SIST EN ISO 2401:2018

SLOVENSKI STANDARD
SIST EN ISO 2401:2018
01-november-2018
1DGRPHãþD
SIST EN 22401:1998
'RGDMQLPDWHULDOL]DYDUMHQMH2SODãþHQHHOHNWURGH8JRWDYOMDQMHL]NRULVWND
KLWURVWLRGWDOMHYDQMDLQWDOLOQHNRQVWDQWH,62
Welding consumables - Covered electrodes - Determination of the efficiency, metal
recovery and deposition coefficient (ISO 2401:2018)
Schweißzusätze - Umhüllte Stabelelektroden - Bestimmung der Ausbringung, der
Gesamtausbringung und des Abschmelzkoeffizienten (ISO 2401:2018)
Électrodes enrobées - Détermination de l'efficacité, du rendement du métal et du
coefficient de dépôt (ISO 2401:2018)
Ta slovenski standard je istoveten z: EN ISO 2401:2018
ICS:
25.160.20 Potrošni material pri varjenju Welding consumables
SIST EN ISO 2401:2018 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 2401:2018

---------------------- Page: 2 ----------------------

SIST EN ISO 2401:2018


EN ISO 2401
EUROPEAN STANDARD

NORME EUROPÉENNE

September 2018
EUROPÄISCHE NORM
ICS 25.160.20 Supersedes EN 22401:1994
English Version

Welding consumables - Covered electrodes -
Determination of the efficiency, metal recovery and
deposition coefficient (ISO 2401:2018)
Électrodes enrobées - Détermination de l'efficacité, du Schweißzusätze - Umhüllte Stabelelektroden -
rendement du métal et du coefficient de dépôt (ISO Bestimmung der Ausbringung, der Gesamtausbringung
2401:2018) und des Abschmelzkoeffizienten (ISO 2401:2018)
This European Standard was approved by CEN on 4 September 2018.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 2401:2018 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 2401:2018
EN ISO 2401:2018 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 2401:2018
EN ISO 2401:2018 (E)
European foreword
This document (EN ISO 2401:2018) has been prepared by Technical Committee ISO/TC 44 "Welding
and allied processes" in collaboration with Technical Committee CEN/TC 121 “Welding and allied
processes” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2019, and conflicting national standards shall
be withdrawn at the latest by March 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 22401:1994.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 2401:2018 has been approved by CEN as EN ISO 2401:2018 without any modification.


3

---------------------- Page: 5 ----------------------

SIST EN ISO 2401:2018

---------------------- Page: 6 ----------------------

SIST EN ISO 2401:2018
INTERNATIONAL ISO
STANDARD 2401
Second edition
2018-08
Welding consumables — Covered
electrodes — Determination of
the efficiency, metal recovery and
deposition coefficient
Électrodes enrobées — Détermination de l'efficacité, du rendement du
métal et du coefficient de dépôt
Reference number
ISO 2401:2018(E)
©
ISO 2018

---------------------- Page: 7 ----------------------

SIST EN ISO 2401:2018
ISO 2401:2018(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 2401:2018
ISO 2401:2018(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Test plates . 2
4.1 Number . 2
4.2 Specification . 2
5 Procedure. 3
6 Calculation of efficiency and metal recovery . 4
7 Rounding procedure . 5
8 Calculation of deposition coefficient . 5
© ISO 2018 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 2401:2018
ISO 2401:2018(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso
.org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 44, Welding and allied processes,
Subcommittee SC 3, Welding consumables.
Any feedbac
...