Specifications for particular types of winding wires - Part 62: Polyester glass-fibre wound, silicone resin or varnish impregnated, bare or enamelled rectangular copper wire, temperature index 200 (IEC 60317-62:2020)

This part of IEC 60317 specifies the requirements of polyester glass-fibre wound, silicone
resin or varnish impregnated bare, grade 1 or grade 2 enamelled rectangular copper winding
wires, temperature index 200. The impregnating agent is a silicone containing resin or
varnish.
The range of nominal conductor dimensions covered by this document is:
– width: min. 2,0 mm max. 16,0 mm;
– thickness: min. 0,80 mm max. 5,60 mm.
NOTE For this type of wire, the heat shock test is inappropriate and therefore a heat shock temperature cannot be
established. Consequently, a class based on the requirements for temperature index and heat shock temperature
cannot be specified.

Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten - Teil 62: Flachdrähte aus Kupfer, blank oder lackisoliert und umhüllt mit Polyesterglasgewebe, imprägniert mit Harz oder Lack oder unimprägniert, Temperaturindex 200 (IEC 60317-62:2020)

Spécifications pour types particuliers de fils de bobinage - Partie 62: Fil de section rectangulaire en cuivre nu ou émaillé, guipé de fibres de verre avec polyester de classe d'au moins 200, imprégnées de vernis ou de résine, d'indice de température 200 (IEC 60317-62:2020)

IEC 60317-62:2020 est disponible sous forme de IEC 60317-62:2020 RLV qui contient la Norme internationale et sa version Redline, illustrant les modifications du contenu technique depuis l'édition précédente.

L'IEC 60317-62:2020 spécifie les exigences relatives aux fils de bobinage de section rectangulaire en cuivre nus ou émaillés de grade 1 ou de grade 2, guipés de fibres de verre polyester imprégnées de résine silicone ou de vernis, d'indice de température 200. L'agent d'imprégnation est un vernis ou une résine contenant du silicone. La gamme des dimensions nominales des conducteurs couvertes par le présent document est:
- largeur: min. 2,0 mm max. 16,0 mm;
- épaisseur: min. 0,80 mm max. 5,60 mm.
NOTE Pour ce type de fil, l'essai de choc thermique ne s'applique pas et la température de choc thermique ne peut donc pas être définie. Par conséquent, il n'est pas possible de spécifier une classe fondée sur les exigences d'indice de température et de température de choc thermique.
Cette deuxième édition annule et remplace la première édition parue en 2012. Cette édition constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l’édition précédente:
- révision du titre de la norme pour décrire de manière plus précise la construction du fil;
- révision de l’Article 1, domaine d’application de la norme, afin d’apporter davantage de précisions sur la construction du fil;
- révision du 3.2.2, exigences générales relatives aux fils de bobinage des revêtements en fibre de verre.

Specifikacije za posebne vrste navijalnih žic - 62. del: S poliestrskim steklenim vlaknom povita, s smolo ali posteklino silikonsko impregnirana, gola ali emajlirana pravokotna bakrena žica, temperaturni indeks 200 (IEC 60317-62:2020)

General Information

Status
Published
Publication Date
03-Sep-2020
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
12-Aug-2020
Due Date
17-Oct-2020
Completion Date
04-Sep-2020

Relations

Buy Standard

Standard
EN IEC 60317-62:2020
English language
13 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN IEC 60317-62:2020
01-november-2020
Nadomešča:
SIST EN 60317-62:2012
Specifikacije za posebne vrste navijalnih žic - 62. del: S poliestrskim steklenim
vlaknom povita, s smolo ali posteklino silikonsko impregnirana, gola ali emajlirana
pravokotna bakrena žica, temperaturni indeks 200 (IEC 60317-62:2020)
Specifications for particular types of winding wires - Part 62: Polyester glass-fibre wound,
silicone resin or varnish impregnated, bare or enamelled rectangular copper wire,
temperature index 200 (IEC 60317-62:2020)
Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten - Teil 62:
Flachdrähte aus Kupfer, blank oder lackisoliert und umhüllt mit Polyesterglasgewebe,
imprägniert mit Harz oder Lack oder unimprägniert, Temperaturindex 200 (IEC 60317-
62:2020)
Spécifications pour types particuliers de fils de bobinage - Partie 62: Fil de section
rectangulaire en cuivre nu ou émaillé, guipé de fibres de verre avec polyester de classe
d'au moins 200, imprégnées de vernis ou de résine, d'indice de température 200 (IEC
60317-62:2020)
Ta slovenski standard je istoveten z: EN IEC 60317-62:2020
ICS:
29.060.10 Žice Wires
77.150.30 Bakreni izdelki Copper products
SIST EN IEC 60317-62:2020 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN IEC 60317-62:2020

---------------------- Page: 2 ----------------------
SIST EN IEC 60317-62:2020


EUROPEAN STANDARD EN IEC 60317-62

NORME EUROPÉENNE

EUROPÄISCHE NORM
July 2020
ICS 29.060.10 Supersedes EN 60317-62:2012 and all of its
amendments and corrigenda (if any)
English Version
Specifications for particular types of winding wires - Part 62:
Polyester glass-fibre wound, silicone resin or varnish
impregnated, bare or enamelled rectangular copper wire,
temperature index 200
(IEC 60317-62:2020)
Spécifications pour types particuliers de fils de bobinage - Technische Lieferbedingungen für bestimmte Typen von
Partie 62: Fil de section rectangulaire en cuivre nu ou Wickeldrähten - Teil 62: Flachdrähte aus Kupfer, blank oder
émaillé, guipé de fibres de verre polyester imprégnées de lackisoliert und umhüllt mit Polyesterglasgewebe,
résine silicone ou de vernis, d'indice de température 200 imprägniert mit Harz oder Lack oder unimprägniert,
(IEC 60317-62:2020) Temperaturindex 200
(IEC 60317-62:2020)
This European Standard was approved by CENELEC on 2020-07-15. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN IEC 60317-62:2020 E

---------------------- Page: 3 ----------------------
SIST EN IEC 60317-62:2020
EN IEC 60317-62:2020 (E)
European foreword
The text of document 55/1849/FDIS, future edition 2 of IEC 60317-62, prepared by IEC/TC 55
"Winding wires" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
EN IEC 60317-62:2020.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2021-04-15
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2023-07-15
document have to be withdrawn

This document supersedes EN 60317-62:2012 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.

Endorsement notice
The text of the International Standard IEC 60317-62:2020 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 60264 (series) NOTE Harmonized as EN 60264 (series)
IEC 60317 (series) NOTE Harmonized as EN 60317 (series)
IEC 60851 (series) NOTE Harmonized as EN 60851 (series)


2

---------------------- Page: 4 ----------------------
SIST EN IEC 60317-62:2020
EN IEC 60317-62:2020 (E)
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60317-0-8 2019 Specifications for particular types of winding EN IEC 60317-0-8 2019
wires - Part 0-8: General requirements -
Polyester glass-fibre wound unvarnished and
fused, or resin or varnish impregnated, bare
or enamelled rectangular copper wire


3

---------------------- Page: 5 ----------------------
SIST EN IEC 60317-62:2020

---------------------- Page: 6 ----------------------
SIST EN IEC 60317-62:2020



IEC 60317-62

®


Edition 2.0 2020-06




INTERNATIONAL



STANDARD




NORME


INTERNATIONALE











Specifications for particular types of winding wires –

Part 62: Polyester glass-fibre wound, silicone resin or varnish impregnated, bare

or enamelled rectangular copper wire, temperature index 200



Spécifications pour types particuliers de fils de bobinage –

Partie 62: Fil de section rectangulaire en cuivre nu ou émaillé, guipé de fibres de


verre polyester imprégnées de résine silicone ou de vernis, d'indice de

température 200












INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE


INTERNATIONALE




ICS 29.060.10 ISBN 978-2-8322-8430-8




Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------
SIST EN IEC 60317-62:2020
– 2 – IEC 60317-62:2020 © IEC 2020
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms, definitions, general notes and appearance . 6
3.1 Terms and definitions . 6
3.2 General notes . 6
3.2.1 Methods of test . 6
3.2.2 Winding wire . 7
3.3 Appearance . 7
4 Dimensions. 7
5 Electrical resistance . 7
6 Elongation . 7
7 Springiness . 7
8 Flexibility and adherence . 7
9 Heat shock . 8
10 Cut-through . 8
11 Resistance to abrasion . 8
12 Resistance to solvents . 8
13 Breakdown voltage . 8
14 Continuity of insulation . 8
15 Temperature index . 8
16 Resistance to refrigerants . 8
17 Solderability . 8
18 Heat or solvent bonding . 8
19 Dielectric dissipation factor . 8
20 Resistance to transformer oil . 8
23 Pin hole test . 9
30 Packaging .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.