SIST EN 301 908-3 V13.1.1:2019

Final draft ETSI EN 301 908-3 V13.1.0 (2019-07)






HARMONISED EUROPEAN STANDARD
IMT cellular networks;
Harmonised Standard for access to radio spectrum;
Part 3: CDMA Direct Spread (UTRA FDD) Base Stations (BS)

---------------------- Page: 1 ----------------------
2 Final draft ETSI EN 301 908-3 V13.1.0 (2019-07)



Reference
REN/MSG-TFES-13-3
Keywords
3G, 3GPP, cellular, digital, E-UTRA, IMT,
IMT-2000, IMT-Advanced, LTE, mobile, radio,
regulation, UMTS, UTRA, WCDMA

ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2019.
All rights reserved.

DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.

3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 Final draft ETSI EN 301 908-3 V13.1.0 (2019-07)

Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 7
Introduction . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 9
3 Definition of terms, symbols and abbreviations . 9
3.1 Terms . 9
3.2 Symbols . 12
3.3 Abbreviations . 13
4 Technical requirements specifications . 14
4.1 Environmental profile . 14
4.2 Conformance requirements . 14
4.2.1 Introduction. 14
4.2.2 Spectrum emissions mask . 17
4.2.2.1 Definition . 17
4.2.2.2 Limit . 17
4.2.2.3 Conformance . 23
4.2.3 Adjacent channel leakage power ratio (ACLR) . 24
4.2.3.1 Definition . 24
4.2.3.2 Limits . 24
4.2.3.3 Cumulative ACLR test requirement in non-contiguous spectrum or multiple-bands . 25
4.2.3.4 Conformance . 26
4.2.4 Transmitter spurious emis sions . 26
4.2.4.1 Definition . 26
4.2.4.2 Limits . 27
4.2.4.2.1 Spurious emissions . 27
4.2.4.2.2 Co-existence with other systems . 27
4.2.4.2.3 Co-existence with services in adjacent frequency bands . 29
4.2.4.2.4 Protection of the BS receiver of own or different BS . 29
4.2.4.2.5 Co-existence with Home BS operating in other bands . 30
4.2.4.3 Conformance . 30
4.2.5 Base Station maximum output power . 30
4.2.5.1 Definition . 30
4.2.5.2 Limit . 30
4.2.5.3 Conformance . 31
4.2.6 Transmitter intermodulation . 31
4.2.6.1 Definition . 31
4.2.6.2 Limit . 32
4.2.6.3 Conformance . 32
4.2.7 Receiver spurious emissions . 32
4.2.7.1 Definition . 32
4.2.7.2 Limit . 32
4.2.7.3 Conformance . 33
4.2.8 Blocking characteristics . 33
4.2.8.1 Definition . 33
4.2.8.2 Limit . 33
4.2.8.3 Conformance . 37
4.2.9 Receiver intermodulation characteristics . 37
ETSI

---------------------- Page: 3 ----------------------
4 Final draft ETSI EN 301 908-3 V13.1.0 (2019-07)
4.2.9.1 Definition . 37
4.2.9.2 Limit . 37
4.2.9.3 Conformance . 39
4.2.10 Receiver adjacent channel selectivity . 39
4.2.10.1 Definition . 39
4.2.10.2 Limit . 39
4.2.10.3 Conformance . 40
4.2.11 Home BS output power for adjacent channel protection . 40
4.2.11.1 Definition . 40
4.2.11.2 Limit . 40
4.2.11.3 Conformance . 41
4.2.12 Reference sensitivity level . 41
4.2.12.1 Definition . 41
4.2.12.2 Limit . 41
4.2.12.3 Conformance . 41
5 Testing for compliance with technical requirements . 41
5.1 Environmental conditions for testing . 41
5.2 Interpretation of the measurement results . 42
5.3 Essential radio test suites . 42
5.3.0 Introduction. 42
5.3.1 Spectrum emission mask . 43
5.3.1.0 General . 43
5.3.1.1 Initial conditions . 43
5.3.1.2 Procedures . 43
5.3.1.3 Test requirement . 43
5.3.2 Adjacent channel leakage power ratio (ACLR) . 44
5.3.2.1 Initial conditions . 44
5.3.2.2 Procedure . 44
5.3.2.3 Test requirement . 44
5.3.3 Transmitter spurious emis sions . 45
5.3.3.0 General . 45
5.3.3.1 Initial conditions . 45
5.3.3.2 Procedure . 45
5.3.3.3 Test requirement . 45
5.3.4 Base Station maximum output power . 45
5.3.4.0 General . 45
5.3.4.1 Initial conditions . 46
5.3.4.2 Procedure . 46
5.3.4.3 Test requirement . 46
5.3.5 Transmit intermodulation . 46
5.3.5.0 General . 46
5.3.5.1 Initial conditions . 46
5.3.5.2 Procedures . 47
5.3.5.3 Test requirement . 47
5.3.6 Receiver spurious emissions . 48
5.3.6.0 General . 48
5.3.6.1 Initial conditions . 48
5.3.6.2 Procedure . 48
5.3.6.3 Test requirement . 48
5.3.7 Blocking characteristics . 49
5.3.7.0 General . 49
5.3.7.1 Initial conditions . 49
5.3.7.2 Procedure . 50
5.3.7.3 Test requirement . 50
5.3.8 Receiver intermodulation characteristics . 50
5.3.8.0 General . 50
5.3.8.1 Initial conditions . 50
5.3.8.2 Procedures . 50
5.3.8.3 Test requirement . 51
5.3.9 Receiver adjacent channel selectivity (ACS) . 51
5.3.9.0 General . 51
ETSI

---------------------- Page: 4 ----------------------
5 Final draft ETSI EN 301 908-3 V13.1.0 (2019-07)
5.3.9.1 Initial conditions . 51
5.3.9.2 Procedure . 51
5.3.9.3 Test requirement . 52
5.3.10 Home BS output power for adjacent channel protection . 52
5.3.10.1 Initial conditions . 52
5.3.10.2 Procedure . 52
5.3.10.3 Test requirement . 53
5.3.11 Reference sensitivity level . 53
5.3.11.0 General . 53
5.3.11.1 Initial Conditions . 53
5.3.11.2 Procedure . 53
5.3.11.3 Test requirement . 54
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 55
Annex B (normative): Base Stat ion configurations . 57
B.1 Receiver diversity . 57
B.2 Duplexers . 57
B.3 Power supply options . 57
B.4 Ancillary RF amplifiers . 58
B.5 BS using antenna arrays . 58
B.5.0 Introduction . 58
B.5.1 Receiver tests . 59
B.5.2 Transmitter tests . 59
B.6 Transmit diversity and MIMO transmission . 59
B.7 BS with integrated Iuant BS modem . 60
Annex C (informative): Recommended maximum measurement uncertainty . 61
Annex D (informative): Bibliography . 63
Annex E (informative): Change history . 64
History . 65


ETSI

---------------------- Page: 5 ----------------------
6 Final draft ETSI EN 301 908-3 V13.1.0 (2019-07)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This final draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee Mobile
Standards Group (MSG), and is now submitted for the Vote phase of the ETSI standards EN Approval Procedure.
For non EU countries the present document may be used for regulatory (Type Approval) purposes.
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.1] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.2].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A-1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated
EFTA regulations.
The present document is part 3 of a multi-part deliverable. Full details of the entire series can be found in part 1 [i.5].
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa


ETSI

---------------------- Page: 6 ----------------------
7 Final draft ETSI EN 301 908-3 V13.1.0 (2019-07)
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
The present document is part of a set of standards developed by ETSI that are designed to fit in a modular structure to
cover radio equipment within the scope of the Radio Equipment Directive [i.2]. The present document is produced
following the guidance in ETSI EG 203 336 [i.3] as applicable.

ETSI

---------------------- Page: 7 ----------------------
8 Final draft ETSI EN 301 908-3 V13.1.0 (2019-07)
1 Scope
The present document specifies technical characteristics and methods of measurements for the equipment:
• Stations for IMT 2000 CDMA Direct Spread (UTRA FDD).
- This radio equipment type is capable of operating in all or any part of the frequency bands given in
table 1-1.
Table 1-1: UTRA FDD Base Station operating bands
UTRA FDD Direction of transmission UTRA FDD Base Station operating bands
band
I Transmit 2 110 MHz to 2 170 MHz
Receive 1 920 MHz to 1 980 MHz
III Transmit 1 805 MHz to 1 880 MHz
Receive 1 710 MHz to 1 785 MHz
VII Transmit 2 620 MHz to 2 690 MHz
Receive 2 500 MHz to 2 570 MHz
VIII Transmit 925 MHz to 960 MHz
Receive 880 MHz to 915 MHz
XX Transmit 791 MHz to 821 MHz
Receive
...

SLOVENSKI STANDARD
SIST EN 301 908-3 V13.1.1:2019
01-december-2019
Celična omrežja IMT - Harmonizirani standard za dostop do radijskega spektra - 3.
del: Bazne postaje s CDMA z neposrednim razprševanjem (“Direct Spread”) (UTRA
FDD)
IMT cellular networks - Harmonised Standard for access to radio spectrum - Part 3:
CDMA Direct Spread (UTRA FDD) Base Stations (BS)
Ta slovenski standard je istoveten z: ETSI EN 301 908-3 V13.1.1 (2019-09)
ICS:
33.060.99 Druga oprema za radijske Other equipment for
komunikacije radiocommunications
33.070.99 Druge mobilne storitve Other mobile services
SIST EN 301 908-3 V13.1.1:2019 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 301 908-3 V13.1.1:2019

---------------------- Page: 2 ----------------------
SIST EN 301 908-3 V13.1.1:2019
ETSI EN 301 908-3 V13.1.1 (2019-09)






HARMONISED EUROPEAN STANDARD
IMT cellular networks;
Harmonised Standard for access to radio spectrum;
Part 3: CDMA Direct Spread (UTRA FDD) Base Stations (BS)

---------------------- Page: 3 ----------------------
SIST EN 301 908-3 V13.1.1:2019
 2 ETSI EN 301 908-3 V13.1.1 (2019-09)



Reference
REN/MSG-TFES-13-3
Keywords
3G, 3GPP, cellular, digital, E-UTRA, IMT,
IMT-2000, IMT-Advanced, LTE, mobile, radio,
regulation, UMTS, UTRA, WCDMA

ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2019.
All rights reserved.

DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.

3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI

---------------------- Page: 4 ----------------------
SIST EN 301 908-3 V13.1.1:2019
 3 ETSI EN 301 908-3 V13.1.1 (2019-09)

Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 7
Introduction . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 9
3 Definition of terms, symbols and abbreviations . 9
3.1 Terms . 9
3.2 Symbols . 12
3.3 Abbreviations . 13
4 Technical requirements specifications . 14
4.1 Environmental profile . 14
4.2 Conformance requirements . 14
4.2.1 Introduction. 14
4.2.2 Spectrum emissions mask . 17
4.2.2.1 Definition . 17
4.2.2.2 Limit . 17
4.2.2.3 Conformance . 23
4.2.3 Adjacent channel leakage power ratio (ACLR) . 24
4.2.3.1 Definition . 24
4.2.3.2 Limits . 24
4.2.3.3 Cumulative ACLR test requirement in non-contiguous spectrum or multiple-bands . 25
4.2.3.4 Conformance . 26
4.2.4 Transmitter spurious emis sions . 26
4.2.4.1 Definition . 26
4.2.4.2 Limits . 27
4.2.4.2.1 Spurious emissions . 27
4.2.4.2.2 Co-existence with other systems . 27
4.2.4.2.3 Co-existence with services in adjacent frequency bands . 29
4.2.4.2.4 Protection of the BS receiver of own or different BS . 29
4.2.4.2.5 Co-existence with Home BS operating in other bands . 30
4.2.4.3 Conformance . 30
4.2.5 Base Station maximum output power . 30
4.2.5.1 Definition . 30
4.2.5.2 Limit . 30
4.2.5.3 Conformance . 31
4.2.6 Transmitter intermodulation . 31
4.2.6.1 Definition . 31
4.2.6.2 Limit . 32
4.2.6.3 Conformance . 32
4.2.7 Receiver spurious emissions . 32
4.2.7.1 Definition . 32
4.2.7.2 Limit . 32
4.2.7.3 Conformance . 33
4.2.8 Blocking characteristics . 33
4.2.8.1 Definition . 33
4.2.8.2 Limit . 33
4.2.8.3 Conformance . 37
4.2.9 Receiver intermodulation characteristics . 37
ETSI

---------------------- Page: 5 ----------------------
SIST EN 301 908-3 V13.1.1:2019
 4 ETSI EN 301 908-3 V13.1.1 (2019-09)
4.2.9.1 Definition . 37
4.2.9.2 Limit . 37
4.2.9.3 Conformance . 39
4.2.10 Receiver adjacent channel selectivity . 39
4.2.10.1 Definition . 39
4.2.10.2 Limit . 39
4.2.10.3 Conformance . 40
4.2.11 Home BS output power for adjacent channel protection . 40
4.2.11.1 Definition . 40
4.2.11.2 Limit . 40
4.2.11.3 Conformance . 41
4.2.12 Reference sensitivity level . 41
4.2.12.1 Definition . 41
4.2.12.2 Limit . 41
4.2.12.3 Conformance . 41
5 Testing for compliance with technical requirements . 42
5.1 Environmental conditions for testing . 42
5.2 Interpretation of the measurement results . 42
5.3 Essential radio test suites . 42
5.3.0 Introduction. 42
5.3.1 Spectrum emission mask . 43
5.3.1.0 General . 43
5.3.1.1 Initial conditions . 43
5.3.1.2 Procedures . 43
5.3.1.3 Test requirement . 44
5.3.2 Adjacent channel leakage power ratio (ACLR) . 44
5.3.2.1 Initial conditions . 44
5.3.2.2 Procedure . 44
5.3.2.3 Test requirement . 45
5.3.3 Transmitter spurious emis sions . 45
5.3.3.0 General . 45
5.3.3.1 Initial conditions . 45
5.3.3.2 Procedure . 45
5.3.3.3 Test requirement . 45
5.3.4 Base Station maximum output power . 46
5.3.4.0 General . 46
5.3.4.1 Initial conditions . 46
5.3.4.2 Procedure . 46
5.3.4.3 Test requirement . 46
5.3.5 Transmit intermodulation . 46
5.3.5.0 General . 46
5.3.5.1 Initial conditions . 47
5.3.5.2 Procedures . 47
5.3.5.3 Test requirement . 48
5.3.6 Receiver spurious emissions . 48
5.3.6.0 General . 48
5.3.6.1 Initial conditions . 48
5.3.6.2 Procedure . 48
5.3.6.3 Test requirement . 48
5.3.7 Blocking characteristics . 49
5.3.7.0 General . 49
5.3.7.1 Initial conditions . 49
5.3.7.2 Procedure . 50
5.3.7.3 Test requirement . 50
5.3.8 Receiver intermodulation characteristics . 50
5.3.8.0 General . 50
5.3.8.1 Initial conditions . 50
5.3.8.2 Procedures . 50
5.3.8.3 Test requirement . 51
5.3.9 Receiver adjacent channel selectivity (ACS) . 51
5.3.9.0 General . 51
ETSI

---------------------- Page: 6 ----------------------
SIST EN 301 908-3 V13.1.1:2019
 5 ETSI EN 301 908-3 V13.1.1 (2019-09)
5.3.9.1 Initial conditions . 51
5.3.9.2 Procedure . 51
5.3.9.3 Test requirement . 52
5.3.10 Home BS output power for adjacent channel protection . 52
5.3.10.1 Initial conditions . 52
5.3.10.2 Procedure . 52
5.3.10.3 Test requirement . 53
5.3.11 Reference sensitivity level . 53
5.3.11.0 General . 53
5.3.11.1 Initial Conditions . 53
5.3.11.2 Procedure . 53
5.3.11.3 Test requirement . 54
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 55
Annex B (normative): Base Stat ion configurations . 57
B.1 Receiver diversity . 57
B.2 Duplexers . 57
B.3 Power supply options . 57
B.4 Ancillary RF amplifiers . 58
B.5 BS using antenna arrays . 58
B.5.0 Introduction . 58
B.5.1 Receiver tests . 59
B.5.2 Transmitter tests . 59
B.6 Transmit diversity and MIMO transmission . 59
B.7 BS with integrated Iuant BS modem . 60
Annex C (informative): Recommended maximum measurement uncertainty . 61
Annex D (informative): Bibliography . 63
Annex E (informative): Change history . 64
History . 65


ETSI

---------------------- Page: 7 ----------------------
SIST EN 301 908-3 V13.1.1:2019
 6 ETSI EN 301 908-3 V13.1.1 (2019-09)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Mobile Standards Group
(MSG).
For non EU countries the present document may be used for regulatory (Type Approval) purposes.
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.1] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.2].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A-1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated
EFTA regulations.
The present document is part 3 of a multi-part deliverable. Full details of the entire series can be found in part 1 [i.5].

National transposition dates
Date of adoption of this EN: 23 September 2019
Date of latest announcement of this EN (doa): 31 December 2019
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 30 June 2020
Date of withdrawal of any conflicting National Standard (dow): 30 June 2021


ETSI

---------------------- Page: 8 ----------------------
SIST EN 301 908-3 V13.1.1:2019
 7 ETSI EN 301 908-3 V13.1.1 (2019-09)
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
The present document is part of a set of standards developed by ETSI that are designed to fit in a modular structure to
cover radio equipment within the scope of the Radio Equipment Directive [i.2]. The
...

Draft ETSI EN 301 908-3 V13.0.1 (2017-12)






HARMONISED EUROPEAN STANDARD
IMT cellular networks;
Harmonised Standard for access to radio spectrum;
Part 3: CDMA Direct Spread (UTRA FDD) Base Stations (BS)

---------------------- Page: 1 ----------------------
2 Draft ETSI EN 301 908-3 V13.0.1 (2017-12)



Reference
REN/MSG-TFES-13-3
Keywords
3G, 3GPP, cellular, digital, E-UTRA, IMT,
IMT-2000, IMT-Advanced, LTE, mobile, radio,
regulation, UMTS, UTRA, WCDMA

ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2017.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M logo is protected for the benefit of its Members.
GSM® and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 Draft ETSI EN 301 908-3 V13.0.1 (2017-12)

Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 7
Introduction . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 9
3 Definitions, symbols and abbreviations . 9
3.1 Definitions . 9
3.2 Symbols . 12
3.3 Abbreviations . 13
4 Technical requirements specifications . 14
4.1 Environmental profile . 14
4.2 Conformance requirements . 14
4.2.1 Introduction. 14
4.2.2 Spectrum emissions mask . 17
4.2.2.1 Definition . 17
4.2.2.2 Limit . 17
4.2.2.3 Conformance . 24
4.2.3 Adjacent channel leakage power ratio (ACLR) . 25
4.2.3.1 Definition . 25
4.2.3.2 Limits . 25
4.2.3.3 Cumulative ACLR test requirement in non-contiguous spectrum or multiple-bands . 26
4.2.3.4 Conformance . 27
4.2.4 Transmitter spurious emis sions . 27
4.2.4.1 Definition . 27
4.2.4.2 Limits . 28
4.2.4.2.1 Spurious emissions . 28
4.2.4.2.2 Co-existence with other systems . 28
4.2.4.2.3 Co-existence with services in adjacent frequency bands . 30
4.2.4.2.4 Protection of the BS receiver of own or different BS . 30
4.2.4.2.5 Co-existence with Home BS operating in other bands . 31
4.2.4.3 Conformance . 31
4.2.5 Base Station maximum output power . 31
4.2.5.1 Definition . 31
4.2.5.2 Limit . 31
4.2.5.3 Conformance . 32
4.2.6 Transmitter intermodulation . 32
4.2.6.1 Definition . 32
4.2.6.2 Limit . 33
4.2.6.3 Conformance . 33
4.2.7 Receiver spurious emissions . 33
4.2.7.1 Definition . 33
4.2.7.2 Limit . 33
4.2.7.3 Conformance . 33
4.2.8 Blocking characteristics . 34
4.2.8.1 Definition . 34
4.2.8.2 Limit . 34
4.2.8.3 Conformance . 38
4.2.9 Receiver intermodulation characteristics . 38
ETSI

---------------------- Page: 3 ----------------------
4 Draft ETSI EN 301 908-3 V13.0.1 (2017-12)
4.2.9.1 Definition . 38
4.2.9.2 Limit . 38
4.2.9.3 Conformance . 40
4.2.10 Receiver adjacent channel selectivity . 40
4.2.10.1 Definition . 40
4.2.10.2 Limit . 40
4.2.10.3 Conformance . 41
4.2.11 Home BS output power for adjacent channel protection . 41
4.2.11.1 Definition . 41
4.2.11.2 Limit . 41
4.2.11.3 Conformance . 42
4.2.12 Reference sensitivity level . 42
4.2.12.1 Definition . 42
4.2.12.2 Limit . 42
4.2.12.3 Conformance . 42
5 Testing for compliance with technical requirements . 42
5.1 Environmental conditions for testing . 42
5.2 Interpretation of the measurement results . 43
5.3 Essential radio test suites . 45
5.3.0 Introduction. 45
5.3.1 Spectrum emission mask . 45
5.3.1.0 General . 45
5.3.1.1 Initial conditions . 45
5.3.1.2 Procedures . 46
5.3.1.3 Test requirement . 46
5.3.2 Adjacent channel leakage power ratio (ACLR) . 46
5.3.2.1 Initial conditions . 46
5.3.2.2 Procedure . 47
5.3.2.3 Test requirement . 47
5.3.3 Transmitter spurious emis sions . 47
5.3.3.0 General . 47
5.3.3.1 Initial conditions . 47
5.3.3.2 Procedure . 48
5.3.3.3 Test requirement . 48
5.3.4 Base Station maximum output power . 48
5.3.4.0 General . 48
5.3.4.1 Initial conditions . 48
5.3.4.2 Procedure . 49
5.3.4.3 Test requirement . 49
5.3.5 Transmit intermodulation . 49
5.3.5.0 General . 49
5.3.5.1 Initial conditions . 49
5.3.5.2 Procedures . 49
5.3.5.3 Test requirement . 50
5.3.6 Receiver spurious emissions . 50
5.3.6.0 General . 50
5.3.6.1 Initial conditions . 50
5.3.6.2 Procedure . 51
5.3.6.3 Test requirement . 51
5.3.7 Blocking characteristics . 51
5.3.7.0 General . 51
5.3.7.1 Initial conditions . 51
5.3.7.2 Procedure . 52
5.3.7.3 Test requirement . 53
5.3.8 Receiver intermodulation characteristics . 53
5.3.8.0 General . 53
5.3.8.1 Initial conditions . 53
5.3.8.2 Procedures . 53
5.3.8.3 Test requirement . 54
5.3.9 Receiver adjacent channel selectivity (ACS) . 54
5.3.9.0 General . 54
ETSI

---------------------- Page: 4 ----------------------
5 Draft ETSI EN 301 908-3 V13.0.1 (2017-12)
5.3.9.1 Initial conditions . 54
5.3.9.2 Procedure . 54
5.3.9.3 Test requirement . 54
5.3.10 Home BS output power for adjacent channel protection . 55
5.3.10.1 Initial conditions . 55
5.3.10.2 Procedure . 55
5.3.10.3 Test requirement . 55
5.3.11 Reference sensitivity level . 55
5.3.11.0 General . 55
5.3.11.1 Initial Conditions . 56
5.3.11.2 Procedure . 56
5.3.11.3 Test requirement . 56
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 57
Annex B (normative): Base Stat ion configurations . 59
B.1 Receiver diversity . 59
B.2 Duplexers . 59
B.3 Power supply options . 59
B.4 Ancillary RF amplifiers . 60
B.5 BS using antenna arrays . 60
B.5.0 Introduction . 60
B.5.1 Receiver tests . 61
B.5.2 Transmitter tests . 61
B.6 Transmit diversity and MIMO transmission . 61
B.7 BS with integrated Iuant BS modem . 62
Annex C (informative): Environmental profile specification . 63
Annex D (informative): Bibliography . 64
Annex E (informative): Change history . 65
History . 66


ETSI

---------------------- Page: 5 ----------------------
6 Draft ETSI EN 301 908-3 V13.0.1 (2017-12)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee Mobile Standards
Group (MSG), and is now submitted for the combined Public Enquiry and Vote phase of the ETSI standards EN
Approval Procedure.
For non EU countries the present document may be used for regulatory (Type Approval) purposes.
The present document has been prepared under Commission's standardisation request C(2015) 5376 [i.1] final one
voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation of the laws
of the Member States relating to the making available on the market of radio equipment and repealing Directive
1999/5/EC [i.2].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A-1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated
EFTA regulations.
The present document is part 3 of a multi-part deliverable. Full details of the entire series can be found in part 1 [i.5].

Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa


ETSI

---------------------- Page: 6 ----------------------
7 Draft ETSI EN 301 908-3 V13.0.1 (2017-12)
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
The present document is part of a set of standards developed by ETSI that are designed to fit in a modular structure to
cover radio equipment within the scope of the Radio Equipment Directive [i.2]. The present document is produced
following the guidance in ETSI EG 203 336 [i.3] as applicable.

ETSI

---------------------- Page: 7 ----------------------
8 Draft ETSI EN 301 908-3 V13.0.1 (2017-12)
1 Scope
The present document applies to the following equipment types:
1) Stations for IMT 2000 CDMA Direct Spread (UTRA FDD).
This radio equipment type is capable of operating in all or any part of the frequency bands given in table 1-1.
Table 1-1: UTRA FDD Base Station operating bands
UTRA FDD Direction of transmission UTRA FDD Base Station operating bands
band
I Transmit 2 110 MHz to 2 170 MHz
Receive 1 920 MHz to 1 980 MHz
III Transmit 1 805 MHz to 1 880 MHz
Receive 1 710 MHz to 1 785 MHz
VII Transmit 2 620 MHz to 2 690 MHz
Receive 2 500 MHz to 2 570 MHz
VIII Transmit 925 MHz to 960 MHz
Receive 880 MHz to 915 MHz
XX Transmit 791 MHz to 821 MHz
Receive 832 MHz to 862 MHz
XXII Transmit 3 510 MHz to 3 590 MHz
Receive 3 410 MHz
...