SIST EN 61290-10-5:2015

SLOVENSKI STANDARD
01-april-2015
2SWLþQLRMDþHYDOQLNL3UHVNXVQHPHWRGHGHO9HþNDQDOQLSDUDPHWUL
5D]SUãHQRRMDþHQMH5DPDQRYHJDRMDþHYDOQLNDLQãXPQRãWHYLOR,(&

Optical amplifiers - Test methods -- Part 10-5: Multichannel parameters - Distributed
Raman amplifier gain and noise figure (IEC 61290-10-5:2014)
Prüfverfahren für Lichtwellenleiter-Verstärker - Teil 10-5: Mehrkanalparameter -
Verstärkung und Rauschzahl von verteilten Raman-Verstärkern (IEC 61290-10-5:2014)
Amplificateurs optiques - Méthodes d'essai - Partie 10-5: Paramètres à canaux multiples
- Gain et facteur de bruit des amplificateurs Raman répartis (CEI 61290-10-5:2014)
Ta slovenski standard je istoveten z: EN 61290-10-5:2014
ICS:
33.180.30 2SWLþQLRMDþHYDOQLNL Optic amplifiers
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN 61290-10-5

NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2014
ICS 33.180.30
English Version
Optical amplifiers - Test methods - Part 10-5: Multichannel
parameters - Distributed Raman amplifier gain and noise figure
(IEC 61290-10-5:2014)
Amplificateurs optiques - Méthodes d'essai - Partie 10-5: Prüfverfahren für Lichtwellenleiter-Verstärker - Teil 10-5:
Paramètres à canaux multiples - Gain et facteur de bruit Mehrkanalparameter - Verstärkung und Rauschzahl von
des amplificateurs Raman répartis verteilten Raman-Verstärkern
(CEI 61290-10-5:2014) (IEC 61290-10-5:2014)
This European Standard was approved by CENELEC on 2014-06-27. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 61290-10-5:2014 E
Foreword
The text of document 86C/1142/CDV, future edition 1 of IEC 61290-10-5, prepared by SC 86C "Fibre
optic systems and active devices” of IEC/TC 86 “Fibre optics" was submitted to the IEC-CENELEC
parallel vote and approved by CENELEC as EN 61290-10-5:2014.

The following dates are fixed:
(dop) 2015-03-27
• latest date by which the document has to be
implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2017-06-27
• latest date by which the national
standards conflicting with the
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
Endorsement notice
The text of the International Standard IEC 61290-10-5:2014 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:

IEC 61290-3 NOTE Harmonized as EN 61290-3.
IEC 61290-10-4 NOTE Harmonized as EN 61290-10-4.

- 3 - EN 61290-10-5:2014
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.

NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu
Publication Year Title EN/HD Year

IEC 60825-1 -  Safety of laser products -- Part 1: EN 60825-1 -
Equipment classification and requirements
IEC 61291-1 -  Optical amplifiers -- Part 1: Generic EN 61291-1 -
specification
IEC 61291-4 -  Optical amplifiers -- Part 4: Multichannel EN 61291-4 -
applications - Performance specification
template
IEC/TR 61292-4 -  Optical amplifiers -- Part 4: Maximum - -
permissible optical power for the damage-
free and safe use of optical amplifiers,
including Raman amplifiers
IEC 61290-10-5 ®
Edition 1.0 2014-05
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Optical amplifiers – Test methods –

Part 10-5: Multichannel parameters – Distributed Raman amplifier gain and

noise figure
Amplificateurs optiques – Méthodes d'essai –

Partie 10-5: Paramètres à canaux multiples – Gain et facteur de bruit des

amplificateurs Raman répartis
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX S
ICS 33.180.30 ISBN 978-2-8322-1581-4

– 2 – IEC 61290-10-5:2014 © IEC 2014
CONTENTS
FOREWORD . 3
1 Scope and object . 5
2 Normative references . 5
3 Terms, definitions and abbreviations . 6
3.1 Terms and definitions . 6
3.2 Abbreviated terms . 7
4 DRA gain and noise figure parameters – Overview . 7
5 Apparatus . 9
5.1 General . 9
5.2 Multi-channel signal source . 10
5.3 Polarization controller . 11
5.4 Optical spectrum analyser . 11
5.5 Optical power meter . 12
5.6 Tuneable narrowband source . 12
5.7 Broadband optical source . 12
5.8 Optical connectors and jumpers . 12
6 Test sample . 12
7 Procedure . 12
7.1 Overview. 12
7.1.1 Channel on-off gain . 12
7.1.2 Pump module channel insertion loss and channel net gain . 13
7.1.3 Channel equivalent noise figure (NF) . 13
7.2 Calibration . 13
7.2.1 Calibration of optical bandwidth . 13
7.2.2 Calibration of OSA power correction factor . 15
7.3 Measurement . 15
7.4 Calculation . 17
7.4.1 Channel on-off gain . 17
7.4.2 Channel net gain . 17
7.4.3 Channel equivalent NF. 17
8 Test results . 17
Annex A (informative) Field measurements versus laboratory measurements . 19
Annex B (informative) Pump depletion and channel-to-channel Raman scattering . 20
Bibliography . 21

Figure 1 – Distributed Raman amplification in co-propagating (left) and count-
propagating (right) configurations . 9
Figure 2 – Measurement set-up without a pump module. 10
Figure 3 – Measurement set-up for counter-propagating configuration . 10
Figure 4 – Measurement set-up for co-propagating configuration . 10
Figure 5 – Possible implementation of a multi-channel signal source . 11

IEC 61290-10-5:2014 © IEC 2014 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
OPTICAL AMPLIFIERS –
TEST METHODS –
Part 10-5: Multichannel parameters –
Distributed Raman amplifier gain and noise figure

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61290-10-5 has been prepared by 86C: Fibre optic systems and
active devices, of IEC technical committee 86: Fibre optics.
The text of this standard is based on the following documents:
CDV Report on voting
86C/1142/CDV 86C/1233/RVC
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.

– 4 – IEC 61290-10-5:2014 © IEC 2014
A list of all parts in the IEC 61290 series, published under the general title Optical amplifiers –
Test methods, can be found on the IEC website.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
IMPORTANT – The 'colour inside' logo on the cover page of this publication indicates
that it contains colours which are considered to be useful for the correct
understanding of its contents. Users should therefore print this document using a
colour printer.
IEC 61290-10-5:2014 © IEC 2014 – 5 –
OPTICAL AMPLIFIERS –
TEST METHODS –
Part 10-5: Multichannel parameters –
Distributed Raman amplifier gain and noise figure

1 Scope and object
This part of IEC 61290 applies to distributed Raman amplifiers (DRAs). DRAs are based on
the process whereby Raman pump power is introduced into the transmission fibre, leading to
signal amplification within the transmission fibre through stimulated Raman scattering.
A detailed overview of the technology and applications of DRAs can be found in
IEC TR 61292-6.
A fundamental difference between these amplifiers and discrete amplifiers, such as EDFAs, is
that the latter can be described using a black box approach with well-defined input and output
ports. On the other hand, a DRA is basically a pump module, with the actual amplification
process taking place along the transmission fibre. This difference means that standard
methods described in other parts of IEC 61290 for measuring amplifier parameters, such as
gain and noise figure, cannot be applied without modification.
The object of this standard is to establish uniform requirements for accurate and reliable
measurements, using an optical spectrum analyser (OSA), of the following DRA parameters:
a) channel on-off gain;
b) pump unit insertion loss;
c) channel net gain;
d) channel signal-spontaneous noise figure.
The measurement method is largely based on the interpolated source subtraction (ISS)
method using an optical spectrum analyser, as described and elaborated in IEC 61290-10-4,
with relevant modifications relating to a DRA.
All numerical values followed by (‡) are suggested values for which the measurement is
assured. Other values may be acceptable but should be verified.
NOTE General aspects of noise figure test methods are reported in IEC 61290-3.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and
are indispensable for its application. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any
amendments) applies.
IEC 60825-1, Safety of laser products – Part 1: Equipment classification and requirements
IEC 61291-1, Optical amplifiers – Part 1: Generic specification
IEC 61291-4, Optical amplifiers – Part 4: Multichannel applications – Performance
specification template
– 6 – IEC 61290-10-5:2014 © IEC 2014
IEC TR 61292-4, Optical amplifiers – Part 4: Maximum permissible optical power for the
damage-free and safe use of optical amplifiers, including Raman amplifiers
3 Terms, definitions and abbreviations
3.1 Terms and definitions
3.1.1
Raman pump power
optical power produced by the DRA to enable Raman amplification of signal channels
Note 1 to entry: The Raman pump power shall be at a lower wavelength than the signal channels.
3.1.2
fibre span
length of fibre into which signal channels and Raman pump power are introduced, and Raman
amplification of the signal channels takes place via stimulated Raman scattering
3.1.3
co-propagating configuration
forward pumping configuration
configuration whereby the Raman pump power is coupled to the input of the fibre span such
that the signal channels and Raman pump power propagate in the same (forward) direction
3.1.4
counter-propagating configuration
backward pumping configuration
configuration whereby the Raman pump power is coupled to the output of the fibre span such
that the signal channels and Raman pump power propagate in opposite directions
3.1.5
pump module
module that produces Raman pump power and couples it into the connected fibre span
Note 1 to entry: If the pump module is connected to the input of the fibre span, then both the incoming signal
channels and Raman pump power are coupled to the fibre span.
Note 2 to entry: If the pump module is connected to the output of the fibre span, then the pump power is coupled
into the fibre span, while the signal channels exiting the fibre span pass through the pump module from the input
port to the output port.
Note 3 to entry: In this standard, the convention will be used whereby the input port of the pump module is
defined as the port into which the signal channels enter, while the output port is defined as the port through which
the signal channels exit. Thus, in co-propagating configuration the Raman pump power exits the pump module from
the output port, while in counter-propagating configuration the Raman pump power exits the pump module from the
input port.
3.1.6
channel on-off gain
G
on-off
ratio of the channel power at the output of the fibre span when the pump module is
operational to the channel power at the same point when the pump module is not operational
3.1.7
pump module channel insertion loss
IL
ratio of the channel power at the input of the pump module to the channel power at the output
of the pump module
IEC 61290-10-5:2014 © IEC 2014 – 7 –
3.1.8
channel net gain
G
net
channel on-off gain minus the pump module channel insertion loss, in dB
3.1.9
channel equivalent noise figure
NF
sig-ASE,eq
channel noise figure due to signal-spontaneous beat noise (see IEC 61290-3) of an equivalent
discrete amplifier placed at the output of the fibre span which has the same channel gain as
the DRA channel on-off gain, and generates the same amount of ASE as that generated by
the DRA at the output of the fibre span.
3.2 Abbreviated terms
ASE amplified spontaneous emission
DRA distributed Raman amplifier
EDFA Erbium doped fibre amplifier
FWHM full-width half-maximum
GFF gain flattening filter
ISS interpolated source subtraction
NF noise figure
RBW resolution bandwidth
OSA optical spectrum analyser
OSNR optical signal-to-noise ratio
PCF power correction factor
SMF single-mode fibre
SSE source spontaneous emission
VOA variable optical attenuator
4 DRA gain and noise figure parameters – Overview
NOTE Unless specifically stated otherwise, all equation and definitions in this clause and onwards are given in
linear units, and not dB.
Figure 1 shows the application of DRAs in co-propagating (forward pumping) and counter-
propagating (backward pumping) configurations. As a general rule, counter propagating
configuration is much more widely used compared to co-propagating configuration.
As with any amplifier, one of the main parameters of interest is the channel gain (see
IEC 61291-1 and IEC 61291-4). However, unlike discrete amplifiers, where the channel gain
is simply defined as the ratio of the channel power at the output port to the channel power at
the input port, with a DRA, the situation is more complex. In principle, the DRA includes both
the pump module, which supplies the pump power, and the fibre span, where the actual
amplification takes place. Thus, one option for defining channel gain is to define it as the ratio
of the channel power at point C (Figure 1) to the channel power at point A, while the pumps
are operational. However, since this definition also include the fibre span loss, which is often
larger than the gain supplied by the Raman pumps, this definition is not very useful.
A much more useful quantity is the channel on-off gain, which is defined as the ratio of the
channel power at the output of the fibre span when the Raman pumps are on to the channel
power at the same point but when the pumps are off (see the graphs in Figure 1).

– 8 – IEC 61290-10-5:2014 © IEC 2014
P
on
G =
(1)
on−off
P
off
In practice, the channel on-off gain may be measured at any point following the fibre span, for
example point C for co-propagating configuration, or points B and C for the counter-
propagating configuration.
Another parameter of interest for DRAs is the pump module channel insertion loss, which is
defined as the ratio of the channel power at the input port of the pump module to the channel
power at the output port of the pump module (points A and B for co-propagating configuration,
and points B and C for counter propagating configuration).
P
pump unit input
IL=
(2)
P
pump unit output
Since no amplification takes place within the pump module, this is just passive insertion loss,
and is not affected by the status of the pumps (on or off).
The channel on-off gain and pump module channel insertion loss can be combined into a
single quantity, the channel net gain, which is defined in dB as
G (dB)=G (dB)−IL(dB) (3)
net on−off
The channel net gain is particularly useful for counter-propagating configuration, as it may be
directly measured in linear units as the ratio of the channel power at point C when the pumps
are on to the channel power at point B when the pumps are off. When the pump module
includes a gain flattening filter (GFF) to tailor the spectral shape of the Raman gain, then the
channel net gain includes the effect of the GFF, as opposed to the channel on-off gain which
does not (i.e. the channel on-off gain has a non-flat dependence on the channel wavelength).
For the co-propagating configuration, the channel net gain has less physical meaning, and it
is more common to separately define the channel on-off gain and pump module channel
insertion loss.
Another important parameter relevant to a DRA is the channel equivalent noise figure (NF)
due to signal-spontaneous beat noise. This quantity is only relevant to counter-propagating
configuration. The channel equivalent NF of a DRA is defined as the NF of an equivalent
discrete amplifier placed at the output of the fibre span, which provides the same amount of
channel gain as the DRA channel on-off gain, and generates the same amount of amplified
spontaneous emission (ASE) as that generated at the fibre span output by the DRA. The
channel equivalent noise figure (in dB) due to signal-spontaneous beat noise is given by (see
IEC 61290-3):
NF = 10log (ρ /(G hν))
(4)
sig−ASE,eq 10 ASE,B on−off
where
ρ is the ASE spectral density at the channel wavelength λ (in both polarization
ASE,B
modes) measured at the output of the fibre span (point B in the counter-propagating
configuration of Figure 1);
ν=c /λ is the channel frequency;
h is Planck’s constant.
Using the relation between the channel on-off gain and the channel net gain, it is easily
shown that the channel equivalent NF is also given by

IEC 61290-10-5:2014 © IEC 2014 – 9 –
NF = 10log (ρ /(G hν))
sig−ASE,eq 10 ASE,C net (5)
where
ρ is now measured at point C.
ASE,C
Counter-propagating configuration
Co-propagating configuration
Fibre span
Fibre span
Signal Signal
A C A C
B B
Pump Pump
module module
Pump Pump
30  30
Pump
Pump
Signal with pump on
Signal with pump on
20  20
Signal with pump off
Signal with pump off
10  10
0   0
–10
–10
–20
–20
On-off On-off
gain gain
–30 –30
0 50 100 150 0 50 100 150
Position along span  (km) Position along span  (km)
IEC  1389/14
NOTE The graphs show the evolution of pump and signal along the fibre span.
Figure 1 – Distributed Raman amplification in co-propagating (left)
and count-propagating (right) configurations
When measuring DRA gain and NF, the following issues should
...