SIST EN 14151:2010
(Main)Geosynthetics - Determination of burst strength
Geosynthetics - Determination of burst strength
This European Standard specifies a method for the determination of bi-axial properties (burst strength) of geosynthetics.
This method applies to geotextiles, geosynthetic barriers and their related products. It applies to clay geosynthetic barriers only when tested in dry conditions.
Geokunststoffe - Bestimmung der Berstdruckfestigkeit
Diese Europäische Norm legt ein Verfahren zur Bestimmung der biaxialen Eigenschaften (Berstdruck-festigkeit) von Geokunststoffen fest.
Das vorliegende Verfahren gilt für Geotextilien, geosynthetische Dichtungsbahnen und deren zugehörige Erzeugnisse. Die Norm gilt nur für geosynthetische Tondichtungsbahnen, wenn diese im trockenen Zustand geprüft werden.
Géosynthétiques - Détermination de la résistance à l'éclatement
La présente Norme européenne prescrit une méthode de détermination des propriétés biaxiales (résistance à l’éclatement) des géosynthétiques.
Cette méthode s’applique aux géotextiles, géomembranes et produits apparentés. Elle ne s’applique aux géosynthétiques bentonitiques que préalablement à l'hydratation de ces matériaux.
Geosintetika - Ugotavljanje razpočne trdnosti
Ta evropski standard opredeljuje metodo za ugotavljanje dvoosnih lastnosti (razpočne trdnosti) geosintetike. Ta metoda velja za geotekstilije, geosintetične ovire in sorodne proizvode. Za glinene geosintetične ovire velja le, kadar se preskušajo v suhih razmerah.
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Geokunststoffe - Bestimmung der BerstdruckfestigkeitGéosynthétiques - Détermination de la résistance à l'éclatementGeosynthetics - Determination of burst strength59.080.70GeotekstilijeGeotextilesICS:Ta slovenski standard je istoveten z:EN 14151:2010SIST EN 14151:2010en,de01-september-2010SIST EN 14151:2010SLOVENSKI
STANDARD
SIST EN 14151:2010
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 14151
June 2010 ICS 59.080.70; 91.100.50 English Version
Geosynthetics - Determination of burst strength
Géosynthétiques - Détermination de la résistance à l'éclatement
Geokunststoffe - Bestimmung der Berstdruckfestigkeit This European Standard was approved by CEN on 12 May 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 14151:2010: ESIST EN 14151:2010
EN 14151:2010 (E) 2 Contents Page Foreword .31 Scope .42 Normative references .43 Terms and definitions .44 Principle .45 Apparatus .45.1 General .45.2 Cell .55.3 Deflection measurement .55.4 Pressure measurement .65.5 Volume control .66 Specimens .67 Conditioning .68 Procedure .68.1 General .68.2 Volume control .78.3 Diaphragm correction .79 Calculations .710 Test report .9Bibliography . 10 SIST EN 14151:2010
EN 14151:2010 (E) 3 Foreword This document (EN 14151:2010) has been prepared by Technical Committee CEN/TC 189 “Geosynthetics”, the secretariat of which is held by NBN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2010, and conflicting national standards shall be withdrawn at the latest by December 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. SIST EN 14151:2010
EN 14151:2010 (E) 4 1 Scope This European Standard specifies a method for the determination of bi-axial properties (burst strength) of geosynthetics. This method applies to geotextiles, geosynthetic barriers and their related products. It applies to clay geosynthetic barriers only when tested in dry conditions. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN ISO 10318:2005, Geosynthetics — Terms and definitions (ISO 10318:2005) ISO 554, Standard atmospheres for conditioning and/or testing — Specifications 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN ISO 10318:2005 apply. 4 Principle A circular specimen, clamped around its edge, is subjected to a gradually increasing normal hydraul
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.