iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 12107:1999

(Main)

Plastics piping systems - Injection-moulded thermoplastics fittings, valves and ancillary equipment - Determination of the long-term hydrostatic strength of thermoplastics materials for injection moulding of piping components

Plastics piping systems - Injection-moulded thermoplastics fittings, valves and ancillary equipment - Determination of the long-term hydrostatic strength of thermoplastics materials for injection moulding of piping components

This standard specifies methods for preparing tubular test pieces for testing thermoplastics materials used for injection moulding to evaluate the long-term resistance to constant internal water pressure at constant temperature and to check the material hydrostatic strength.

Kunststoff-Rohrleitungssysteme - Spritzgegossene thermoplastische Formstücke, Armaturen und Zubehörteile - Bestimmung des Zeitstand-Innendruckverhaltens von thermoplastischen Werkstoffen für das Spritzgießen von Rohrleitungsteilen

Diese Norm legt Verfahren für die Vorbereitung rohrförmiger Probekörper zur Prüfung thermoplastischer Werkstoffe fest, die im Spritzgießverfahren eingesetzt werden. Die Prüfung dient der Beurteilung des Zeitstand- Innendruckverhaltens bei konstanter Temperatur und der Überprüfung der Werkstoff-Festigkeit.

Systemes de canalisation en plastique - Raccords, robinets et équipements auxiliaires en thermoplastiques moulés par injection - Détermination de la résistance hydrostatique a long terme des matieres thermoplastiques utilisées pour le moulage par injection des composants de canalisation

La présente norme spécifie des méthodes de préparation des éprouvettes tubulaires pour l'essai des matieres thermoplastiques destinées au moulage par injection. L'essai sert a évaluer leur résistance a long terme a une pression d'eau interne constante, a température constante et a contrôler la résistance hydrostatique de la matiere.

Cevni sistemi iz polimernih materialov - Fitingi, ventili in pribor, oblikovani z injekcijskim vbrizgavanjem - Določanje dolgotrajne hidrostatične trdnosti plastomernih materialov za cevne elemente, ki so oblikovani z injekcijskim vbrizgavanjem

General Information

Status
Withdrawn
Publication Date
30-Jun-1999
Withdrawal Date
06-Mar-2016
ICS
83.140.30 - Plastics pipes and fittings for non fluid use
Technical Committee
PCV - Plastic pipes, fittings and valves
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
04-Mar-2016
Due Date
27-Mar-2016
Completion Date
07-Mar-2016
Directive
89/106/EEC - Construction products
Ref Project
EN 12107:1997 - Plastics piping systems - Injection-moulded thermoplastics fittings, valves and ancillary equipment - Determination of the long-term hydrostatic strength of thermoplastics materials for injection moulding of piping components

Buy Standard

EN 12107:1999EN 12107:1999
PreviousNext
Standard
EN 12107:1999
English language
8 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.WUGQRVWLHNFLMVNLPYEUL]JDYDQMHPKunststoff-Rohrleitungssysteme - Spritzgegossene thermoplastische Formstücke, Armaturen und Zubehörteile - Bestimmung des Zeitstand-Innendruckverhaltens von thermoplastischen Werkstoffen für das Spritzgießen von RohrleitungsteilenSystemes de canalisation en plastique - Raccords, robinets et équipements auxiliaires en thermoplastiques moulés par injection - Détermination de la résistance hydrostatique a long terme des matieres thermoplastiques utilisées pour le moulage par injection des composants de cana
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST-TS CEN/TS 14541-2:2022(Main)
Plastics pipes and fittings - Utilisation of thermoplastics recyclates - Part 2: Recommendations for relevant characteristics
CEN/TS 14541-2:2022

This document provides guidance and information for drafting product standards to specify characteristics and test methods for the utilisation of thermoplastics recyclates (PVC-U, PVC-C, PE, PP, ABS) in pipes, fittings and ancillaries for thermoplastics piping systems.
This document covers recyclates with an agreed specification from all sources.
Note 1: This document does not cover characteristics for reworked material
Note 2: This document does not cover recycling processes (e.g. chemical or mechanical)
Note 3: This document does not define if recycled material can be used in a specific application. The possible use of recyclates will be defined in the applicable product standard.
This document provides guidance about the relevant characteristics to be included in the agreed specification for recyclates.
This document is applicable without prejudice to any existing legislation.
For the recycling process, transport, the testing and the use of thermoplastics recyclates National and/or European regulations (e.g. hygienic aspects) may apply.
Note 4: For example threshold levels for substances of very high concern (SVHC) as defined in the REACH-legislation which can possibly be present in thermoplastic recyclates.

  • Technical specification
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 14541-1:2022(Main)
Plastics pipes and fittings - Utilisation of thermoplastics recyclates - Part 1: Vocabulary
EN 14541-1:2022

This document specifies the general terms and definitions relevant for the utilisation of thermoplastics recyclates in thermoplastics pipes, fittings and ancillaries for both pressure and non-pressure piping systems.
This document is intended to be used by specification writers in conjunction with prCEN/TR 14541-2 and prCEN/TR 14541-3 when preparing normative documents under the scope of CEN/TC 155.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 16486-4:2022(Main)
Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 4: Valves (ISO 16486-4:2022)
EN ISO 16486-4:2022

This part of ISO 16486 specifies the characteristics of valves made from unplasticized polyamide (PA-U) in accordance with ISO 16486 1, intended to be buried and used for the supply of gaseous fuels.
Valves made from other material than unplasticized polyamide designed for the supply of gaseous fuels conforming to the relevant standards are permitted to be used in PA-U piping system according to ISO 16486 provided they have relevant PA-U connections for butt fusion or electrofusion ends (see ISO 164863). The component, i.e. the complete valve, shall fulfil the requirements of this part of ISO 16486.
It also specifies the test parameters for the test methods referred to in this part of ISO 16486.
It is applicable to bi-directional valves with spigot end or electrofusion socket intended to be jointed with PA-U pipes conforming to ISO 16486 2 without any fittings or with PA-U fittings conforming to ISO 164863.
This part of ISO 16486 covers valves for pipes with a nominal outside diameter, dn, ≤250 mm.

  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST-TS CEN/TS 1555-7:2022(Main)
Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 7: Guidance for the assessment of conformity
CEN/TS 1555-7:2021

This Technical Specification gives guidance for the assessment of conformity of compounds, products, joints and assemblies in accordance with the applicable part(s) of FprEN 1555 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of certification procedures.
It is recommended that the quality management system conforms to or isF no less stringent than the relevant requirements to EN ISO 9001 [2].
NOTE 1   If certification is involved, the certification and inspection body is preferably compliant with EN 45011 [3], EN 45012 [4] or EN ISO/IEC 17020 [5], as applicable.
In conjunction with Parts 1 to 5 of EN 1555 (see Foreword), this Technical Specification is applicable to polyethylene (PE) plastics piping systems for the supply of gaseous fuels. It is applicable to PE pipes, fittings, and valves, their joints and to joints with components of other materials intended to be used under the following conditions:
a)   a maximum operating pressure, MOP, up to and including 10 bar );
b)   an operating temperature of 20 °C as reference temperature.
NOTE 2   For other operating temperatures, derating coefficients can be used; see EN 1555-5.
For mechanical fittings conforming to ISO 17885, guidance for assessment of conformity is not given in this part of EN 1555. When requested, a quality plan based on the tests mentioned should be set up in agreement between user and manufacturer.
EN 1555 covers a range of maximum operating pressures and gives requirements concerning colours and additives.
NOTE 3   It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.

  • Technical specification
    43 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1555-2:2021(Main)
Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 2: Pipes
EN 1555-2:2021

This part of EN 1555 specifies the characteristics of pipes made from polyethylene (PE) for piping systems in the field of the supply of gaseous fuels.
It also specifies the test parameters for the test methods referred to in this standard.
In conjunction with Parts 1 and 3 to 5 of EN 1555, it is applicable to PE pipes, their joints and to joints with components of PE and other materials intended to be used under the following conditions:
a)    a maximum operating pressure, MOP, up to and including 10 bar 1);
b)   an operating temperature of 20 °C as reference temperature.
NOTE 1   For other operating temperatures, derating coefficients should be used, see FprEN 1555-5.
EN 1555 covers a range of maximum operating pressures and gives requirements concerning colours and additives.
It covers three types of pipe:
-   PE pipes (outside diameter dn) including any identification stripes;
-   PE pipes with co-extruded layers on either or both the outside and/or inside of the pipe (total outside diameter dn) as specified in Annex A, where all layers have the same MRS rating;
-   PE pipes (outside diameter dn) with a peelable, contiguous thermoplastics additional layer on the outside of the pipe (‘coated pipe’) as specified in Annex B.
NOTE 2   It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1555-4:2021(Main)
Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 4: Valves
EN 1555-4:2021

This European Standard specifies the characteristics of valves made from polyethylene (PE) for piping systems in the field of the supply of gaseous fuels.
NOTE 1   Valves made from other material than polyethylene designed for the supply of gaseous fuels conforming to the relevant standards are permitted to be used in PE piping system according to EN 1555 provided they have relevant PE connection for butt fusion or electrofusion ends (see EN 1555 3).
It also specifies the test parameters for the test methods referred to in this standard.
In conjunction with Parts 1, 2, 3 and 5 of EN 1555, it is applicable to PE valves, their joints and to joints with components of PE and other materials intended to be used under the following conditions:
a) a maximum operating pressure, MOP, up to and including 10 bar  );
b) an operating temperature of 20 °C as reference temperature;
NOTE 2   For other operating temperatures, derating coefficients should be used, see EN 1555 5.
c) an operating temperature between -20 °C and +40 °C.
EN 1555 covers a range of maximum operating pressures and gives requirements concerning colours and additives.
NOTE 3   It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
It is applicable to bi-directional valves with spigot end or electrofusion socket intended to be fused with PE pipes conforming to EN 1555 2 without any fittings or with PE fittings conforming to EN 1555 3.
This European Standard covers valves for pipes with a nominal outside diameter dn  315 mm.

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1555-3:2021(Main)
Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 3: Fittings
EN 1555-3:2021

This document specifies the characteristics of fusion fittings made from polyethylene (PE) as well as of mechanical fittings for piping systems in the field of the supply of gaseous fuels.
It also specifies the test parameters for the test methods referred to in this standard.
In conjunction with Parts 1, 2, 4 and 5 of EN 1555, it is applicable to PE fittings, their joints and to joints with components of PE and other materials intended to be used under the following conditions:
a)   a maximum operating pressure, MOP, up to and including 10 bar;
b)   an operating temperature of 20 °C as reference temperature.
NOTE 1   For other operating temperatures, derating coefficients should be used; see EN 1555-5.
EN 1555 (all parts) covers a range of maximum operating pressures and gives requirements concerning colours and additives.
NOTE 2   It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
This document is applicable for fittings of the following types:
c)   electrofusion socket fittings;
d)   electrofusion saddle fittings;
e)   spigot end fittings (for butt fusion using heated tools and electrofusion socket fusion);
f)   mechanical fittings.
The fittings can e.g. be in the form of couplers, equal and reduced tees, reducers, bends or caps.

  • Standard
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1555-5:2021(Main)
Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 5: Fitness for purpose of the system
EN 1555-5:2021

This part of EN 1555 specifies requirements of fitness for purpose of the polyethylene (PE) piping system in the field of the supply of gaseous fuels.
It specifies the definitions of electrofusion, butt fusion and mechanical joints.
It specifies the method of preparation of test piece joints, and the tests to be carried out on these joints for assessing the fitness for purpose of the system under normal and extreme conditions.
It specifies the test parameters for the test methods referred to in this document.
NOTE 1   This document is intended only to be used by the product manufacturer to assess the performance of components according to EN 1555-2, EN 1555-3, and/or EN 1555-4 when joined together under normal and extreme conditions in accordance with this document. It is not intended for on-site testing of pipe systems.
In conjunction with Parts 1 to 4 of EN 1555, it is applicable to PE pipes, fittings, valves, their joints and to joints with components of other materials intended to be used under the following conditions:
a)   a maximum operating pressure, MOP, up to and including 10 bar  ;
b)   an operating temperature of 20 °C as reference temperature.
NOTE 2   For other operating temperatures, derating coefficients can be used, see Annex A.
EN 1555 (all parts) covers a range of maximum operating pressures and gives requirements concerning colours and additives.
NOTE 3   It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1555-1:2021(Main)
Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 1: General
EN 1555-1:2021

This part of EN 1555 specifies the general aspects of polyethylene (PE) piping systems in the field of the supply of gaseous fuels.
It also specifies the test parameters for the test methods referred to in this standard.
In conjunction with Parts 2 to 5 of EN 1555 it is applicable to PE pipes, fittings, and valves, their joints and to joints with components of other materials intended to be used under the following conditions:
a)   a maximum operating pressure, MOP, up to and including 10 bar  );
b)   an operating temperature of 20 °C as reference temperature.
NOTE 1   For other operating temperatures, derating coefficients should be used, see EN 1555-5 [6].
EN 1555 (all parts) covers a range of maximum operating pressures and gives requirements concerning colours and additives.
NOTE 2   It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 16486-5:2021(Main)
Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 5: Fitness for purpose of the system (ISO 16486-5:2021)
EN ISO 16486-5:2021

This part of ISO 16486 specifies the requirements of fitness for purpose of the unplasticized polyamide (PA-U) piping system, intended to be buried and used for the supply of gaseous fuels. It also specifies the definitions of electrofusion and butt fusion joints.
This part of ISO 16486 specifies the method of preparation of test piece joints and the tests to be carried out on these joints for assessing the fitness for purpose of the system under normal and extreme conditions. It also specifies the test parameters for the test methods to which it refers.
ISO 16486 is applicable to PA-U piping systems the components of which are connected by fusion jointing and/or mechanical jointing.
In conjunction with the other parts of ISO 16486, it is applicable to PA-U fittings, their joints and to joints with components of PA-U.

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day