SIST EN 13029:2010
(Main)Packaging - Light-gauge metal packaging - Apertures for plug-in plastic closures
Packaging - Light-gauge metal packaging - Apertures for plug-in plastic closures
This European Standard specifies the dimensions and profile of the aperture for plug-in plastic closures used in round and non-round metal containers of nominal wall thickness equal to or less than 0,49 mm.
Verpackungen - Feinstblechverpackungen - Öffnungen für aufsteckbare Verschlüsse aus Kunststoff
Diese Europäische Norm legt die Maße und das Profil der Öffnung von aufsteckbaren Verschlüssen der Typen A und B aus Kunststoff fest, die bei runden und nicht runden Metallbehältern mit Nennblechdicken von höchstens 0,49 mm Anwendung finden.
Emballage - Emballages métalliques légers - Ouverture de récipients métalliques équipés de goulots en matière plastique
La présente Norme européenne spécifie les dimensions et le profil de louverture des récipients métalliques
dune épaisseur de paroi nominale inférieure ou égale à 0,49 mm, ronds et non ronds, équipés de goulots en
matière plastique.
Embalaža - Pločevinke - Odprtine za plastične čepe
Ta evropski standard opredeljuje dimenzije in profil odprtin za plastične čepe tipa A in tipa B, ki se uporabljajo v okroglih in neokroglih kovinskih zabojnikih z nazivno debelino sten, enako ali manjšo od 0.49 mm.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Verpackungen - Feinstblechverpackungen - Öffnungen für aufsteckbare Verschlüsse aus KunststoffEmballage - Emballages métalliques légers - Ouverture de récipients métalliques équipés de goulots en matière plastiquePackaging - Light-gauge metal packaging - Apertures for plug-in plastic closures55.120Cans. Tins. TubesICS:Ta slovenski standard je istoveten z:EN 13029:2009SIST EN 13029:2010en,fr,de01-januar-2010SIST EN 13029:2010SLOVENSKI
STANDARDSIST EN 13029:20021DGRPHãþD
SIST EN 13029:2010
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 13029
November 2009 ICS 55.120 Supersedes EN 13029:2001English Version
Packaging - Light-gauge metal packaging - Apertures for plug-in plastic closures
Emballage - Emballages métalliques légers - Ouverture de récipients métalliques équipés de goulots en matière plastique
Verpackungen - Feinstblechverpackungen - Öffnungen für aufsteckbare Verschlüsse aus Kunststoff This European Standard was approved by CEN on 10 October 2009.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13029:2009: ESIST EN 13029:2010
EN 13029:2009 (E) 2
Contents Page Foreword .3Introduction .41Scope .52General requirements .53Dimensions .6Bibliography .9 SIST EN 13029:2010
EN 13029:2009 (E) 3
Foreword This document (EN 13029:2009) has been prepared by Technical Committee CEN/TC 261 “Packaging”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2010, and conflicting national standards shall be withdrawn at the latest by May 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 13029:2001. This edition includes specifications for apertures for a second type of closure. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. SIST EN 13029:2010
EN 13029:2009 (E) 4
Introduction Efficient packaging is of great importance for the distribution and the protection of goods. Insufficient or inappropriate packaging can lead to damage or wastage of the contents of the pack. General use metal containers may be f
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.