SIST EN 2424:2008
(Main)Aerospace series - Marking of aerospace products
Aerospace series - Marking of aerospace products
This standard specifies the rules for the marking of aerospace products.
It is applicable whenever referenced in the definition document of the product.
Luft und Raumfahrt - Kennzeichnung von Luft- und Raumfahrtteilen
Série aérospatiale - Marquage des produits aérospatiaux
Aeronavtika - Označevanje proizvodov v aeronavtiki
General Information
Relations
Overview
SIST EN 2424:2008 is a European standard developed by CEN, specifying the rules for marking aerospace products. It applies to all aerospace products when referenced in their definition documents. The standard ensures consistent identification of aerospace parts, supporting traceability, quality control, and regulatory compliance throughout the aerospace industry.
This marking protocol is essential for identifying both the product and its manufacturer, relying on clear, permanent markings that meet predefined style and legibility requirements. SIST EN 2424:2008 supersedes the earlier 1995 version and aims to harmonize marking practices across CEN member countries, including Austria, Germany, France, UK, and many others.
Key Topics
Scope and Application
SIST EN 2424:2008 defines marking requirements used whenever referenced by a product’s definition document, primarily focusing on aerospace components.Manufacturer Identification
Marking includes the manufacturer’s monogram or name, registered with ASD-STAN, ensuring clear traceability.Marking Styles
The standard describes several marking styles (A to P), ranked by preference:- Style A: Full identification including product identity block and manufacturer monogram (preferred).
- Styles B, C, D, etc.: Alternative markings used when space or product characteristics limit Style A.
- Special provisions exist for threaded products and packaging labels.
Marking Practices
- Positioning must avoid impairment to product function and allow identification in assembled conditions.
- Markings must be permanent, made by indention or embossing within specified depth limits (0.05 mm to 0.25 mm).
- Legibility is mandatory without magnification, with preferred character height 1.5 mm; smaller sizes allowed only under restricted conditions.
Product Identification Priority
Where space allows, the EN part number takes precedence over manufacturer part numbers.
Applications
Aerospace Manufacturing
Facilitates the accurate identification and traceability of aerospace components for manufacturers and suppliers.Quality Assurance and Compliance
Enables regulatory bodies and quality inspectors to verify the origin and conformity of aerospace parts during production and maintenance.Supply Chain Management
Standardized markings help streamline logistics, inventory management, and inspection processes across the aerospace supply chain.Maintenance and Repairs
Markings ensure replacement parts are correctly identified, improving safety and reliability in aerospace operations.
Related Standards
TR 3198 - Aerospace series for Manufacturer's Identification Monograms
Provides additional guidance on the registration and use of manufacturer monograms referenced in SIST EN 2424:2008.EN 2424:1995
The previous iteration replaced by the 2008 update to reflect improved marking practices.Other aerospace standards covering product specifications, quality management, and traceability, often referencing SIST EN 2424:2008 for marking requirements.
Keywords: SIST EN 2424:2008, aerospace product marking, aerospace standards, manufacturer identification, part traceability, aerospace component marking, aerospace quality assurance, aerospace supply chain, permanent marking, aerospace industry standards.
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Luft und Raumfahrt - Kennzeichnung von Luft- und RaumfahrtteilenSérie aérospatiale - Marquage des produits aérospatiauxAerospace series - Marking of aerospace products49.035Sestavni deli za letalsko in vesoljsko gradnjoComponents for aerospace constructionICS:Ta slovenski standard je istoveten z:EN 2424:2008SIST EN 2424:2008en01-september-2008SIST EN 2424:2008SLOVENSKI
STANDARDSIST EN 2424:20011DGRPHãþD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 2424May 2008ICS 49.035Supersedes EN 2424:1995
English VersionAerospace series - Marking of aerospace productsSérie aérospatiale - Marquage des produits aérospatiauxLuft und Raumfahrt - Kennzeichnung von Luft- undRaumfahrtteilenThis European Standard was approved by CEN on 7 March 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2008 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 2424:2008: ESIST EN 2424:2008
...
Frequently Asked Questions
SIST EN 2424:2008 is a standard published by the Slovenian Institute for Standardization (SIST). Its full title is "Aerospace series - Marking of aerospace products". This standard covers: This standard specifies the rules for the marking of aerospace products. It is applicable whenever referenced in the definition document of the product.
This standard specifies the rules for the marking of aerospace products. It is applicable whenever referenced in the definition document of the product.
SIST EN 2424:2008 is classified under the following ICS (International Classification for Standards) categories: 49.035 - Components for aerospace construction. The ICS classification helps identify the subject area and facilitates finding related standards.
SIST EN 2424:2008 has the following relationships with other standards: It is inter standard links to SIST EN 2424:2001. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
You can purchase SIST EN 2424:2008 directly from iTeh Standards. The document is available in PDF format and is delivered instantly after payment. Add the standard to your cart and complete the secure checkout process. iTeh Standards is an authorized distributor of SIST standards.
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...