SIST EN 301 002-3 V1.1.4:2005
(Main)Integrated Services Digital Network (ISDN); Security tools (SET) procedures; Digital Subscriber Signalling System No. one (DSS1) protocol; Part 3: Test Suite Structure and Test Purposes (TSS&TP) specification for the user
- Abstract
Test specification for RE/SPS-05141-1.
- Status
- Published
- Publication Date
- 30-Jun-2005
- Technical Committee
- SPN - Services and Protocols for Networks
- Current Stage
- 6060 - National Implementation/Publication (Adopted Project)
- Start Date
- 01-Jul-2005
- Due Date
- 01-Jul-2005
- Completion Date
- 01-Jul-2005
SIST EN 301 002-3 V1.1.4:2005 is the Slovenian adoption of ETSI EN 301 002-3 Version 1.1.4. It specifies the Test Suite Structure and Test Purposes (TSS&TP) for the user side of Integrated Services Digital Network (ISDN) Security tools (SET) procedures over the Digital Subscriber Signalling System No. one (DSS1) protocol. It is meant for conformance testing of user-side implementations at the T reference point or the coincident S and T reference point.
What does SIST EN 301 002-3 V1.1.4:2005 specify?
SIST EN 301 002-3 V1.1.4:2005 defines the user-side conformance test structure for SET procedures in ISDN. Its scope is limited to Test Suite Structure and Test Purposes, so it tells you what should be tested and how the tests are grouped, not the full protocol itself.
The document is organized into these main clauses:
- Scope
- References
- Definitions and abbreviations
- Test Suite Structure (TSS)
- Test Purposes (TP)
- Compliance
- Requirements for a comprehensive testing service
The scope links this part to EN 301 002-1 as the base protocol specification and points to other parts of the same series for ATS and PIXIT material, including the network-side parts.
What are the key requirements of SIST EN 301 002-3 V1.1.4:2005?
SIST EN 301 002-3 V1.1.4:2005 builds its test purposes from externally observable behaviour of the Implementation Under Test (IUT). In practice, that means the test cases focus on messages, states and responses that a lab can see on the interface.
Test Suite Structure and naming
Clause 4 groups the user test purposes into one test suite structure for signalling procedures at the coincident S and T reference point and for interworking with private ISDN. The groups are:
- Registration - PIN
- Notification of possible fraudulent use
- PIN
- TAN
Clause 5.1 defines the TP identifier format as <ss>_<iut><group>_<nnn>. This matters because ATS, test reports and PICS-based selection all rely on the same naming convention.
How the test purposes are built
Clause 5.1 says the TPs are based on EN 301 002-1 and on the PICS specification EN 301 002-2. The document also states that TPs are mandatory unless a selection criterion applies, and selection criteria must map to a PICS item. In practice, this lets a tester remove only the cases that the implementation has not claimed.
For the user TPs, the document assumes valid messages and information elements unless otherwise stated. It also specifies how FACILITY messages are transported, using the point-to-point connectionless bearer-independent mechanism with dummy call reference, or the broadcast mechanism where that applies. That is important because it fixes the test setup and the expected signalling path.
Main user procedures covered
The Registration - PIN tests in clause 5.2.1.1 cover ModifyPin behaviour. They check the normal invoke, the return result, several return error cases, and timer expiry in the Registrate Request state. In practice, this shows whether the implementation accepts valid PIN registration, rejects invalid data correctly, and reacts properly when the registration timer expires.
The Notification of possible fraudulent use tests in clause 5.2.1.3 check both PIN and TAN handling. The expected reaction is no outgoing message and remaining in Idle when a possible fraudulent use indication is received, with the Called Party Number condition depending on whether the multiple subscriber number service is present. This is the core user-side behaviour the standard wants to verify.
Compliance and testing service
Clause 6 says a compliant ATS must use the same naming conventions, preserve the relationship between test groups, TPs and PICS entries, and comply with ISO/IEC 9646-2. Clause 7 adds that a comprehensive testing service for network equipment shall use the Remote test method as a minimum. For users of the document, that defines how an executable test suite is assembled and how it is expected to be run.
What terms does SIST EN 301 002-3 V1.1.4:2005 define?
- Abstract Test Suite (ATS) - the set of executable test cases derived from the test purposes.
- Implementation Under Test (IUT) - the implementation being tested for conformance.
- Protocol Implementation Conformance Statement (PICS) - the declaration used to select which test purposes apply.
- Protocol Implementation eXtra Information for Testing (PIXIT) - extra information needed to run the tests.
- Test Purpose (TP) - a single stated objective for one test case.
- Test Suite Structure (TSS) - the grouping of test purposes into suites and groups.
- Personal Identification Number (PIN) - the security number used in the SET procedures for registration.
- Transaction Number (TAN) - the transaction-related security value used in the SET procedures.
Who uses SIST EN 301 002-3 V1.1.4:2005?
SIST EN 301 002-3 V1.1.4:2005 is used by conformance test labs, protocol developers, and equipment vendors that implement SET over DSS1. Quality and compliance teams use it to plan ATS development, select test cases from a PICS, and check user-side behaviour at the T reference point or coincident S and T reference point.
It is also relevant to organizations that need to verify registration of PIN security, handling of fraudulent-use notifications, and the correct mapping between protocol behaviour and declared features.
What changed in SIST EN 301 002-3 V1.1.4:2005 from the previous edition?
SIST EN 301 002-3 V1.1.4:2005 is Version 1.1.4 of EN 301 002-3, and the history records an earlier Version 1.1.3. The document history also records the publication trail for Version 1.1.4.
Which standards are used with SIST EN 301 002-3 V1.1.4:2005?
- ETSI EN 301 002-1 - the base protocol specification that the test purposes are derived from.
- ETSI EN 301 002-2 - the PICS proforma used to determine which tests apply.
- ISO/IEC 9646-1 - defines conformance testing concepts such as ATS, IUT, PICS and PIXIT.
- ISO/IEC 9646-2 - gives the Abstract Test Suite specification rules used for compliance.
- ETSI EN 300 196-1 - provides supplementary service protocol details used for components and transport mechanisms.
- ITU-T Recommendation I.411 - defines ISDN user-network reference configurations.
- ETSI EN 300 403-1 - provides DSS1 basic call control and the dummy call reference context.
- ITU-T Recommendation I.112 - provides ISDN vocabulary and reference definitions.
- ITU-T Recommendation E.164 - defines the numbering plan used for ISDN numbers.
- ITU-T Recommendation I.210 - provides principles for telecommunication services supported by ISDN.
- ETSI ETS 300 406 - gives testing methodology used when generating realistic, observable test purposes.
- ETSI ETR 232 - provides security terminology, including PIN.
- ETSI EN 301 132 - defines SET for telecommunication services, including security tool and TAN.
What does the SIST EN 301 002-3 V1.1.4:2005 document contain?
The document contains a figure for the test suite structure, a TP identifier scheme, and a table showing the structure of a single TP. It also contains the detailed user test purposes for PIN registration and for notifications of possible fraudulent use of PIN and TAN.
Clause 5.1 explains how TPs are named and structured, so a test team can trace a test case back to the base conformance requirement and the PICS selection. Clause 5.2.1 gives the actual message and state-based test purposes, while clauses 6 and 7 define how an ATS should be built and what a comprehensive testing service should use.
Get Certified
Connect with accredited certification bodies for this standard
ANCE
Mexican certification and testing association.
Intertek Slovenia
Intertek testing, inspection, and certification services in Slovenia.
LNE (Laboratoire National de Métrologie et d'Essais)
French national laboratory for metrology and testing.
Sponsored listings
Frequently Asked Questions
SIST EN 301 002-3 V1.1.4:2005 is a standard published by the Slovenian Institute for Standardization (SIST). Its full title is "Integrated Services Digital Network (ISDN); Security tools (SET) procedures; Digital Subscriber Signalling System No. one (DSS1) protocol; Part 3: Test Suite Structure and Test Purposes (TSS&TP) specification for the user". This standard covers: Test specification for RE/SPS-05141-1.
Test specification for RE/SPS-05141-1.
SIST EN 301 002-3 V1.1.4:2005 is classified under the following ICS (International Classification for Standards) categories: 33.080 - Integrated Services Digital Network (ISDN). The ICS classification helps identify the subject area and facilitates finding related standards.
SIST EN 301 002-3 V1.1.4:2005 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
SLOVENSKI STANDARD
01-julij-2005
'LJLWDOQRRPUHåMH]LQWHJULUDQLPLVWRULWYDPL ,6'1 3RVWRSNLYDURYDOQHJDRURGMD
6(7 3URWRNROGLJLWDOQHQDURþQLãNHVLJQDOL]DFLMHãW '66 GHO =JUDGED
SUHVNXãDOQHJDQL]DLQQDPHQLSUHVNXãDQMD 766 73 6SHFLILNDFLMD]DXSRUDEQLND
Integrated Services Digital Network (ISDN); Security tools (SET) procedures; Digital
Subscriber Signalling System No. one (DSS1) protocol; Part 3: Test Suite Structure and
Test Purposes (TSS&TP) specification for the user
Ta slovenski standard je istoveten z: EN 301 002-3 Version 1.1.4
ICS:
33.080 Digitalno omrežje z Integrated Services Digital
integriranimi storitvami Network (ISDN)
(ISDN)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
European Standard (Telecommunications series)
Integrated Services Digital Network (ISDN);
Security tools (SET) procedures;
Digital Subscriber Signalling System No. one (DSS1) protocol;
Part 3: Test Suite Structure and Test Purposes (TSS&TP)
specification for the user
2 ETSI EN 301 002-3 V1.1.4 (2000-05)
Reference
DEN/SPS-05141-3
Keywords
DSS1, ISDN, security, supplementary service,
TSS&TP, user
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.:+33492944200 Fax:+33493654716
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network
drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at http://www.etsi.org/tb/status/
If you find errors in the present document, send your comment to:
editor@etsi.fr
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2000.
All rights reserved.
ETSI
3 ETSI EN 301 002-3 V1.1.4 (2000-05)
Contents
Intellectual Property Rights.4
Foreword .4
1 Scope.5
2 References.5
3 Definitions and abbreviations .6
3.1 Definitions.6
3.1.1 Definitions related to conformance testing .6
3.1.2 Definitions related to EN 301 002-1.6
3.2 Abbreviations .7
4 Test Suite Structure (TSS) .7
5 Test Purposes (TP).7
5.1 Introduction .7
5.1.1 TP naming convention .7
5.1.2 Source of TP definition.8
5.1.3 TP structure.8
5.1.4 Test strategy.9
5.2 User TPs for SET .9
5.2.1 Signalling procedures at the coincident S and T reference point and for interworking with private
ISDN.9
5.2.1.1 Registration - PIN .9
5.2.1.2 Invocation and Operation.10
5.2.1.3 Notification of possible fraudulent use.10
5.2.1.3.1 PIN .10
5.2.1.3.2 TAN.11
6 Compliance .11
7 Requirements for a comprehensive testing service.11
Bibliography.12
History.13
ETSI
4 ETSI EN 301 002-3 V1.1.4 (2000-05)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect
of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server
(http://www.etsi.org/ipr).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in SR 000 314 (or the updates on the ETSI Web server)
which are, or may be, or may become, essential to the present document.
Foreword
This European Standard (Telecommunications series) has been produced by ETSI Technical Committee Services and
Protocols for Advanced Networks (SPAN).
The present document is part 3 of a multi-part EN covering the Integrated Services Digital Network (ISDN); Security
tools (SET) procedures; Digital Subscriber Signalling System No. one (DSS1) protocol, as identified below:
Part 1: "Protocol specification";
Part 2: "Protocol Implementation Conformance Statement (PICS) proforma specification";
Part 3: "Test Suite Structure and Test Purposes (TSS&TP) specification for the user";
Part 4: "Abstract Test Suite (ATS) and partial Protocol Implementation eXtra Information for Testing (PIXIT)
proforma specification for the user";
Part 5: "Test Suite Structure and Test Purposes (TSS&TP) specification for the network";
Part 6: "Abstract Test Suite (ATS) and partial Protocol Implementation eXtra Information for Testing (PIXIT)
proforma specification for the network".
National transposition dates
Date of adoption of this EN: 28 April 2000
Date of latest announcement of this EN (doa): 31 July 2000
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 January 2001
Date of withdrawal of any conflicting National Standard (dow): 31 January 2001
ETSI
5 ETSI EN 301 002-3 V1.1.4 (2000-05)
1 Scope
The present document specifies the Test Suite Structure and Test Purposes (TSS&TP) for the User side of the T
reference point or coincident S and T reference point (as defined in ITU-T Recommendation I.411 [6]) of
implementations conforming to the stage three standard for the Security tools (SET) procedures for the pan-European
Integrated Services Digital Network (ISDN) by means of the Digital Subscriber Signalling System No. one (DSS1)
protocol, EN 301 002-1 [1].
A further part of the present document specifies the Abstract Test Suite (ATS) and partial PIXIT proforma based on the
present document. Other parts specify the TSS&TP and the ATS and partial PIXIT proforma for the Network side of the
T reference point or coincident S and T reference point of implementations conforming to EN 301 002-1 [1].
2 References
The following documents contain provisions which, through reference in this text, constitute provisions of the present
document.
• References are either specific (identified by date of publication, edition number, version number, etc.) or
non-specific.
• For a specific reference, subsequent revisions do not apply.
• For a non-specific reference, the latest version applies.
• A non-specific reference to an ETS shall also be taken to refer to later versions published as an EN with the same
number.
[1] ETSI EN 301 002-1: "Integrated Services Digital Network (ISDN); Security tools (SET)
procedures; Digital Subscriber Signalling System No. one (DSS1) protocol; Part 1: Protocol
specification".
[2] ETSI EN 301 002-2: "Integrated Services Digital Network (ISDN); Security tools (SET)
procedures; Digital Subscriber Signalling System No. one (DSS1) protocol; Part 2: Protocol
Implementation Conformance Statement (PICS) proforma specification".
[3] ISO/IEC 9646-1: "Information technology - Open Systems Interconnection - Conformance testing
methodology and framework - Part 1: General concepts".
[4] ISO/IEC 9646-2: "Information technology - Open Systems Interconnection - Conformance testing
methodology and framework - Part 2: Abstract Test Suite specification".
[5] ETSI EN 300 196-1: "Integrated Services Digital Network (ISDN); Generic functional protocol for
the support of supplementary services; Digital Subscriber Signalling System No. one (DSS1)
protocol; Part 1: Protocol specification".
[6] ITU-T Recommendation I.411 (1993): "ISDN user-network interfaces – Reference
configurations".
[7] ETSI EN 300 403-1: "Integrated Services Digital Network (ISDN); Digital Subscriber Signalling
System No. one (DSS1) protocol; Signalling network layer for circuit-mode basic call control;
Part 1: Protocol specification [ITU-T Recommendation Q.931 (1993), modified]".
[8] ITU-T Recommendation I.112 (1993): "Vocabulary of terms for ISDNs".
[9] ITU-T Recommendation E.164 (1997): "The international public telecommunication numbering
plan".
[10] ITU-T Recommendation I.210 (1993): "Principles of telecommunication services supported by an
ISDN and the means to describe them".
ETSI
6 ETSI EN 301 002-3 V1.1.4 (2000-05)
[11] ETSI ETS 300 406 (1995): "Methods for Testing and Specification (MTS); Protocol and profile
conformance testing specifications; Standardization methodology".
[12] ETSI ETR 232: "Security Techniques Advisory Group (STAG); Glossary of security terminology".
[13] ETSI EN 301 132: "Integrated Services Digital Network (ISDN); Security tools (SET) for use
within telecommunication services".
3 Definitions and abbreviations
3.1 Definitions
For the purposes of the present document, the following terms and definitions apply.
3.1.1 Definitions related to conformance testing
Abstract Test Suite (ATS): refer to ISO/IEC 9646-1 [3].
Implementation Under Test (IUT): refer to ISO/IEC 9646-1 [3].
Protocol Implementation Conformance Statement (PICS): refer to ISO/IEC 9646-1 [3].
PICS proforma: refer to ISO/IEC 9646-1 [3].
Protocol Implementation eXtra Information for Testing (PIXIT): refer to ISO/IEC 9646-1 [3].
PIXIT proforma: refer to ISO/IEC 9646-1 [3].
system under test: refer to ISO/IEC 9646-1 [3].
Test Purpose (TP): refer to ISO/IEC 9646-1 [3].
3.1.2 Definitions related to EN 301 002-1
component: see EN 300 196-1 [5], subclause 11.2.2.1.
Dummy call reference: see EN 300 403-1 [7], subclause 4.3.
Integrated Services Digital Network (ISDN): see ITU-T Recommendation I.112 [8], definition 308.
invoke component: see EN 300
...