.5.1 Definition. 31 4.5.7.5.2 Limits . 31 4.5.7.5.3 Conformance . 31 4.5.8 Radio receiver testing . 31 4.5.8.1 Radio receiver sensitivity . 31 4.5.8.1.1 Definition. 31 4.5.8.1.2 Limits . 32 4.5.8.1.3 Conformance . 32 4.5.8.2 Radio receiver reference BER and FER . 32 4.5.8.2.1 Definition. 32 4.5.8.2.2 Limits . 32 4.5.8.2.3 Conformance . 32 4.5.8.3 Radio receiver interference performance . 32 4.5.8.3.1 Definition. 32 4.5.8.3.2 Limits . 33 4.5.8.3.3 Conformance . 33 4.5.8.4 Radio receiver blocking case 1: owing to signals occurring at the same time but on other frequencies . 33 4.5.8.4.1 Definition. 33 4.5.8.4.2 Limits . 33 SIST EN 301 908-10 V4.1.1:2009
ETSI ETSI EN 301 908-10 V4.1.1 (2009-07)5 4.5.8.4.3 Conformance . 34 4.5.8.5 Radio receiver blocking case 2: owing to signals occurring at a different time . 34 4.5.8.5.1 Definition. 34 4.5.8.5.2 Limits . 34 4.5.8.5.3 Conformance . 34 4.5.8.6 Receiver intermodulation performance . 34 4.5.8.6.1 Definition. 34 4.5.8.6.2 Limits . 34 4.5.8.6.3 Conformance . 34 4.5.8.7 Spurious emissions when the PP has no allocated transmit channel . 34 4.5.8.7.1 Definition. 34 4.5.8.7.2 Limits . 35 4.5.8.7.3 Conformance . 35 4.5.9 Intersystem synchronization (FP only) . 35 4.5.9.1 Description . 35 4.5.9.2 Wired synchronization ports . 35 4.5.9.2.1 FP as a master . 35 4.5.9.2.2 FP as a slave . 36 4.5.9.3 GPS synchronization . 36 4.5.9.3.1 FP with integrated Global Positioning System (GPS) synchronization . 36 4.5.9.3.2 External GPS synchronization device . 37 4.5.10 Equipment identity testing . 37 4.5.10.1 PP . 37 4.5.10.2 FP . 37 4.5.11 Efficient use of the radio spectrum . 38 4.5.11.1 Channel selection . 38 4.5.11.2 Channel confirmation . 38 4.5.11.2.1 For the PT . 38 4.5.11.2.2 For the FT . 38 4.5.11.3 Channel release . 38 4.5.11.4 General . 39 4.5.12 WRS testing . 39 4.5.12.1 General requirements . 39 4.5.12.2 Testing as a PP . 39 4.5.12.3 Testing as an RFP . 39 4.5.12.4 Additional requirements . 40 4.5.12.5 Conformance . 44 4.5.13 Requirements for PPs with direct PP to PP communication mode . 44 4.5.13.1 General requirements . 44 4.5.13.2 Setting the EUT in direct communications mode . 44 4.5.13.3 When the EUT has not initiated a call . 44 4.5.13.4 When the EUT initiates a call . 44 4.5.13.5 Conformance . 45 4.5.14 Distributed communications . 45 4.5.14.1 General requirements . 45 4.5.14.2 Testing as a PP . 45 4.5.14.3 Testing as an RFP . 45 4.5.14.4 Conformance . 46 4.5.15 Higher level modulation options . 46 4.5.15.1 Requirements . 46 4.5.15.2 Conformance . 46 5 Testing for compliance with technical requirements . 47 5.1 General test requirements . 47 5.1.1 Test philosophy . 47 5.1.2 Standard position . 48 5.1.3 Test antenna of the LT . 48 5.1.4 Substitution antenna . 48 5.1.5 Test fixture . 49 5.1.5.1 Description . 49 5.1.5.2 Calibration of the test fixture for the measurement of transmitter characteristics . 49 5.1.5.3 Calibration of the test fixture for the measurement of receiver characteristics . 50 SIST EN 301 908-10 V4.1.1:2009
ETSI ETSI EN 301 908-10 V4.1.1 (2009-07)6 5.1.5.4 Mode of use . 50 5.1.6 Equipment with a temporary or internal permanent antenna connector. 50 5.1.6.1 General . 50 5.1.6.2 Equipment with a temporary antenna connector . 51 5.1.7 Lower Tester (LT) . 51 5.1.7.1 Description . 51 5.1.7.2 Connections between the EUT and the LT . 51 5.1.7.3 Functions and abilities. 52 5.1.7.4 Signal generation uncertainty . 52 5.1.7.5 Modulated DECT-like carrier . 52 5.1.7.6 CW interferers . 52 5.1.7.7 DECT RF signal . 52 5.1.7.8 Test modulation signals . 53 5.1.8 Upper Tester (UT) . 53 5.1.8.1 Description of the UT. 53 5.1.8.2 The test standby mode . 53 5.1.8.3 Test messages . 53 5.1.8.4 Dummy setting when EUT is a RFP and it is in Test Standby Mode (TSM) . 54 5.1.9 Description of the Lower Tester FT and PT . 54 5.1.10 General test methods . 54 5.1.10.1 General . 54 5.1.10.2 Sampling the RF signal . 54 5.1.10.2.1 Introduction . 54 5.1.10.2.2 Sampling method . 54 5.1.10.3 Determining the reference position . 55 5.1.10.3.1 Case 1: EUTs that cannot transmit . 55 5.1.10.3.2 Case 2: EUTs that can transmit . 55 5.1.10.4 Bit error rate (BER) and Frame Error Ratio (FER) measurements . 55 5.1.11 Test setup . 55 5.1.11.1 General . 55 5.1.11.2 Test setup 1 . 55 5.1.11.3 Test setup 2 . 56 5.1.11.4 Test setup 3 . 56 5.1.11.5 Test setup 4 . 57 5.1.11.6 Test setup 5 . 57 5.1.12 Test arrangements for intermodulation measurements . 58 5.1.12.1 PT to PT arrangement . 58 5.1.12.2 FT to FT arrangement . 58 5.1.12.3 FT to PT arrangement . 59 5.1.13 Test conditions, power supply and ambient temperatures . 59 5.1.13.1 General . 59 5.1.13.2 Nominal test conditions . 60 5.1.13.3 Extreme test conditions . 60 5.1.13.4 Test power source - general requirements . 61 5.1.13.5 Nominal test power source . 61 5.1.13.5.1 Mains voltage . 61 5.1.13.5.2 Regulated lead acid battery power sources . 61 5.1.13.5.3 Nickel cadmium battery. 61 5.1.13.5.4 Other power sources . 62 5.1.13.6 Extreme test power source . 62 5.1.13.6.1 Mains voltage . 62 5.1.13.6.2 Regulated lead acid battery power sources . 62 5.1.13.6.3 Nickel cadmium battery. 62 5.1.13.6.4 Other power sources . 62 5.1.13.7 Testing of host connected equipment and plug-in cards . 62 5.1.13.7.1 Permitted approaches . 62 5.1.13.7.2 Alternative A: composite equipment . 62 5.1.13.7.3 Alternative B: use of a test jig and three hosts . 63 5.2 Interpretation of the measurement results . 63 5.3 Essential radio test suites . 64 5.3.1 General . 64 5.3.2 Accuracy and stability of RF carriers . 64 SIST EN 301 908-10 V4.1.1:2009
ETSI ETSI EN 301 908-10 V4.1.1 (2009-07)7 5.3.2.1 Test environment . 64 5.3.2.2 Method of measurement . 64 5.3.2.3 Verdict criteria when the EUT is a RFP . 65 5.3.2.4 Verdict criteria when the EUT is a PP . 65 5.3.3 Accuracy and stability of timing parameters . 65 5.3.3.1 Measurement of packet timing jitter . 65 5.3.3.1.1 Test environment . 65 5.3.3.1.2 Method of measurement . 66 5.3.3.1.3 Verdict criteria . 66 5.3.3.2 Measurement of the reference timing accuracy of a RFP . 66 5.3.3.2.1 Test environment . 66 5.3.3.2.2 Method of measurement . 66 5.3.3.2.3 Verdict criteria . 67 5.3.3.3 Measurement of packet transmission accuracy of a PP . 67 5.3.3.3.1 Test environment . 67 5.3.3.3.2 Method of measurement . 67 5.3.3.3.3 Verdict criteria . 68 5.3.4 Transmission burst . 68 5.3.4.1 Test environment . 68 5.3.4.2 Method of measurement . 68 5.3.4.3 Verdict criteria . 69 5.3.5 Transmitted power . 69 5.3.5.1 PP and RFP with an integral antenna . 69 5.3.5.1.1 Test environment . 69 5.3.5.1.2 Method of measurement . 69 5.3.5.1.3 Verdict criteria for all EUTs . 70 5.3.5.2 PP and RFP with external antenna connection(s). 70 5.3.5.2.1 Test environment . 70 5.3.5.2.2 Method of measurement .
...