SIST EN ISO 5183-1:2001

SLOVENSKI STANDARD
01-maj-2001
1DGRPHãþD
SIST EN 25183-1:1998
2SUHPD]DHOHNWURXSRURYQRYDUMHQMH'UåDODHOHNWURG]]XQDQMLPNRQXVRP
GHO.RQLþQDSULWUGLWHYNRQXV,62
Resistance welding equipment - Electrode adaptors, male taper 1:10 - Part 1: Conical
fixing, taper 1:10 (ISO 5183-1:1998)
Widerstandsschweißeinrichtungen - Elektrodenschäfte mit Außenkegel 1:10 - Teil 1:
Kegelige Befestigung, Kegel 1:10 (ISO 5183-1:1998)
Equipement de soudage par résistance - Allonges d'électrode a embout amovible, cône
mâle 1:10 - Partie 1: Emmanchement conique 1:10 (ISO 5183-1:1998)
Ta slovenski standard je istoveten z: EN ISO 5183-1:2000
ICS:
25.160.30 Varilna oprema Welding equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

INTERNATIONAL ISO
STANDARD 5183-1
Second edition
1998-09-01
Resistance welding equipment — Electrode
adaptors, male taper 1:10 —
Part 1:
Conical fixing, taper 1:10
Équipement de soudage par résistance — Allonges d’électrode à embout
amovible, cône mâle 1:10 —
Partie 1: Emmanchement conique 1:10
A
Reference number
ISO 5183-1:1998(E)
ISO 5183-1:1998(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Publication as an International Standard requires approval by at least 75 % of the national bodies casting a vote.
International Standard ISO 5183-1 was prepared by Technical Committee ISO/TC 44, Welding and allied
processes, Subcommittee SC 6, Resistance welding.
ISO 5183 consists of the following parts, under the general title Resistance welding equipment — Electrode
adaptors, male taper 1:10:
— Part 1: Conical fixing, taper 1:10
— Part 2: Parallel shank fixing for end-thrust electrodes
This second edition is a revision of the first edition (ISO 5183-1:1988), which has been technically revised.
Annexes A and B of this part of ISO 5183 are for information only.
©  ISO 1998
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case postale 56 • CH-1211 Genève 20 • Switzerland
Internet iso@iso.ch
Printed in Switzerland
ii
© ISO
ISO 5183-1:1998(E)
Introduction
This part of ISO 5183 is an updated edition of ISO 5183-1:1988 and is largely based on the former version.
It is extended to adaptors with longer taper fits (type C) conforming to ISO 1089:1980, type B.
These electrode adaptors are designed to be used when electrodes are mounted at an angle.
iii
INTERNATIONAL STANDARD  © ISO ISO 5183-1:1998(E)
Resistance welding equipment — Electrode adaptors, male
taper 1:10 —
Part 1:
Conical fixing, taper 1:10
1 Scope
This part of ISO 5183 specifies the dimensions and tolerances of resistance spot welding electrode adaptors where
the fix
...