iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN ISO 19085-11:2024

(Main)

Woodworking machines - Safety - Part 11: Combined machines (ISO 19085-11:2024)

Woodworking machines - Safety - Part 11: Combined machines (ISO 19085-11:2024)

This document specifies the safety requirements and measures for combined woodworking machines (defined in 3.1), capable of continuous production use, with manual loading and unloading of the workpiece and hereinafter referred to also as “machines”.
The machines are designed to cut solid wood and material with similar physical characteristics to wood.
It deals with all significant hazards, hazardous situations and events, listed in Annex A, relevant to the machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer; reasonably foreseeable misuse has been considered too. Transport, assembly, dismantling, disabling and scrapping phases have also been taken into account.
This document does apply to machines also equipped with the devices/additional working units listed in the Scopes of ISO 19085 5:202x, ISO 19085 6:202x, ISO 19085-7:202x and ISO 19085-9:202x.
This document does not apply to:
a) machines incorporating only a planing unit and a mortising device;
NOTE    Such machines are dealt with in ISO 19085-7:202x.
b) combined machines incorporating a band saw unit;
c) machines with a mortising unit with a separate drive other than the planing unit drive;
d) machines intended for use in potentially explosive atmosphere;
e) machines manufactured before the date of its publication as an International Standard.

Holzbearbeitungsmaschinen - Sicherheit - Teil 11: Kombinierte Maschinen (ISO 19085-11:2024)

Machines à bois - Sécurité - Partie 11: Machines combinées (ISO 19085-11:2024)

Le présent document spécifie les exigences et les mesures de sécurité pour les machines à bois combinées (définies en 3.1), capables d’une utilisation en production continue, à chargement et déchargement manuels de la pièce et ci-après désignées également «machines».
Les machines sont conçues pour la coupe de bois massif et de matériaux ayant des caractéristiques physiques similaires à celles du bois (voir l’ISO 19085-1:2021, 3.2).
Le présent document traite de tous les phénomènes dangereux, situations dangereuses et événements dangereux significatifs, énumérés à l’Annexe A, applicables aux machines lorsqu'elles sont utilisées, réglées et entretenues comme prévu et dans les conditions prévues par le fabricant; une mauvaise utilisation raisonnablement prévisible a été prise en considération également. Les phases de transport, d'assemblage, de démontage, de mise hors service et de mise au rebut ont également été prises en compte.
Le présent document s’applique aux machines également équipées des dispositifs ou unités de travail supplémentaires énumérés dans les Domaines d'application de l'ISO 19085-5:2024, l'ISO 19085-6:2024, l'ISO 19085-7:2024 et l'ISO 19085-9:2024.
Le présent document ne s’applique pas:
a)       aux machines comportant uniquement une unité de dégauchissage et un dispositif de mortaisage;
NOTE            Les machines comportant uniquement une unité de dégauchissage et un dispositif de mortaisage sont traitées dans l’ISO 19085-7:2024.
b)       aux machines combinées comportant une scie à ruban;
c)        aux machines comportant une unité de mortaisage ayant un entraînement séparé autre que l’entraînement de l’unité de dégauchissage;
d)       aux machines prévues pour une utilisation en atmosphère explosible;
e)       aux machines fabriquées avant la publication du présent document.

Lesnoobdelovalni stroji - Varnost - 11. del: Kombinirani stroji (ISO 19085-11:2024)

General Information

Status
Not Published
Public Enquiry End Date
11-Sep-2022
ICS
13.110 - Safety of machinery
79.120.10 - Woodworking machines
Technical Committee
VSN - Safety of machinery
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
09-Oct-2024
Due Date
14-Dec-2024
Directive
2006/42/EC - Directive 2006/42/EC of the European Parliament and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast)
Mandate
M/396 - Mandate to CEN and Cenelec for standardisation in the field of machinery
Ref Project
EN ISO 19085-11:2024 - Woodworking machines - Safety - Part 11: Combined machines (ISO 19085-11:2024)

Relations

Revised
SIST EN ISO 19085-11:2020 - Woodworking machines - Safety - Part 11: Combined machines (ISO 19085-11:2020)
Effective Date
18-Jan-2023

Buy Standard

prEN ISO 19085-11:2022prEN ISO 19085-11:2022
PreviousNext
Draft
prEN ISO 19085-11:2022
English language
35 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
oSIST prEN ISO 19085-11:2022
01-september-2022
Lesnoobdelovalni stroji - Varnost - 11. del: Kombinirani stroji (ISO/DIS 19085-
11:2022)
Woodworking machines - Safety - Part 11: Combined machines (ISO/DIS 19085-
11:2022)
Holzbearbeitungsmaschinen - Sicherheit - Teil 11: Kombinierte Maschinen (ISO/DIS
19085-11:2022)
Machines à bois - Sécurité - Partie 11: Machines combinées (ISO/DIS 19085-11:2022)
Ta slovenski standard je istoveten z: prEN ISO 19085-11
ICS:
13.110 Varnost strojev Safety of machinery
79.120.10 Lesnoobdelovalni stroji Woodworking machines
oSIST prEN ISO 19085-11:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

oSIST prEN ISO 19085-11:2022
oSIST prEN ISO 19085-11:2022
DRAFT INTERNATIONAL STANDARD
ISO/DIS 19085-11
ISO/TC 39/SC 4 Secretariat: UNI
Voting begins on: Voting terminates on:
2022-06-21 2022-09-13
Woodworking machines — Safety —
Part 11:
Combined machines
Machines à bois — Sécurité —
Partie 11: Machines combinées
ICS: 13.110; 79.120.10
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 19085-11:2022(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2022

oSIST prEN ISO 19085-11:2022
ISO/DIS 19085-11:2022(E)
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
oSIST prEN ISO 19085-11:2022
ISO/DIS 19085-11:2022(E)
Contents Page
Foreword .v
Introduction . vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Safety requirements and measures for controls . 6
4.1 Safety and reliability of control systems. 6
4.2 Control devices . 7
4.3 Start . 7
4.3.1 Direct start . 7
4.3.2 Start via control power-on . 8
4.4 Safe stops . 8
4.4.1 General . 8
4.4.2 Normal stop . 8
4.4.3 Operational stop . 8
4.4.4 Emergency stop . 8
4.5 Braking function of tools . 8
4.6 Mode selection . 8
4.7 Tool speed changing . 9
4.7.1 Speed changing by shifting the belts on the pulleys . 9
4.7.2 Speed changing by incremental speed change motor . 9
4.7.3 Infinitely variable speed by frequency inverter . 9
4.7.4 Spindle speed limiting device for tenoning . 9
4.7.5 Changing of the direction of spindle rotation . 9
4.8 Failure of any power supply . 9
4.9 Manual reset control . 9
4.10 Standstill detection and monitoring . 9
4.11 Machine moving parts speed monitoring. 9
4.12 Time delay. 9
4.13 Teleservice . 9
4.14 Power-driven adjustments . 9
5 Safety requirements and measures for protection against mechanical hazards .10
5.1 Stability . 10
5.2 Risk of break-up during operation . 10
5.3 Tool and tool fixing design . 10
5.3.1 General . 10
5.3.2 Spindle locking . 10
5.3.3 Circular saw blade fixing device . 10
5.3.4 Flange dimensions for circular saw blades . 10
5.3.5 Arbor rings/fixing device for milling tools . 11
5.3.6 Quick tool/arbor change system . 11
5.3.7 Manual adjustment of arbor height . 11
5.3.8 Manual adjustment of arbor inclination . 11
5.4 Braking . 11
5.4.1 Braking of tools . 11
5.4.2 Maximum run-down time . 11
5.4.3 Brake release . 11
5.5 Safeguards . 11
5.5.1 Fixed guards . 11
5.5.2 Interlocking movable guards . 11
5.5.3 Hold-to-run control .12
5.5.4 Two hand control .12
iii
oSIST prEN ISO 19085-11:2022
ISO/DIS 19085-11:2022(E)
5.5.5 Electro-sensitive protection equipment (ESPE) .12
5.5.6 Pressure sensitive protection equipment (PSPE) .12
5.6 Prevention of access to hazardous moving parts .12
5.7 Impact hazard .12
5.8 Clamping devices .13
5.9 Measures against ejection . 13
5.9.1 General .13
5.9.2 Guards materials and characteristics . 13
5.9.3 Anti-kickback devices .13
5.10 Workpiece supports and guides . 13
5.11 Safety appliances . 14
5.12 Elements not in use. 14
5.13 Adjustments in tenoning-sawing mode . 14
6 Safety requirements and measures for protection against other hazards .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN ISO 19085-6:2024(Main)
Woodworking machines - Safety - Part 6: Single spindle vertical moulding machines ("toupies") (ISO 19085-6:2024)
EN ISO 19085-6:2024

This document specifies the safety requirements and measures for single spindle vertical moulding machines (defined in 3.1), capable of continuous production use and hereinafter referred to also as “machines”.
The machines are designed to cut solid wood and material with similar physical characteristics to wood.
This document deals with all significant hazards, hazardous situations and events as listed in Annex A, relevant to the machines when they are operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Transport, assembly, dismantling, disabling and scrapping phases have also been taken into account.
This document is also applicable to machines fitted with one or more of the following devices/additional working units, whose hazards have been dealt with:
a)       device to adjust the arbor vertically;
b)       device to tilt the arbor;
c)        device to fit a manually operated tenoning sliding table;
d)       glass bead saw unit;
e)       adjustable table insert;
f)         device for changing the direction of rotation of the spindle;
g)       device for fixing shank mounted tools on the arbor;
h)       interchangeable arbor;
i)         quick tool/arbor change system;
j)         demountable power feed unit;
k)       support for the demountable power feed unit with power-driven adjustments.
This document does not apply to
—     machines equipped with outboard bearings,
—     machines equipped with powered movements of a front extension table and/or a tenoning sliding table.
This document is not applicable to machines intended for use in potentially explosive atmospheres or to machines manufactured prior to the date of its publication.

  • Standard
    71 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 19085-12:2021/A11:2023(Amendment)
Woodworking machines - Safety - Part 12: Tenoning/profiling machines (ISO 19085-12:2021)
EN ISO 19085-12:2021/A11:2023
  • Amendment
    5 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 19085-3:2022(Main)
Woodworking machines - Safety - Part 3: Numerically controlled (NC/CNC) boring and routing machines (ISO 19085-3:2021)
EN ISO 19085-3:2021

This document gives the safety requirements and measures for numerically controlled (NC/CNC)
boring machines, NC/CNC routing machines and NC/CNC boring and routing machines (as defined in
3.2, 3.3 and 3.4), capable of continuous production use, hereinafter referred to as "machines".
This document deals with all significant hazards, hazardous situations and events, listed in Annex A,
relevant to the machines when they are operated, adjusted and maintained as intended and under the
conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also, transport,
assembly, dismantling, disabling and scrapping phases have been taken into account.
This document is also applicable to machines fitted with one or more of the following devices/additional
working units, whose hazards have been dealt with:
— additional working units for sawing, sanding, assembling or dowel inserting;
— fixed or movable workpiece support;
— mechanical, pneumatic, hydraulic or vacuum workpiece clamping;
— automatic tool change devices.
It is also applicable to machines fitted with edge-banding equipment, even if the relevant specific
hazards have not been dealt with.
NOTE For the risk assessment needed for the edge-banding equipment, ISO 19085-17 can be useful.
Machines covered in this document are designed for workpieces consisting of:
— solid wood;
— material with similar physical characteristics to wood (see ISO 19085-1:2021, 3.2);
— gypsum boards, gypsum bounded fibreboards, cardboard;
— matrix engineered mineral boards, silicate boards;
— composite materials with core consisting of polyurethane or mineral material laminated with light
alloy;
— polymer-matrix composite materials and reinforced thermoplastic/thermoset/elastomeric
materials;
— aluminium light alloy profiles;
— aluminium light alloy plates with a maximum thickness of 10 mm;
— composite boards made from the materials listed above.
This document does not deal with specific hazards related to:
— use of grinding wheels;
— ejection through openings guarded by curtains on machines where the height of the opening in the
enclosure above the workpiece support exceeds 700 mm;
— ejection due to failure of milling tools with a cutting circle diameter equal to or greater than 16 mm
and sawing tools not conforming to EN 847-1:2017 and EN 847-2:2017;
— the combination of a single machine being used with other machines (as a part of a line);
— integrated workpiece loading/unloading systems (e.g. robots).
This document is not applicable to:
— single spindle hand fed or integrated fed routing machines;
— machines intended for use in potentially explosive atmosphere;
— machines manufactured prior to its publication.

  • Standard
    96 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 19085-16:2022(Main)
Woodworking machines - Safety - Part 16: Table band saws and band re-saws (ISO 19085-16:2021)
EN ISO 19085-16:2021

This document gives the safety requirements and measures for stationary and displaceable table band saws and band resaws with manual loading and/or unloading, designed to cut wood and materials with similar physical characteristics to wood, hereinafter referred to as “machines”.
NOTE 1   For the definition of displaceable machine, see ISO 19085-1:2017, 3.5.
It deals with all significant hazards, hazardous situations and events as listed in Clause 4, relevant to the machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also, transport, assembly, dismantling, disabling and scrapping phases have been taken into account.
NOTE 2   For relevant but not significant hazards, e.g. sharp edges of the machine frame, see ISO 12100:2010.
It is also applicable to machines fitted with one or more of the following devices/additional working units, whose hazards have been dealt with:
a)   device to tilt the table;
b)   device to tilt the saw unit.
This document does not apply to:
1)   machines driven by combustion engines or power take offs (PTO);
2)   log band sawing machines;
NOTE 3   Log band sawing machines are covered by EN 1807-2.
3)   machines designed for cross-cutting round or irregular shaped work-pieces;
4)   transportable / displaceable machines with a maximum length of the band saw blade of ≤ 2700 mm and a maximum diameter of the powered wheel of ≤ 350 mm;
NOTE 4    Transportable electrically driven machines are covered by the requirements of EN 61029-1:2009 together with EN 61029-2-5:2015.

  • Standard
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 19085-2:2022(Main)
Woodworking machines - Safety - Part 2: Horizontal beam panel circular sawing machines (ISO 19085-2:2021)
EN ISO 19085-2:2021

This document gives the safety requirements and measures for horizontal beam panel circular sawing machines with the saw carriage of the front cutting line mounted below the workpiece support, which are manually and/or powered loaded and manually unloaded, capable of continuous production use, as defined in 3.1 and hereinafter referred to as “machines”.
This document deals with all significant hazards, hazardous situations and events as listed in Annex A, relevant to the machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also, transport, assembly, dismantling, disabling and scrapping phases have been taken into account.
It is also applicable to machines fitted with one or more of the following devices/additional working units, whose hazards have been dealt with:
—    side pressure device;
—    device for powered unloading;
—    unit for scoring;
—    unit for post-formed/soft-formed edge pre-cutting;
—    panel turning device;
—    front side turn table;
—    pushing out device;
—    pneumatic clamping of the saw blade;
—    powered panel loading device;
—    device for grooving by milling tool;
—    one or more additional cutting lines inside the machine for longitudinal and/or head cut (before the transversal cutting line);
—    workpiece vacuum clamping as part of a front side turn table or of a panel loading device;
—    panel pusher;
—    independent panel pushers;
—    additional panel pushers mounted on the panel pusher carriage;
—    additional panel pusher with integrated label printer device;
—    lifting platform;
—    device for automatic loading of thin panels;
—    device for base board unloading by gravity;
—    device for base board powered unloading;
—    device for panel unloading in limited space condition;
—    loading or pre-loading roller conveyors;
—    pressure beam with additional flaps to increase dust extraction efficiency;
—    saw blade cooling system by air or water-air or oil-air;
—    vibrating conveyor with/without trimming unit for offcuts management;
—    predisposition for top loading/unloading by an external system directly on the machine table and/or on the machine preloading roller conveyor and/or on the machine lifting table.
NOTE      base board is a support panel underlying the panel stack, to protect the panels from damages during transportation.
The machines are designed for cutting panels consisting of:
a) solid wood;
b) material with similar physical characteristics to wood (see ISO19085‑1:2021, 2);
c) gypsum boards, gypsum bounded fibreboards;
d) composite materials, with core consisting of e.g. polyurethane or mineral material, laminated with light alloy;
e) cardboard;
f) foam board;
g) matrix engineered mineral boards, silicate boards;
h) polymer‐matrix composite materials and reinforced thermoplastic/thermoset/elastomeric materials;
i) aluminium light alloy plates with a maximum thickness of 10 mm;
j) composite boards made from the materials listed above.
This document does not deal with hazards related to:
—    specific features different from those listed above;
—    the machining of panels with milling tools for grooving;
—    powered unloading of panels;
—    rear half of split pressure beam on the front cutting line;
—    the combination of a single machine being used with any other machine (as part of a line).
It is not applicable to:
—    machines intended for use in potentiall

  • Standard
    56 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 19085-14:2022(Main)
Woodworking machines - Safety - Part 14: Four-sided moulding machines (ISO 19085-14:2021)
EN ISO 19085-14:2021

This part of ISO 19085 gives the safety requirements and measures for stationary four sided moulding machines with a maximum working width of 350 mm and a maximum speed of the integrated workpiece feed of 200 m/min, with electrical and/or electronic control system, hereinafter referred to as “machines” designed to cut solid wood and materials with similar physical characteristics to wood (see ISO 19085-1:2017, 3.2).
It deals with all significant hazards, hazardous situations and events as listed in Clause 4 relevant to machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also, transport, assembly, dismantling,
disabling and scrapping phases are taken into account.
NOTE: For relevant but not significant hazards, e.g. sharp edges of the machine frame, see ISO 12100:2010.
It is also applicable to machines fitted with one or more of the following devices / additional working units, whose hazards have been dealt with:
- universal spindle;
- glass bead saw unit
- fixed or movable work-piece support;
- quick tool changing system
- laser marking unit
- automatic work-piece returner
- in-feed hopper
- in-feed loading table
This part of ISO 19085 does not deal with any hazards related to:
a) in-feed devices other than in-feed hopper and in-feed loading table (magazines, etc.);
NOTE: For mechanical in-feed devices which also prevent access to the in-feed opening, see 6.6.4.
b) out-feed devices (e.g. mechanical handling systems) except for hazards related to ejection from the machine due to climb cutting
c) single machine being used in combination with any other machine (as part of a line);
It is not applicable to machines intended for use in potentially explosive atmosphere and to machines manufactured prior to its publication.

  • Standard
    57 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 19085-15:2022(Main)
Woodworking machines - Safety - Part 15: Presses (ISO 19085-15:2021)
EN ISO 19085-15:2021

This part of ISO 19085 gives the safety requirements and measures for stationary manually loaded and unloaded:
-   cold presses,
-   hot presses,
-   bending presses,
-   edge/face gluing presses,
-   membrane presses,
-   embossing presses,
where pressing force is applied by hydraulic actuators pushing two flat or shaped surfaces against each other, hereinafter referred to as "machines".
It deals with all significant hazards, hazardous situations and events as listed in Clause 4 relevant to machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also transport, assembly, dismantling, disabling and scrapping phases are taken into account.
NOTE:   For relevant but not significant hazards, e.g. sharp edges of the machine frame, see ISO 12100:2010.
It is also applicable to machines fitted with one or more of the following devices/additional working units, whose hazards have been dealt with:
-   Device for hot gluing
-   Device for high frequency gluing
-   Device for high frequency shaping
-   Automatic work-piece loading and unloading system
-   intermediate additional platens
-   work-piece extractor
-   work-piece clamping pressure beam
-   split moveable platens.
The machines are designed to process work-pieces consisting of:
-   solid wood;
-   materials with similar characteristics to wood (see ISO 19085-1:2017, 3.2);
-   honeycomb.
This part of ISO 19085 does not deal with any hazards related to:
-   specific devices that differ from the list above;
-   hot fluid heating systems internal to the machine other than electrical;
-   any hot fluid heating systems external to the machine;
-   operation of taking intermediate platens out and in again;
-   the combination of a single machine being used with any other machine (as part of a line).
It is not applicable to:
-   frame presses;
-   membrane presses where the pressing force is applied by vacuum only;
-   presses for producing chipboard, fibreboard, OSB;
-   machines intended for use in potentially explosive atmosphere;
-   machines manufactured before the date of its publication as an international standard.

  • Standard
    54 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 19085-17:2021(Main)
Woodworking machines - Safety requirements - Part 17: Edge-banding machines fed by chains (ISO 19085-17:2021)
EN ISO 19085-17:2021

This document gives the safety requirements and measures for edge banding machines fed by chains or
belts, with manual loading and unloading and maximum workpiece height capacity of 100 mm, capable
of continuous production use, hereinafter referred as “machines”.
It deals with all significant hazards, hazardous situations and events, listed in Annex A, relevant to the
machines, when operated, adjusted and maintained as intended and under the conditions foreseen by
the manufacturer; reasonably foreseeable misuse has been considered too. Also, transport, assembly,
dismantling, disabling and scrapping phases are taken into account.
The machines are designed to process in one pass one end (single-end machine) or both ends (doubleend
machine) of panels of:
— materials with similar physical characteristics to wood (see ISO 19085-1:2021, 3.2), even with a
core sheet of aluminium light alloy;
— gypsum plaster boards.
Edges to be applied by the machine can be made of:
— paper;
— melamine;
— plastic;
— composite materials;
— aluminium;
— light alloy;
— veneer;
— solid wood.
It is also applicable to machines fitted with one or more of the following devices/working units, whose
hazards have been dealt with:
— hot air banding unit;
— laser banding unit;
— infrared banding unit;
— dynamic processing units;
— sanding belt units;
— milling unit installed out of the integral enclosure at the panel side on single-end machines;
— milling unit installed out of the integral enclosure between machines halves of double-end machines;
— additional fixed or movable workpiece support along the feed;
— additional infeed workpiece support;
— additional outfeed workpiece support;
— in-feed device for transversal loading of panels in single-end machines;
— intermediate workpiece support in double-end machines;
— automatic panel returner in single-end machines;
— automatic tool changing;
— quick tool changing system;
— automatic multiple edges infeed device;
— workpiece heaters.
This document does not deal with any hazards relating to:
a) systems for loading and unloading of the workpiece to a single machine other than automatic panel
returner and infeed and outfeed workpiece supports (e.g. robots);
b) the combination of a single machine being used with other machines (as part of a line);
c) workpiece dividing unit installed out of the integral enclosure and/or whose tools protrude out of
the integral enclosure;
d) plasma banding unit.
It is not applicable to machines intended for use in potentially explosive atmosphere nor manufactured
before the date of its publication.

  • Standard
    62 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 19085-12:2021(Main)
Woodworking machines - Safety - Part 12: Tenoning/profiling machines (ISO 19085-12:2021)
EN ISO 19085-12:2021

This part of ISO 19085 gives the safety requirements and measures for stationary, manually loaded and unloaded:
-   single end tenoning machines with manual feed sliding table,
-   single end tenoning machines with mechanical feed sliding table,
-   single end tenoning and/or profiling machines with mechanical feed,
-   double end tenoning and/or profiling machines with mechanical feed, also designed to be automatically loaded/unloaded,
-   angular systems for tenoning and profiling with mechanical feed,
with maximum work-piece height capacity of 200 mm for single end machines and 500 mm for double end machines, hereinafter referred to as “machines”.
It deals with all significant hazards, hazardous situations and events relevant to machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also transport, assembly, dismantling, disabling and scrapping phases are taken into account.

  • Standard
    66 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 19085-1:2021(Main)
Woodworking machines - Safety - Part 1: Common requirements (ISO 19085-1:20201)
EN ISO 19085-1:2021

This document gives the safety requirements and measures to reduce risks arising during operation,
adjustment, maintenance, transport, assembly, dismantling, disabling and scrapping, related to
woodworking machines capable of continuous production use, hereinafter referred as “machines”.
These safety requirements and measures are those common to most of the machines, when they are
used as intended and under the conditions foreseen by the manufacturer; reasonably foreseeable
misuse has been considered too.
The machines are designed to process solid wood and material with similar physical characteristics to
wood, with hand feed or integrated feed.
This document is intended to be used in conjunction with the other parts of the ISO 19085 series,
applicable to specific machine types. The extent to which all significant hazards of a specific machine
type are covered is indicated in the specific part of the ISO 19085 series relevant to that machine type.
The hazards covered, at least partly, by the requirements of this document, are listed in Annex A.
It is not applicable to machines intended for use in potential explosive atmospheres or to machines
manufactured prior to the date of its publication.

  • Standard
    60 pages
    English language
    sale 10% off
    e-Library read for
    1 day