SIST EN IEC 61300-2-54:2020

SLOVENSKI STANDARD
SIST EN IEC 61300-2-54:2020
01-marec-2020
Optični spojni elementi in pasivne komponente - Osnovni preskusni in merilni
postopki - 2-54. del: Preskusi - Jedko ozračje (mešanica plinov) (IEC 61300-2-
54:2019)
Fibre optic interconnecting devices and passive components - Basic test and
measurement procedures - Part 2-54: Tests - Corrosive atmosphere (mixed gas) (IEC
61300-2-54:2019)
Lichtwellenleiter - Verbindungselemente und passive Bauteile - Grundlegende Prüf- und
Messverfahren - Teil 2-54: Prüfungen - Corrosive atmosphere (mixed gas) (IEC 61300-2-
54:2019)
Dispositifs d’interconnexion et composants passifs fibroniques - Méthodes
fondamentales d'essais et de mesures - Partie 2-54: Essais - Atmosphere corrosive
(melange de gaz) (IEC 61300-2-54:2019)
Ta slovenski standard je istoveten z: EN IEC 61300-2-54:2019
ICS:
33.180.20 Povezovalne naprave za Fibre optic interconnecting
optična vlakna devices
SIST EN IEC 61300-2-54:2020 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN IEC 61300-2-54:2020

---------------------- Page: 2 ----------------------
SIST EN IEC 61300-2-54:2020


EUROPEAN STANDARD EN IEC 61300-2-54

NORME EUROPÉENNE

EUROPÄISCHE NORM
December 2019
ICS 33.180.20

English Version
Fibre optic interconnecting devices and passive components -
Basic test and measurement procedures - Part 2-54: Tests -
Corrosive atmosphere (mixed gas)
(IEC 61300-2-54:2019)
Dispositifs d’interconnexion et composants passifs Lichtwellenleiter - Verbindungselemente und passive
fibroniques - Méthodes fondamentales d'essais et de Bauteile - Grundlegende Prüf- und Messverfahren - Teil 2-
mesures - Partie 2-54: Essais - Atmosphere corrosive 54: Prüfungen - Korrosionsatmosphäre (Mischgas)
(melange de gaz) (IEC 61300-2-54:2019)
(IEC 61300-2-54:2019)
This European Standard was approved by CENELEC on 2019-12-18. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN IEC 61300-2-54:2019 E

---------------------- Page: 3 ----------------------
SIST EN IEC 61300-2-54:2020
EN IEC 61300-2-54:2019 (E)
European foreword
The text of document 86B/4232/FDIS, future edition 1 of IEC 61300-2-54, prepared by SC 86B "Fibre
optic interconnecting devices and passive components" of IEC/TC 86 "Fibre optics" was submitted to
the IEC-CENELEC parallel vote and approved by CENELEC as EN IEC 61300-2-54:2019.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2020-09-18
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2022-12-18
document have to be withdrawn

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.

Endorsement notice
The text of the International Standard IEC 61300-2-54:2019 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 61753-1 NOTE Harmonized as EN IEC 61753-1
IEC 61753-1-3 NOTE Harmonized as EN 61753-1-3


2

---------------------- Page: 4 ----------------------
SIST EN IEC 61300-2-54:2020
EN IEC 61300-2-54:2019 (E)
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60068-2-60 -  Environmental testing - Part 2-60: Tests - EN 60068-2-60 -
Test Ke: Flowing mixed gas corrosion test
IEC 61300-1 -  Fibre optic interconnecting devices and EN 61300-1 -
passive components - Basic test and
measurement procedures - Part 1: General
and guidance
IEC 61300-3-1 -  Fibre optic interconnecting devices and EN 61300-3-1 -
passive components - Basic test and
measurement procedures - Part 3-1:
Examinations and measurements - Visual
examination
IEC 61300-3-4 -  Fibre optic interconnecting devices and EN 61300-3-4 -
passive components - Basic test and
measurement procedures - Part 3-4:
Examinations and measurements -
Attenuation
IEC 61300-3-6 -  Fibre optic interconnecting devices and EN 61300-3-6 -
passive components - Basic test and
measurement procedures - Part 3-6:
Examinations and measurements - Return
loss

3

---------------------- Page: 5 ----------------------
SIST EN IEC 61300-2-54:2020

---------------------- Page: 6 ----------------------
SIST EN IEC 61300-2-54:2020



IEC 61300-2-54

®


Edition 1.0 2019-11




INTERNATIONAL



STANDARD



















Fibre optic interconnecting devices and passive components – Basic test and

measurement procedures –

Part 2-54: Tests – Corrosive atmosphere (mixed gas)


























INTERNATIONAL

ELECTROTECHNICAL


COMMISSION





ICS 33.180.20 ISBN 978-2-8322-7594-8




  Warning! Make sure that you obtained this publication from an authorized distributor.


® Registered trademark of the International Electrotechnical Commission

---------------------- Page: 7 ----------------------
SIST EN IEC 61300-2-54:2020
– 2 – IEC 61300-2-54:2019 © IEC 2019
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 General description . 5
5 Apparatus . 6
6 Procedure . 6
6.1 Description of the DUT . 6
6.2 Initial examination and measurement . 6
6.3 Preconditioning . 7
6.4 Conditioning . 7
6.5 Recovery . 7
6.6 Final examinations and measurements . 7
7 Severity . 7
8 Details to be specified . 8
Bibliography . 9

HD
Table 1 – Severity for category I . 8

---------------------- Page: 8 ----------------------
SIST EN IEC 61300-2-54:2020
IEC 61300-2-54:2019 © IEC 2019 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

FIBRE OPTIC INTERCONNECTING
DEVICES AND PASSIVE COMPONENTS –
BASIC TEST AND MEASUREMENT PROCEDURES –

Part 2-54: Tests – Corrosive atmosphere (mixed gas)

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the
...