SIST EN ISO 16321-1:2022/A1:2025

SLOVENSKI STANDARD
01-julij-2025
Zaščita za oči in obraz za poklicno uporabo - 1. del: Splošne zahteve - Dopolnilo
A1 (ISO 16321-1:2021/Amd 1:2024)
Eye and face protection for occupational use - Part 1: General requirements -
Amendment 1 (ISO 16321-1:2021/Amd 1:2024)
Augen- und Gesichtsschutz für berufliche Anwendungen - Teil 1: Allgemeine
Anforderungen - Änderung 1 (ISO 16321-1:2021/Amd 1:2024)
Protection des yeux et du visage à usage professionnel - Partie 1: Exigences générales -
Amendement 1 (ISO 16321-1:2021/Amd 1:2024)
Ta slovenski standard je istoveten z: EN ISO 16321-1:2022/A1:2025
ICS:
13.340.20 Varovalna oprema za glavo Head protective equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 16321-1:2022/A1
EUROPEAN STANDARD
NORME EUROPÉENNE
March 2025
EUROPÄISCHE NORM
ICS 13.340.20
English Version
Eye and face protection for occupational use - Part 1:
General requirements - Amendment 1 (ISO 16321-
1:2021/Amd 1:2024)
Protection des yeux et du visage à usage professionnel Augen- und Gesichtsschutz für berufliche
- Partie 1: Exigences générales - Amendement 1 (ISO Anwendungen - Teil 1: Allgemeine Anforderungen -
16321-1:2021/Amd 1:2024) Änderung 1 (ISO 16321-1:2021/Amd 1:2024)
This amendment A1 modifies the European Standard EN ISO 16321-1:2022; it was approved by CEN on 17 July 2024.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2025 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 16321-1:2022/A1:2025 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of Regulation 2016/425 aimed to be covered . 4
European foreword
This document (EN ISO 16321-1:2022/A1:2025) has been prepared by Technical Committee ISO/TC 94
"Personal safety -- Personal protective equipment" in collaboration with Technical Committee CEN/TC
85 “Eye protective equipment” the secretariat of which is held by AFNOR.
This Amendment to the European Standard EN ISO 16321-1:2022 shall be given the status of a national
standard, either by publication of an identical text or by endorsement, at the latest by September 2025,
and conflicting national standards shall be withdrawn at the latest by March 2028.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a standardization request addressed to CEN by the European
Commission. The Standing Committee of the EFTA States subsequently approves these requests for its
Member States.
For the relationship with EU Legislation, see informative Annex ZA, which is an integral part of this
document.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 16321-1:2021/Amd 1:2024 has been approved by CEN as EN ISO 16321-
1:2022/A1:2025 without any modification.

Annex ZA
(informative)
Relationship between this European Standard and the essential
requirements of Regulation 2016/425 aimed to be covered
This European Standard has been prepared under a Commission’s standardization request (mandate
M/571) to provide one voluntary means of conforming to essential requirements of Regulation
2016/425 C(2020) 7924 final.
Once this standard is cited in the Official Journal of the European Union under that Regulation
2016/425, compliance with the normative clauses of this standard given in Table ZA.1 confers, within
the limits of the scope of this standard, a presumption of conformity with the corresponding essential
requirements of that Regulation 2016/425 and associated EFTA regulations.
Table ZA.1 — Correspondence between this European Standard and Annex II of Regulation
2016/425
Essential Requirements Clause(s)/subclause(s)
Remarks/Notes
of Regulation 2016/425
of this EN
1.1.1 Ergonomics 4.3; 7.2
1.1.2 Level and classes of 6.2; 6.3.1; 6.3.2; 6.3.3; 6.3.4; 6.6;
protection 7.1;7.4; 7.10; 7.11; 7.14; 7.15; 7.16;
7.17; 7.18; 7.19; 7.20; 7.21
1.2.1 Absence of risks and other 5.2, 6.1
'inherent' nuisance factors
1.2.1.1 Suitable constituent 4.2
materials
1.2.1.2 Satisfactory surface 4.3
condition of all PPE parts in
contact with the user.
1.2.1.3 Maximum permissible 5.1; 5.2; 5.3; 5.5; 6.1; 6.5; 6.7; 7.3
user impediment
1.3.1 Adaptation of PPE to user 4.3; 4.5; 5.1; 7.2
morphology
1.3.2 Lightness and design 4.1; 7.4; 7.5; 7.6; 7.7; 7.8, 7.12
strength
1.4 Manufacturer's instructions 9
and information
2.2 PPE "enclosing" the parts of 7.9; 7.13
the body to be protected
2.3 PPE for the face, eyes and 4.3; 5; 6.1; 6.5; 6.7; 7.9; 7.13
respiratory system
2.9 PPE incorporating 4.3
components which can be
adjusted or removed by the user
2.12 PPE bearing one or more 8
identification markings or
indicators directly or indirectly
relating to health and safety
2.14 "Multi risk" PPE 6; 7 This standard describes
multiple types of risks.
The EHSR is covered by
the appropriate
combination of
requirements, associated
with the risks
corresponding to the
intended use of the
eye/face protector
3.1.1 Impact caused by falling or 7.1; 7.4; 7.9; 7.10; 7.11 This standard does not
ejected objects and collision of cover requirements
parts of the body with obstacle concerning prevention of
injuries caused by
collision of the face with
obstacles.
3.6.1 PPE constituent materials 6.3.2; 6.6; 7.5; 7.14; 7.19; 7.4; 7.10.2;
and other components 7.11.2
3.6.2 Complete PPE ready for use 6.3.2; 7.19
3.9.1Non-ionising radiation 6; 7.1; 8; 9
3.10.2 Protection against 7.15; 7.16; 7.17; 7.18; 7.20
cutaneous and ocular contact
Table ZA.2 — Applicable Standards to confer presumption of conformity as described in this
Annex ZA
Column 1 Column 2 Column 3 Column 4
Reference in International
Title Corresponding European
Clause 2 Standard Edition
Standard Edition
ISO 4007 ISO 4007:2018 Personal protective EN ISO 4007:2018
equipment - Eye and face
ISO/CIE 11664-1 ISO/CIE 11664- Colorimetry – Part 1: CIE EN ISO/CIE 11664-1:2019
1:2019 standard colorimetric
observers
ISO/CIE 11664-2 ISO/CIE 11664- Colorimetry – Part 2: CIE EN ISO/CIE 11664-2:2022
2:2022 standard illuminants
ISO 12312-1 ISO 12312-1:2022 Eye and face protection – EN ISO 12312-1:2022
Sunglasses and related
eyewear - Part 1: Sunglasses
for general use
ISO 16034 ISO 16034:2002 Ophthalmic optics — X
Specifications for single-
vision ready-to-wear near-
vision spectacles
ISO 16321-2 ISO 16321-2:2021 Eye and face protection for EN ISO 16321-2:2021
occupational use — Part 2:
Additional requirements for
protectors used during
welding and related
techniques
ISO 16321-3 ISO 16321-3:2021 Eye and face protection for EN ISO 16321-3:2022
occupational use — Part 3:
Additional requirements for
mesh protectors
ISO 18526-1 ISO 18526-1:2020 Eye and face protection — EN ISO 18526-1:2020
Test methods — Part 1:
Geometrical optical
properties
ISO 18526-2 ISO 18526-2:2020 Eye and face protection — EN ISO 18526-2:2020
Test methods — Part 2:
Physical optical properties
ISO 18526-3 ISO 18526-3:2020 Eye and face protection — EN ISO 18526-3:2020
Test methods — Part 3:
Physical and mechanical
properties
ISO 18526-4 ISO 18526-4:2020 Eye and face protection — EN ISO 18526-4:2020
Test methods — Part 4:
Headforms
ISO 21987 ISO 21987:2017 Ophthalmic optics — EN ISO 21987:2017
Mounted spectacle lenses
ISO 80079-36 ISO 80079-36:2016 Explosive atmospheres — EN ISO 80079-36:2016
Part 36: Non-electrical
equipment for explosive
atmospheres — Basic
method and requirements
The documents listed in the Column 1 of Table ZA.2, in whole or in part, are normatively referenced in
this document, i.e. are indispensable for its application. The achievement of the presumption of
conformity is subject to the application of the edition of Standards as listed in Column 4 or, if no
European Standard Edition exists, the International Standard Edition given in Column 2 of Table ZA.2.
WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European
Standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European
Union.
WARNING 2 — Other Union legislation may be applicable to the product(s) falling within the scope of
this standard.
International
Standard
ISO 16321-1
First edition
Eye and face protection for
2021-03
occupational use —
AMENDMENT 1
Part 1:
2024-07
General requirements
AMENDMENT 1
Protection des yeux et du visage à usage professionnel —
Partie 1: Exigences générales
AMENDEMENT 1
Reference number
ISO 16321-1:2021/Amd.1:2024(en) © ISO 2024

ISO 16321-1:2021/Amd.1:2024(en)
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 16321-1:2021/Amd.1:2024(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an e
...