SIST EN ISO 23537-2:2017

SLOVENSKI STANDARD
01-januar-2017
=DKWHYH]DVSDOQHYUHþHGHO/DVWQRVWLWNDQLQHLQPDWHULDOD,62
Requirements for sleeping bags - Part 2: Fabric and material properties (ISO 23537-
2:2016)
Anforderungen an Schlafsäcke - Teil 2: Gewebe- und Materialeigenschaften (ISO 23537-
2:2016)
Exigences pour les sacs de couchage - Partie 2: Caractéristiques tissues et matérielles
(ISO 23537-2:2016)
Ta slovenski standard je istoveten z: EN ISO 23537-2:2016
ICS:
97.200.30 Oprema za taborjenje in Camping equipment and
tabori camp-sites
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 23537-2
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2016
EUROPÄISCHE NORM
ICS 97.200.30 Supersedes EN 13537:2012
English Version
Requirements for sleeping bags - Part 2: Fabric and
material properties (ISO 23537-2:2016)
Exigences pour les sacs de couchage - Partie 2: Anforderungen an Schlafsäcke - Teil 2: Gewebe- und
Propriétés de l'étoffe et des matières (ISO 23537- Materialeigenschaften (ISO 23537-2:2016)
2:2016)
This European Standard was approved by CEN on 5 September 2016.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 23537-2:2016 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
European foreword
This document (EN ISO 23537-2:2016) has been prepared by Technical Committee ISO/TC 83 "Sports
and other recreational facilities and equipment" in collaboration with Technical Committee
CEN/TC 136 “Sports, playground and other recreational facilities and equipment” the secretariat of
which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2017, and conflicting national standards shall be
withdrawn at the latest by April 2017.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document supersedes EN 13537:2012.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 23537-2:2016 has been approved by CEN as EN ISO 23537-2:2016 without any
modification.
INTERNATIONAL ISO
STANDARD 23537-2
First edition
2016-10-01
Requirements for sleeping bags —
Part 2:
Fabric and material properties
Exigences pour les sacs de couchage —
Partie 2: Propriétés de l’étoffe et des matières
Reference number
ISO 23537-2:2016(E)
©
ISO 2016
ISO 23537-2:2016(E)
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved

ISO 23537-2:2016(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Requirements and test methods . 2
3.1 Fabrics . 2
3.1.1 Down proofness . 2
3.1.2 Synthetic fibre proofness . 2
3.1.3 Mechanical properties . 2
3.2 Filling material . 3
3.2.1 Feather and/or down . . 3
3.2.2 Filling material other than feather and/or down – Mass per unit area . 3
3.3 Finished articles . 3
3.3.1 Inside dimensions . 3
3.3.2 Total mass . 4
3.3.3 Volume under load . 4
4 Test report . 4
5 Marking . 4
6 Information supplied to the consumer . 4
6.1 Mandatory information . 4
6.2 Optional information . 6
ISO 23537-2:2016(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment,
as well as information about ISO’s adherence to the World Trade Organization (WTO) principles in the
Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/
...